Adding Brakes to All Four Tires! - Off Road WheelChair

Рет қаралды 579,644

5 жыл бұрын

Safety is in our top 5 priorities here on JerryRigEverything, and that Includes adding brakes to both the front AND rear tires at the same time. Stopping power is ALWAYS a good thing. Here is the lever we used: amzn.to/2FGf4Ru it pulls both brake cables at the same time. Let me know if you have any more suggestions!!
With the cable disk brakes working on all four tires, Cambry will be able to stop sooner, and have more traction on slick, or gravel surfaces. Bring on the snow.
Watch the reveal as we give it to Cambry HERE: • Homemade Off Road Elec...
Watch how we made this bike: • How to Build an Off Ro...
Protecting bike tires against thorns: • How to keep Fat Bike T...
Off Road WheelChair Climbing a mountain: • Off Road Wheelchair Te...
Check out Cambrys Instagram HERE: / cambrykaylor
Let me know if you have any questions in the comments!
Customize your own Tesla Here: ts.la/zack10701
The camera I used to film this video: amzn.to/2p7GtkX
The Lens I used for this video: amzn.to/1QOXDw2
Wide angle lens: amzn.to/2qiYM4u
And this Metabones adapter: amzn.to/2iZ67Ty
This is the drone I use: amzn.to/2joH00G
Music is from HERE: share.epidemicsound.com/pcGGf
Follow me for updates!
Instagram: / zacksjerryrig
Facebook: on. 1U4bQqv
Twitter: / zacksjerryrig
Snapchat: bit.ly/1UAb2Fq
GooglePlus: bit.ly/1YyKice
TO SEND ME STUFF: See my P.0. Box on my 'About page': / jerryrigeverything
JerryRigEverything assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. JerryRigEverything recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of JerryRigEverything, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not JerryRigEverything. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.

Пікірлер: 1 400

@WhatsInside 5 жыл бұрын

Zack never let me say “let’s get started” 😞

@kunalfindley158 5 жыл бұрын

LMFAO. Bruh, I watch your channel all the time man, keep up the good vids

@AliYassinToma 5 жыл бұрын

Cuz u aint a girl bruh

@daksh.sharmaaa 5 жыл бұрын

What's Inside? Check out mu channel and tell me how is it according to a kid

@srengoul860 5 жыл бұрын

SAD

@cularu1 5 жыл бұрын

Want a kiss now?

@YosefB 5 жыл бұрын

It would be safer to have the two front brakes together and the two back brakes together. Less risk of flipping over the front.

@ReN-tw6mb 5 жыл бұрын

Ya, I agree with you on that one.

@CookedPorkchop10 5 жыл бұрын

Just what I was thinking as well

@FFM0594 5 жыл бұрын

No risk if the braking is set up correctly.

@QAnyui 5 жыл бұрын

@@FFM0594 there is. If she gives different pressure on one side, one side will be slower than the other side, which make the wheelchair to slide to the side

@QAnyui 5 жыл бұрын

Yup. Someone explain it better than me.

@whodis113 5 жыл бұрын

So collective ideas from the guys below: 1. marry her 2. separate front brake and rear brake for better braking modulation, especially during downhill descending. 3. from the previous video: tubeless for better puncture-resistant, light-weight, and better mileage 4. Switch from Mechanical disc brake to hydraulic --> better stopping power with less force applied 5. Rear shock-absorber 6. This is just my 2 cent but.... can we do something about reversing? if it's a conventional wheelchair she could easily back up, but since this is a motorized version, it's kinda tricky :-? 7. Reflectors, front n rear, easiest way? slap some reflector tape on it. 8. put a helmet on for her since she's a speed demon lol 9. Parking Brake maybe? 10. Marry her.

@GamingAmbienceLive 5 жыл бұрын

if he doesnt marry her hes just toying with her heart and will be the biggest douchebag on the internet, hes a nice guy, but he is kind of raising this girls hopes up if he has no other plans, unless he has a gf that nobody knows about, or is married, or is gay, he is way too alpha _not_ to marry her otherwise, and should do it, hope she can really have kids

@DeaThlyShaD0w 5 жыл бұрын

@@GamingAmbienceLive In video about idk. Some kind of foundation, she told that she can have kids..

