A Complete Guide to Perform a 60K-120K Timing Belt Service on a 1990-1996 Nissan 300zx! (EP. 5)

Рет қаралды 41,105

4 жыл бұрын

This video is a complete guide on how to perform a 60k-120k service on a 1990-1996 Nissan 300zx. This guide show how to remove the timing belt, pulleys, gears, and everything inbetween with the correct torque specs given from the FSM for a Z32. If you follow these steps this install should go smoothly and be beneficial for anyone who performs this procedure. Yes, some things were performed in an obscure way, but this is being done with the minimal amount of tools and supplies.
The main key to this is to take your time and do not cut any corners! I hope this helps and Good Luck!
All products were purchased from Z1 Motorsports.

Пікірлер: 121

@dannzx 4 жыл бұрын

don't forget to take the bolt out of the tensioner when the gap is set. very informative 🔧👍

@ZBruhzchannel 4 жыл бұрын

Yes this exactly!

@eekay3646 4 жыл бұрын

@@ZBruhzchannel And 4 mm gap...or roughly.

@eduardolabrador7705 3 жыл бұрын

damn it! the one time i dont check the comment section!

@johnmichaelkarma Жыл бұрын

Easy seal extraction tip. A small self tapping screw or drill small pilot hole then small screw inserted partway into seal. Lever under screw head with forked tack removal. The seals, where their rubber makes contact with camshaft and crankshaft should be lightly lubed with oil before insertion. 😎 I also had to replace the foam perimeter dust seals and some rubber bolt grommets on the timing belt cover. Pretty good vid and the paint and color combo is awesome.

@jeremythompson6822 4 жыл бұрын

Im here for the people who try to do this with the engine still in.

@slidewayskenny6925 4 жыл бұрын

same here, i wanna know how to do this with the plenum still on, aka holding the cam shafts in place while pulling cam gears off

@SoloKyoto 3 жыл бұрын

@@slidewayskenny6925 impossible, you have to remove the valve covers and in order to remove them you have to pull the plenum.

@SoloKyoto 3 жыл бұрын

@@slidewayskenny6925 actually not impossible but it would be Ridiculously hard and very very little room to get to anything with the engine still in the car.

@slidewayskenny6925 3 жыл бұрын

@@SoloKyoto false, i have already finished doing the full 120k maintenance including rebuilding the power steering pump and installing a new radiator. so therefore it is not impossible

@SoloKyoto 3 жыл бұрын

@@slidewayskenny6925 That's why I said it isn't impossible but just very hard.

@ghostsmoke11 4 жыл бұрын

THANK YOU for these amazing videos! You're adding so much to the Z32 community.

@ZBruhzchannel 4 жыл бұрын

You're welcome! Thank you for following the build!

@elibarnett4399 3 жыл бұрын

I watched your video on the stage two clutch replacement and I have to say it's the best video that I seen on line and it helped me out alot and in the future I will use your videos for a reference or help guide ,you guys made everything crystal clear and it made working on my 95 Z so much easier and understandable and made everything go off with out a hich. Thanx alot bro and you guys keep on your grind and stay up .

@vernonjackson6387 3 жыл бұрын

Great video guys. I needed the detail. Thanks for making me feel more at ease in doing my 120k service.

@ZBruhzchannel 3 жыл бұрын

Take your time and good luck!

@taipane-biensur7607 4 жыл бұрын

You guys keep anticipating everything I am doing on my car. You must have crystal ball of some sort- This was awesome. Thanks Robby and the team!

@ZBruhzchannel 4 жыл бұрын

Love it!!

@omarjalal4829 4 жыл бұрын

Awesome man!, You guys helped me out a whole lot with this video I was able to get my z back on the road thanks to you guys

@ZBruhzchannel 4 жыл бұрын

Love it!!

@customzdream Жыл бұрын

Awesome video. Very informative. Thank you men. It will help a lot.

@tobycarter4736 4 жыл бұрын

Great video! Really helpful

@crlrealty1 3 жыл бұрын

Great instructional video.

@erickarambula3494 3 жыл бұрын

That engines rocks those glasses real nice dude 👌

@AtiCrossfireX 4 жыл бұрын

The 300zx, is one of the easiest timing belts replacement. On any car I've ever done! The water pump is also separately, if you ever need to replace it. Nice video you guys 👍

@SoloKyoto 3 жыл бұрын

You have never changed one on a NA Miata then, I got to where I could do it by myself with no timing light or anything fancy in less than 45 minutes.

