A-B Dyno Testing ZZP Stage II Ecotec Cams // Cobalt Build Episode 18

Рет қаралды 2,234

2 ай бұрын

Tyler is BACK on the street in his "Ole Blue" LSJ and he's ready for more upgrades! This time, he's got his sights set on the cams and valve springs.
With the new parts going in, we figured it was the perfect opportunity to do some A-B testing on our Stage II Ecotec cams and 82lb valve springs. Tyler strapped Ole Blue to the dyno for some stock cam numbers before installing his new bump sticks and the results are in! Picked up 20 wheel and now it's looking like time to go down in pulley size.
These cams will raise your LSJ powerband 700-1000rpm and make peak power at around 7500-7800rpm! GOFASTNOTBROKE
216/218 @ 1mm and 10.78mm/10.69mm lift, 111 LSA
Cams:
zzperformance.com/collections...
Valve Springs:
zzperformance.com/collections...
#ecotec #cobalt #dynotested #camshaft #supercharged #lsj
ZZP is located in Wyoming, MI. We are the world’s largest supplier of aftermarket performance parts for 3800, Sonic/Cruze, Ecotec, and ATS platforms, providing industry-leading customer service and support.
Our staff of professionals has experienced knowledge in all the vehicle platforms we represent. ZZPerformance is dedicated to 100% customer satisfaction. We provide you with highly specific technical information, that can’t be found anywhere else.
Interested in modding your car? Check out our parts at zzperformance.com
Questions about modding? Email us at customerservice@zzperformance.com

Пікірлер: 28

@christianshafer1886 2 ай бұрын

I cant wait to see the different pulley size comparison video! It will be very interesting to see how much power is gained by dropping each pulley size.

@Siviqs 2 ай бұрын

the blue devil returns!

@pooper409 2 ай бұрын

Thank you Tyler for holding down the LSJ blower setup. RIP old blue “You’re my boy blue!”

@mdhaynes86 2 ай бұрын

I would like to see some back to back tests on a ported blower and LS4 throttle body.

@codygermscheid7081 2 ай бұрын

Definitely try out some different pulley sizes but I would be curious on a test between a factory blower and a ported blower and an LS4 throttle body

@flit6849 2 ай бұрын

He’d gain either way Not sure ifZZP is porting M62 blowers though? There was a great outlet / inlet port design floating around the forum that gained quite a bit of power.

@mccartyb03 2 ай бұрын

@@flit6849 Category V did mine. I just ditched the LS4 TB though, the drivability sucked for what was probably a small gain.

@flit6849 2 ай бұрын

@@mccartyb03 There’s a learning curve for sure with the LS4. Some love it, some dont. The gain is larger the higher the engine revs.

@choppstikkx 2 ай бұрын

YEEEEEEEEEES

@deebalt071 2 ай бұрын

Little side question. Is it normal to do the pull in 3rd gear opposed to 4th gear in these cars?

@flit6849 2 ай бұрын

❤

@chrispisano5791 2 ай бұрын

The spring compressor is what I wanna know about. If I decide to get the 82# springs.

@ZZPerformanceChannel 2 ай бұрын

We'll have an install video out next week!

@rosslawrence4628 2 ай бұрын

E85, intake, exhaust, A test 254hp, 211tq. You forgot to mention what injectors you are running, as the stock green 32lb/hour ones won't support E85. I'm at 98% injector duty cycle on E10, with the stock LSJ. Are you running Siemens Deka or Bosch EV14 injectors?

@gbrunner24 2 ай бұрын

If you run through our previous videos in the series I cover all the bases as to what's on the car. But for ease for ya: Siemens 60# injectors, ZZP cold air intake, ZZP mid length header and 2.5" exhaust back to the stock muffler, pump E85, dual pass end plate, option B, ZZP stealth heat exchanger, ZZP S1 intercooler pump, and my tuning.

@rosslawrence4628 2 ай бұрын

@@gbrunner24 Now you have me binge watching your cobalt build. Not sure how I missed all this, but nice content!

@jadenharris932 24 күн бұрын

Did you have the ati balancer and neutral balance shafts?

@gbrunner24 21 күн бұрын

Nope. Stock crank damper and stock balance shafts are in place.

@thomasmixon5555 2 ай бұрын

What wheels and tires do you have would love to know

@gbrunner24 2 ай бұрын

They are Enkei TS-10 18x8 with 215/45/18 Toyo Proxes A40. The car has a 5x114.3 hub swap on it.

@kirbyswarp 2 ай бұрын

How many degrees of timing are you running?

@gbrunner24 2 ай бұрын

I like to keep it right around 21°. A test had a little more timing, ended up at 22.5° around 7k. B test was dead on my 21° mark out the top end.

@kirbyswarp 2 ай бұрын

@@gbrunner24 Did you try running any more, or did it stop making power?

@gbrunner24 2 ай бұрын

@@kirbyswarp I did not, stopped there. Picked up about 6whp going from 20 to 21. May have made a little more going a little higher, but that 21 mark is what I like to shoot for.

@Pudding175 2 ай бұрын

Tyler, are you running the ATI crank pully or stock? Im curious what sized belt you are running. I have the ATI with the factory supercharger pully on my 05 redline and can't find a belt that well fit.

@gbrunner24 2 ай бұрын

Factory crank pulley and OEM length belt at this point. Overdrive ATI or under?