@GamingAmbienceLive 5 жыл бұрын

i know I watched it, i just dont know how true it actually is, maybe its something they told her to keep her hopes up, truth is nobody will know until she tries

@DeaThlyShaD0w 5 жыл бұрын

@@GamingAmbienceLive I don't think that they lied her.. I hope everything's ok..

@DennisCrouse 5 жыл бұрын

All great suggestions, I am very partial to #1, and #10

@joshnicoll6761 4 жыл бұрын

I've been binge watching the electric wheelchair videos with a massive smile on my face. Zach you are one of a kind. And side note you guys are the goals of couples .

@QAnyui 5 жыл бұрын

What about making one side of lever is for front and the other are for rear brake? Because if she puts a different braking force on one side, the wheelchair could be unstable since, as an example the right side stops quicker than the left side. Sorry for my English but I do hope you get the idea

@cbr7170 5 жыл бұрын

great idea

@rajeevarts398 5 жыл бұрын

Yah !! Good idea

@adarshkrishna6434 5 жыл бұрын

Exactly what I was thinking. With this installation one lever will hold one side. That doesn't feel safe enough if Cambry has to stop on a slope or something.

@DanijelBre94 5 жыл бұрын

I thought the same, adding those brakes is stepback.

@pebamag 5 жыл бұрын

I though exactly the same thing

@karkiabhishek 5 жыл бұрын

*1.* Why didn't you put the brakes facing downwards? *2.* Use one lever for front brakes and another one for rear brakes.

@ZacksJerryRig 5 жыл бұрын

We wanted the handle bars to be as low as possible. If the brake handles were below the handle bars, they would clip the frame.

@mitchellhuse993 5 жыл бұрын

Abhishek Karki she might have small hands

@karkiabhishek 5 жыл бұрын

@@ZacksJerryRig Oh! Ok. Thank you so much for replying to my comment.😊😁

@rbching3535 5 жыл бұрын

@@ZacksJerryRig you can actually get an inexpensive riser bar, split it into 2 for the left and right and have clearance and a symmetrical setup.

@derekfester6084 5 жыл бұрын

ZacksJerryRig what about on the outside

@TheDudeman523 4 жыл бұрын

I have no words for how much respect I have for you after watching everything you have done for her. Quality of life is everything for someone in a wheelchair. I wish I could have done things like this for the people in my life that spent many years in a chair

@chrissjogren6843 5 жыл бұрын

Zack just need to tell you, you are a true inspiration for so many people . You highlight problems and help the ones that's really needs it. You seems very humble and kind. You are also very cost conscious, which I like. You are, at least for me . A true role model. You have teach me so much with your other channel, to fix things. No I offer friends and family to fix the old broken tech instead of throwing it away, Or at least make a try to fix it. Keep up the good work! Annnnnnd I got a iPhone without a headphone jack... sorry :D

@jmerced 5 жыл бұрын

Love watching you guys. Most people don't realize how expensive something like this would be if it were made by one of the few wheelchair companies. I never subscribe, and I just did. PS. You guys are great together.

@tinamoul 4 жыл бұрын

It wouldn't be that expensive, prototyping something always costs more.

@XSpImmaLion 5 жыл бұрын

Few more episodes 'till it turns into an exoskeleton robot hybrid.

@kunzklingsor9156 5 жыл бұрын

She loves him. Who would not adore a human being so kind? This is movie material. Kudos.

@d1v1s1onby0 2 жыл бұрын

Hi - A couple of suggestions. 1. Fill tyres with water - I do this with my tractor, it adds weight right where you need it most for better traction and roll stability. 2. upgrade to front hub motors in addition to the rear - run them in parallel with the same controllers and give you 4 wheel drive. 3. If you go with front hub motors you could flip one front wheel backwards (Reverse the tire so it still looks "right") connect the flipped wheel separately onto a different accelerator mounted by Cambrys' hip. This would take you down to 3 wheel drive going forwards but you would gain a rudimentary 1 wheel drive reverse.