@JamieGuzmam 10 ай бұрын

@@SoloKyotoand you never done it to a 300zx😅😅😅😅😅😅😅😂😂😂😂😂😂😂😅😅😅

@SoloKyoto 10 ай бұрын

@@JamieGuzmam Also trust me when I say a Miata's timing belt is insanely easy in comparison to a Z32 300ZX.

@NbaMed 4 жыл бұрын

Best video I've seen for performing the 120k. Thanks!

@ZBruhzchannel 4 жыл бұрын

You're welcome!

@NbaMed 4 жыл бұрын

@@ZBruhzchannel literally about to do this to my TT motor on a stand, and the last belt I did was like 7 years ago. This video helped jog my memory lol

@ZBruhzchannel 4 жыл бұрын

@@NbaMed love it! Thats why we did it!

@ogm19881 3 жыл бұрын

Great video, when installing those cam seals I've always lubricated the seal before installing them almost the same as when you lubricate the oil filter seal before.

@ZBruhzchannel 3 жыл бұрын

Love it!

@AnthonyRodriguez-uo5hb Жыл бұрын

Good stuff , very helpful video, 👍

@KurtWinters 3 жыл бұрын

Great Video !

@cookies4life63 3 жыл бұрын

I picked up 92 tt about a month ago and I got everything from concept Z as well, first time doing a timing belt with a friend who knows more then me. Can’t wait to get my shit running after sitting for a few years

@ZBruhzchannel 3 жыл бұрын

Good luck!!

@elijahlundberg7934 2 жыл бұрын

This good stuff! Thank you.

@haycall 3 жыл бұрын

Good job guys!!!

@frog7118 Жыл бұрын

AC tension pulley bearing froze up and broke my AC belt. Watching this video around 39:10 showed me how simple it is to replace pulley, Just loosen the nut on the front and slide it out bottom of the slot. I got a used pulley off eBay and I just back off the adjuster bolt and slide the new setup into slot, snug the front nut, put on the belt to hold pulley in place, loosen nut and adjust to proper tightness of the belt. Thanks for a clear view of this assembly.

@ZBruhzchannel Жыл бұрын

Glad to be able to help!

@mnas964 Жыл бұрын

THANK YOU SO MUCH

@Junkitup 3 жыл бұрын

Robies da professional Thank you

@ElSesh 3 жыл бұрын

On the concept Z wiki it suggests for the tensioner to be 3.5mm - 5.2mm and you should rotate your engine 720 degrees twice and recheck the tensioner. You should definitely be good. Also my tension is always coming back to 5mm. I want to readjust to be within spec but I’m scared I may loosen the belt too much.

@tigwelding123 4 жыл бұрын

Nice info I have to do my timing belt

@shawnalbarghouthi4113 2 жыл бұрын

Thanks my dude

@ZBruhzchannel 2 жыл бұрын

Anytime!

@brotharuss 4 жыл бұрын

The spec is 3.5mm - 5mm. Note: A 4mm allen key is 4mm from furthest point to furthest point...so shoot for bareley being able to spin a 4mm allen head in the auto tensioner gap after two full crank sprocket rotations.

@Mario-et3tp 4 жыл бұрын

Wow im rechecking my timing after this video while it's still on the stand I didn't put the pressure on my tensioner when I tightened it

@ZBruhzchannel 4 жыл бұрын

Good looks!

@jeremythompson6822 4 жыл бұрын

Perfect time to do deletes, re-route coolant lines, replace valve covers and injectors upgrade pulleys to aftermarket.

@danmazz8733 3 жыл бұрын

Hi Jeremy, i just picked up a 90 NA, what do you mean by all this?

@jeremythompson6822 3 жыл бұрын

@@danmazz8733 Nissan overengineered the 300zx. You will need to do a lil research but whenever you have the engine out its a good idea to do all that

@mudaddy1 4 жыл бұрын

Thank you

@ZBruhzchannel 4 жыл бұрын

You're welcome!

@michaelbarrett8803 2 жыл бұрын

if you have the valve cover off you can just loosen up the camshaft end cap and remove the seal and put the new one in. If you do loosen the camshaft end caps you must put a little RTV on the base of the end cap.

@ZBruhzchannel 2 жыл бұрын

Thanks for the insight! I'll remember to do this next time!

@petrolwitch5940 3 жыл бұрын

OMG finally found this video been struggling and aligning cams ugh. Wish I would of searched for this sooner lol win some ya loose some am I right? But knowing is half the battle!

