Acura Honda Classic TL Type-S Build Project - Replacing Manual Clutch Part 2 ( Episode 8)

Рет қаралды 21,437

4 жыл бұрын

In this Part 2 episode of this series, our team will be cleaning all of the used clutch material for the transmission housing by using Brake Cleaner and Purple Power greaser. Then we will be installing the new throw-out bearing and flywheel pilot bearing along with the OEM pressure plate and clutch disc. by using a special Honda clutch alignment tool. Finally we will be reinstalling the manual transmission. As always, tips and tricks come standard.
OEM Part List and Number:
Clutch Pressure Plate and Disc Assembly: 22105-RDB-315
Flywheel Pilot Bearing: 91006-PGE-008
Release Bearing: 22810-PPT-003
Release Folk Boot: 22841-PPP-000
Rear Main Seal: 91214-RCA-A01
Rear Main Cover O-Ring: 91308-P3R-T01
On the next Part 3 episode, we will be working on the leaking power steering system by rebuilding the power steering rack and pump. Lastly, we will be also cleaning the engine subframe and it came out like brand new. Stay tuned for next week.
Acura Honda Classic TL Type-S Build Project Playlist:
• Acura Honda Classic TL...
🔔 Subscribe for more free KZfaq "Tips and Tricks": / @ahcgarage
If you have already, please follow us on Instagram to see sneak peaks ahead of time!
Thank you to our exclusive sponsor: Acura of Pembroke Pines
www.acuraofpembrokepines.com
Follow us on
Instagram: @AcuraHondaClassic
Facebook: Acura Honda Classic
Acura Honda Classic established in 2018, is a group of Acura/Honda enthusiasts set out to bring together the car community through Acura/Honda vehicles of the 80s, 90s and today. We strive hard everyday to "Building Our Community". Follow us on IG @AcuraHonda Classic to stay up to date on our news, events and activities.

Пікірлер: 89

@accuratein04 3 жыл бұрын

I wouldn't mind driving down there and letting you guys service my transmission just like this.

@Steeda04SVT 2 жыл бұрын

was thinking the same thing.

@JohnWD40TC02 3 жыл бұрын

Watching you folks fit a new clutch in Brian's car made me think when I used to do it with just a pair of ramps that raise the front wheels, my car was an old 80's Ford Cortina RWD so the box was huge and heavy laying on your back trying to disengage the prop shaft from the rear of the gearbox and the gearbox shaft from the clutch housing, all I had was a shaved down broom handle to realign the clutch to the pressure plate, those were the good old days. These days I take it to a garage 😂 John UK.

@ahcgarage 3 жыл бұрын

We got it good these days. Thanks for sharing your story John

@aaronnealey488 Жыл бұрын

Well that’s it 3 Guys and one Trainee . 😂

@ahcgarage Жыл бұрын

Haha!!

@owhite97 3 жыл бұрын

I have a 2015 accord 6-6 and i got the oem clutch flywheel and rear main plate with the seals already installed in them nice TL super clean

@younginng3661 2 жыл бұрын

Love the content!! Mad that I barely discovered you guys a few days ago through YT recommendation. A 4th Gen Honda Prelude project would be dope!!! Preludes usually get no love.

@ahcgarage 2 жыл бұрын

Welcome to the channel

@triniemperror 3 жыл бұрын

Damn, why couldn't you guys just be in MD. My 2005 TL clutch is slipping really bad but I'm hesitant to take it to the dealership. You guys did such a pro job

@hangrymachinist 4 жыл бұрын

Great videos. I just bought a 2005 TL with a 6 speed and I am finding this very helpful. Keep up the good work

@ahcgarage 4 жыл бұрын

Congrats on your new purchase and thanks for your support

@hmoob-dab-tsi7572 3 жыл бұрын

Clutch work isn’t that hard. Finding enough under work space is harder. Not sure why the subframe was removed but it didn’t seemed necessary

@LedSledJoe 2 жыл бұрын

Howdy again! Just finished watching some more videos. Love what you got going on. HQ videos, clean, well shot, clear instructions. WOULD LOVE TO KNOW a thorough list of tools used by the Pembroke boys used for each task on the TL. Tools really help the job go much easier! (and of course a lift!) THANKS

@mercenary2318 9 ай бұрын

My car needs this. And i honestly dont trust anyone to do a good job around my area doing it. Mechanicphobia here

@fixitjose9780 4 жыл бұрын

👌🏽👌🏽👌🏽👌🏽 was waiting for this to drop

@ahcgarage 4 жыл бұрын

👍🏼👍🏼

@jakemckeown9961 3 жыл бұрын

3 guys and 1 trans! I died laughing. Lol

@ahcgarage 3 жыл бұрын

Haha. It was great!!