@ZBruhzchannel 3 жыл бұрын

Good luck with your build!!

@petrolwitch5940 3 жыл бұрын

@@ZBruhzchannel thanks mate! I miss driving the z32 so much its killing me

@ZBruhzchannel 3 жыл бұрын

@@petrolwitch5940 I believe it! I was without mine for a few months.

@petrolwitch5940 3 жыл бұрын

@@ZBruhzchannel think mines been down since about last March. Its my first time digging this far into a motor. So i am being as extra careful as possible. Already gotta fix a few wireing problems cause a few just decided to break when taking the harness off the engine...

@spicythai2000 3 жыл бұрын

I see alot of videos about the timing belt and they have the marks on the belt and the dimples line up. I used gates timing belt and it doesn't align perfectly but not a tooth off. So I kinda baffled how they have it so perfectly line up.

@Dpfdoctor 3 жыл бұрын

its no different doing it in the car if you pull the radiator people here saying its so hard with the motor in the car obviously dont have any experience working on these cars.

@nicolassantander1574 3 жыл бұрын

hi i have a nissan vg30det engine and i need spares. Where did you buy the spare parts? Could you tell me if the block is the same as the VG30DET AND VG30DETT? Thank you, have a nice day.

@zeda9253 Жыл бұрын

Aye I got a question about the intake cam gear. So I'm reinstalling it right now but when I was torquing it down the entire gear didn't move but the screw made this weird jump and now the cam gear after torquing it down is turned. I was able to line the markings back up to the back plate but idk if that fucked anything up. Do you know if the intake gear is fine or did I fuck up badly

@highoncoffe2330 7 ай бұрын

So I put the timing belt right where is need to be but the car won’t start only cranks

@codiehall5565 4 жыл бұрын

How would you go about removing a UR aluminum crank pulley? I got jaw pullers, but don't really like the idea of using one beings the aluminum is a softer metal then the stock steel crank pulley.

@ZBruhzchannel 4 жыл бұрын

I have used pullers for a while now and I believe to my knowledge that is the easiest way to go. Just make sure the teeth are on the pulley and be easy with it

@Mark-el3kz Жыл бұрын

Helpful video. After setting the tensioner gap to just under 4 mm, I rotated the engine 720 degrees, and the gap increased to just under 5 mm. Is this ok, or did I do something wrong? The gaps were the same after letting it sit for a week. Thanks!

@Mark-el3kz Жыл бұрын

Also, when I turned the engine back to the starting point for belt install, the tensioner gap was still under 4 mm there. So the gap ranged from just under 4 mm to just under 5 mm. I tried resetting the tensioner, but the gap range did not change. Is this ok or a problem? If it is not good, how do I fix it?

@GojiraZzz 2 жыл бұрын

There are two TDCs make sure it’s compression not exhaust stroke

@chefswole 2 жыл бұрын

do you have a video of your painting of the water pump? or is it simpler than I think? thanks!

@ZBruhzchannel 2 жыл бұрын

Very simple, just cover up the rear seal part with tape and the bearing part where the spindle is on and paint with high heat paint

@slidewayskenny6925 4 жыл бұрын

how would you hold the cam shafts in place if the plenum wasnt off?

@ZBruhzchannel 4 жыл бұрын

I mean people have made contraptions to hold the gears from moving etc, but it way easier by just taking the plenum off. We have a video on how to take it off if you need something to reference!

@tigwelding123 4 жыл бұрын

What's good

@Tastys14 Жыл бұрын

Hey man, I hope you can reply Where is the belt supposed to ride on the sprockets? After cranking a while, it ends up damn close to the backing plate. Not sure where I went wrong

@ZBruhzchannel Жыл бұрын

Belt should be, somewhat ride onbthe middle of the sprockets, depending on what belt you purchased (if not oem) it way be a bit wider.. Also the belt will somewhat center itself after a few rotations. I typally male sure as long as the belt is centered on the tensioner you should be okay

@J9irizarry 4 жыл бұрын

👍

@3lija11 Ай бұрын

For the crank shaft/ sprocket (I'm guessing that's what its called ,new here) at the very bottom @6:45 , i think you skipped showing the install of it , is there a video i can find for that or a forum on how its done? This is my first project car and i don't have any mechanic buds (im solo) Also your videos have been helping me a lot man thank you!

@ZBruhzchannel Ай бұрын

For the Crankshaft sprocket it's very simple, the only thing you want to really focus on is the washers that go with it. Once you put the washers in the correct area all you do is slide the sprocket on. Cleaning the crankshaft with a scotchbrite free of rust and lubing the inner race will help it go on smoothly.

@3lija11 Ай бұрын

@@ZBruhzchannel Awesome man your Goated, Thank you !

@fatimad4011 2 жыл бұрын

Do you happen to know how far apart the marks are ? I bought a belt but it doesn’t have any marks

@ZBruhzchannel 2 жыл бұрын

The belts should have marks on them. I highly advise not to put a belt on without the marks. These pints are crucial for proper timing

@johnpaulcooper5565 4 жыл бұрын

HELP!! My engine and transmission are still connected together inside the car. i was tempting to do the timing replacement and took tension off the belt but forgot to put the engine at TDC. so some how i put the belt back on with some tension and rotated the engine from the crank trying to get to TDC but then forgot that i should have put the car in neutral. so i was rotating the engine while it was in first gear and now for some reason i cant shift the transmission out of first to neutral to rotate the engine to TDC. ANY IDEAS HOW TO FIX THIS? HELP!!! @Z-BRUHZ AND ROBBIE

@ZBruhzchannel 4 жыл бұрын

First thing you should try and do is count the cogs on the belt while it is still on the car. I hope none of the gears turned on you once you removed the belt because that can and will be a huge issue

@danielZ32 3 жыл бұрын

@@ZBruhzchannel Sounds like he fudged up badly eh bro lol

@LuisDiaz-fc6ti 2 жыл бұрын

Where can I buy the 120 k service kit?

@ZBruhzchannel 2 жыл бұрын

Z1 motorsports

@davekelly7184 2 жыл бұрын

It has been mentioned that the bolt used to set the tensioner should be removed after final assembly, can you explain please?

@ZBruhzchannel 2 жыл бұрын

Once tension is set, you must take the screw out so it is not pushed out due to vibrations. If it is left in it will unscrew and damage the belt

@davekelly7184 2 жыл бұрын

@@ZBruhzchannel Thank you, would like to know it's purpose. He explained that he put approximately 15lb's of pressure on the belt before securing, so how does the bolt affect the tension?

@ZBruhzchannel 2 жыл бұрын

@@davekelly7184 the bolt is used to keep the tensioner from fully opening to its furthest point. It's a hydraulic tensioner. So once the proper amount of tension is placed and the spacing between the hydraulic pump is set and the the part is fully bolted down removing the screw will have the tensioner hold its position

@davekelly7184 2 жыл бұрын

@@ZBruhzchannel Brilliant. Thank you sir. I have owned my ZED for 17 years with very little use, so would like to change the belt before re commissioning her.

@ZBruhzchannel 2 жыл бұрын

@@davekelly7184 smart idea! Being proactive with these cars is very important

@rafaelcamacho1538 Жыл бұрын

Don’t know if anyone would reply at this point but I’m trying to adjust my timing tensioner and I set it to 4.5 and I tighten it it decreases to 3.3

@rafaelcamacho1538 Жыл бұрын

Some people say it should be good but I don’t wanna risk it not being spec

@ZBruhzchannel Жыл бұрын

@Rafael Camacho is it a Nissan oem part? And if it is the best way to set it is by following the process and using a prybar to help set the tension

@rafaelcamacho1538 Жыл бұрын

@@ZBruhzchannel I believe it should be I bought the 120k timing service kit from czp the only difference compared to yours in the video is it has hex bolts

@rafaelcamacho1538 Жыл бұрын

@@ZBruhzchannel also I put tension using the pry bar just slight cause it feels really tight and it’s good but once I tighten down the bolts the gap just continues closing

@user-od2mx5pf4d 9 ай бұрын

Who makes the exhaust headers that you are using?

@ZBruhzchannel 9 ай бұрын

They were a company called DNA, unfortunately they are not around anymore

@user-od2mx5pf4d 9 ай бұрын

Thanks@@ZBruhzchannel

@davidkite4750 2 жыл бұрын

You forgot to mention to remove the adjustment bolt from the tensioner after the tensioner is set!

@ZBruhzchannel 2 жыл бұрын

When filmed I believed it was a common sense thing to do, but I pinned the comment of that to be showed first just in case people did not know.

@GBiv78 Жыл бұрын

Are you literally saying the only way to pull the camshaft sprocket is to split it in half?

@ZBruhzchannel Жыл бұрын

No, there are other ways such as drilling and tapping two holes then use two bolts to help pull it off. We have found it much easier to cut and get rid of if there is rust.

@jeremythompson6822 4 жыл бұрын

First.