@kseries20-24only 4 жыл бұрын

LOVE these videos! I've not found anything really going through a rear main seal repair. I may need to chase this on my 05 RL. Food for thought, videos with anything on RL since they are less common but so much potential. Also I have an TL in addition to the RL and evaluating a supercharger for one of them. Would LOVE to see something on superchargers on J-series to help me decide if/where to put one on. I love my SH-AWD but really want some more torque. Supporting you guys fo sho!

@ahcgarage 4 жыл бұрын

Thanks for your support and the great suggestion. We will put that on our to-do list

@vteckillerfa5 4 жыл бұрын

💪💪💪 Making progress papi!!

@ahcgarage 4 жыл бұрын

vteckillerna1 yes sir

@blackr2001 4 жыл бұрын

Awesome guys

@ahcgarage 4 жыл бұрын

Thanks for your support 👍🏼👍🏼

@stevenngo4557 4 жыл бұрын

Should use factory tool to place pressure onto the clutch assembly before being torque. This is a self adjusting clutch. Keep up the cool videos

@ahcgarage 4 жыл бұрын

Great point!

@GS-sm3jo 3 жыл бұрын

AHC always keeping it 100% with OEM parts👍🏻

@ahcgarage 3 жыл бұрын

Yes sir

@mercenary2318 9 ай бұрын

Wish you guys could do mine

@bikgarcha3061 Жыл бұрын

Hi AHC garage, quick question regarding the self adjusting clutch tool. Did your team happen to adjust the clutch with the tool? Or did your clutch arrive pre-set/locked at the required specs?

@unfilteredjamaican3478 4 жыл бұрын

Do you guys have any experience using BG product additives for engine performance, motor oil, ATF, and or fuel cleaner? Of course, when used in conjunction with genuine Honda/Acura fluids. And what is the best (suggested) online OEM parts supplier for Acura?

@ahcgarage 4 жыл бұрын

This is a tough question since everyone will have their own views. As for any additives, Acura and Honda do not recommend them in any of their vehicle at all. Due to the increase ethanol level in fuel, we do see some increases of carbon build up in the combustion chamber. Some mild induction products and fuel additive can help to clean out the carbon build up.

@shlumpgod 2 жыл бұрын

Probably gonna have to just deal with my leaks since i have a jerky transmission. If i get another car I’d definitely come back to this video to remove my transmission. Hope you guys slowly but surely begin to expand in the future. Also, what tool did they use for the tie rods???

@ahcgarage 2 жыл бұрын

We are loving the growth so far. As for the tie rod end, do you mean the tool to pop off the joint?

@shlumpgod 2 жыл бұрын

@@ahcgarage Nice and yeah so I wouldn’t have to bang it with a hammer lol

@truejey7475 3 жыл бұрын

How much does it cost to change the rear main seal?

@nestornarvaez8416 9 ай бұрын

hello sir where i can buy the alignment tool u guys got

@MrMountainHawk 3 жыл бұрын

What was used to pull out the throw out bearing looks like that wasn't shown on video. But another great video as usual.

@ahcgarage 3 жыл бұрын

The throw out bearing just slide out from the arm

@gavinkeogh6590 Жыл бұрын

Nice video! One question: is it not necessary to use the pressure plate compressor tool to install it? Thanks.

@ahcgarage Жыл бұрын

We did not use that tool

@tucha1942 3 жыл бұрын

Great Job Guys. I"ve watched this video about 5 times already trying to build my confident in changing the clutch on my TL. I have 1 question. Did you guys change the flywheel bolts and did you guys put the red loctite on the bolts? I read some forums and everyone has different opinions on it. Some say to change out the bolts and some say you don't have to change it, just put some red loctite and it should be ok. What did you guys do?

@ahcgarage 3 жыл бұрын

Thanks for watching and support. The bolts are reusable. A small amount of lock loctite can ensure the flywheel bolts not back out.

@supersabrosinho 3 жыл бұрын

Just like you I'm also debating doing this job myself on my 4th gen SH-AWD 6MT. I also had some anxiety cuz all info online said that Loctite is required. For example, all forums swear that if you don't put Loctite on the propeller shaft bolts it will loosen and pole vault your car into the next highway. I just torqued my propeller shaft bolts (reused) and so far no pole vaulting. Let me know how your clutch job went 👍

@woodnoober2363 2 жыл бұрын

@@supersabrosinho did you do just an oem clutch and how’s it been holding up for you?Because I’m thinking about doing my own also with a friend

@supersabrosinho 2 жыл бұрын

@@woodnoober2363 yeah OEM is the best for the 4th gen TL. The job was tough. It's probably easier to remove the whole engine/trans from the top instead of dropping the subframe. Good luck

@truonghthe 4 жыл бұрын

2 question for you guy. 1. Any reason why you guy reuse the flywheel without resurface or replace the flywheel? 2. I though the pressure plate will need to be set to the max point, where the small spring should be below the green mark, since this pressure plate is adjustable. Thanks for th video as my previous owner already perform this service on my KBP.

@ahcgarage 4 жыл бұрын

1. The original flywheel is within the service limit so after we checked it with feeler gauge so there’s no needs for resurfacing or replacement. Beside, a new dual-mass flywheel is a very expensive item. 2. We left the spring at the same position on the pressure plate Thanks for your support 👍🏼

@truonghthe 4 жыл бұрын

@@ahcgarage the dual mass not that expensive.... ONLY $950 lol... Thank you for providing the info.

@maxdiputs2863 2 жыл бұрын

Hello and thank you for the video. I just had a quick question since you guys are so thorough and use a lot of special honda tools. Did you all use the Honda Pressure Plate Compression tool or is it not necessary? Thanks!

@ahcgarage 2 жыл бұрын

Not necessary

@koriseitz2629 2 жыл бұрын

@@ahcgarage why is it not necessary? They are self adjusting for a reason. Not resetting those can cause premature failure on a new clutch.

@jackmraz4037 2 жыл бұрын

@@koriseitz2629 I think it's more an issue when reinstalling an existing clutch but not as necessary for new installs

@koriseitz2629 2 жыл бұрын

@@jackmraz4037 negative. It’s necessary all the time. Used or new. Many of the aftermarket pressure plates don’t come adjusted.

@bigef9395 3 жыл бұрын

was wondering when installing a stage 2 clutch from luk after full install everything u just did i did but wont go into gear and ideas???

@ahcgarage 3 жыл бұрын

Check your hydraulic system operation, clutch mater and slave cylinders

@marcoshernandez2839 2 жыл бұрын

What year is this ??

@Gonzoe714 4 жыл бұрын

Hello I am looking to do this in the near month can you possibly provide me with part numbers for the clutch and seals

@ahcgarage 4 жыл бұрын

All parts are listed under the description

@toastranger72 2 жыл бұрын

How do you get the pressure plate on without loosing the SAC adjustment? A shop did my clutch, and it engages right off the floor. There is nearly no travel. You feel it start to catch, and it's fully engaged. My throw out bearing is already shot because it must have never fully released. The garage wants to brush me off.

@ahcgarage 2 жыл бұрын

Cheers!!

@toastranger72 2 жыл бұрын

@@ahcgarage That was really helpful. Thanks

@Rois300 2 ай бұрын

What??? What did john and miguel do at 14:15 to the clutch fork?

@ahcgarage 2 ай бұрын

The release bearing folk snapped into place

@NonstopAutoRepair Жыл бұрын

Care to share what degreaser is it you sprayed on there?

@ahcgarage Жыл бұрын

Brake cleaner, here's the link: amzn.to/2WNq353

@davidmartinez391 4 жыл бұрын

Are you guys planning to have a car show

@ahcgarage 4 жыл бұрын

David Martinez Yes, our next meet is about a week away, 03/15/20 from 8-11am at Acura of Pembroke Pines

@Kwasial 4 жыл бұрын

what brand is that magnetic light

@ahcgarage 4 жыл бұрын

Matco

@hyden1532 3 жыл бұрын

How would you be able to tell if you rolled the rear main seal?

@ahcgarage 3 жыл бұрын

Once installed, the inner lip of the rear main seal should wrap around the crankshaft end

@supersabrosinho 3 жыл бұрын

What ahc garage said.A massive puddle of oil under the car would also be a great indicator 😄

@ahcgarage 3 жыл бұрын

Ha! Yes indeed

@Hibachipower 3 жыл бұрын

when the video start at 2:50 ,,, i saw that what is it for cleaning the surface......??

@ahcgarage 3 жыл бұрын

Brake cleaner

@Hibachipower 3 жыл бұрын

@@ahcgarage what about the rear main seal ? Install it dry is okey??

@ahcgarage 3 жыл бұрын

Yes

@Hibachipower 3 жыл бұрын

@@ahcgarage thank you

@mercenary2318 9 ай бұрын

Did you reuse the old flywheel?

@ahcgarage 9 ай бұрын

Yes we did

@mercenary2318 9 ай бұрын

@ahcgarage you know what brand of clutch come stock w the acura. I need to do mine. I just purchased a luk kit. The only dual mass flywheel i can find if from acura. And its 2,000!$ i dont think i can swing a new flywheel . My TL is 2012 with 104,000 miles on it

@hmoob-dab-tsi7572 3 жыл бұрын

I remember b series flywheel has way more bolts

@ahcgarage 3 жыл бұрын

Both B-series and TL-S are 8 bolts for the flywheel

@hmoob-dab-tsi7572 3 жыл бұрын

@@ahcgarage I haven’t looked in a B series transmission in a long time. Probably time to work on the clutch of my 05 tl 6speed. 189k miles, will be needing timing belt, all bushings replacement.

@ahcgarage 3 жыл бұрын

Take your time and you will be fine