@JaysonDionisio 5 жыл бұрын

Do a collab with Seth's bike hacks. It'll be awesome. 🤙🏼

@hsb14214 5 жыл бұрын

Yeah... Seth's a little out of order

@nathanielvogler7335 5 жыл бұрын

All the more reason, it will give Seth something to do.

@alaricloftus6277 5 жыл бұрын

Yes! that would be so cool

@caydenfeemster5191 5 жыл бұрын

He could clean up that cockpit so you cant see cables

@gdevansh 5 жыл бұрын

Yes!

@BraxenMcConnell 5 жыл бұрын

I think it DOES matter what hole it goes in

@De__Niro 5 жыл бұрын

LOL

@mo_is_out 5 жыл бұрын

Yes officer this comment right here

@CRIZZZLPT 5 жыл бұрын

Well, not like she is gonna feel it anyway.

@chickenray182 5 жыл бұрын

Depends on the night.

@ch.illmatic 5 жыл бұрын

Nah, stick it in any

@alucardat4929 4 жыл бұрын

You are a man with a big and kind heart. I wish you happiness. Regards from Odessa, Ukraine)

@abdullafarid3202 5 жыл бұрын

The off-road wheelchair is currently my favourite thing on the internet! Great work. I always respected your hard and beautiful work and inspired me to take apart cellphones and so on, but this is a whole new level! Thank you really! And to make Cambry experience something she never dreamt of is priceless actually! So huge thumbs up for you and all best wishes for her to enjoy this ride safely! Just a small note, I think it’d be better if each handle controlled the same tires ( one for both rear and one for both front tires ) I mean it is safer ( to avoid spinning in high speeds ) and easier ( since you don’t have to use both of them all the time ) It would require an extra long brake wire but it won’t be difficult to you! And it’s worth the extra work, believe me.

@benedictschmieder7249 5 жыл бұрын

I would suggest hydraulic brakes. They are a little bit harder to install, but the force reuqired on the lever to stop the bike (especially with this heavy one) is lower. It's also relativly simple to get the oil flow to all brake cylinders. Oh and I would also suggest to use bigger brake discs, since the mechanical advantage through the leverage is bigger with those :) If I made mistakes, please excuse them, I'm from Germany and my English is a bit rusty since my degree :)

@KB-mo3sx 5 жыл бұрын

And if you use roughly the same length of hydraulic hose the pressure in the brakes should equalize, and it means that the brakes should break equally even if one of them has less breaking pads.

@ROG-ht5cz 4 жыл бұрын

Deine Englisch ist perfekt, nicht wie meine Deutsch 😂

@UTMopar 3 жыл бұрын

Hope makes hydraulic brakes where one lever works two calipers. In this case, one lever one each handle bar and they could operate brakes on all four wheels. Unfortunately, Hope can be expensive.

@cvspvr Жыл бұрын

dein Englisch ist Super!

@BasketCase 5 жыл бұрын

Really important safety / control aspect.... Same as many comments below; FRONT BRAKES ON ONE LEVER REAR BRAKES ON THE OTHER LEVER

@stanfordcoffee 5 жыл бұрын

As it sits, you have vehicle set up to break left and right, which has the potential to cause instability. Reroute the cables so the back are on one handle, and the front are on the other. Cheers

@larryhawkes1347 4 жыл бұрын

Thanks for taking care of this beautiful young lady and providing her this kind of freedom to get around in so many more places than normal.👍

@petarau9514 5 жыл бұрын

another day, another vid by Zach. life's goooood

@BJMTM1 4 жыл бұрын

Man you two would be so perfect together the way he looks at her makes my heart melt

@No1sonuk 4 жыл бұрын

They're married now.

@tracerandom7082 4 жыл бұрын

Bruh😂

@robertmashburn8330 4 жыл бұрын

I’m excited for this couple. Such an inspiration. 🌺🌸

@moveaxebx 5 жыл бұрын

Zack, in most profound way, she is something special. God bless you both.

@airmarshalls538 5 жыл бұрын

Good too see what your doing for this woman!! Good Shit Zach

@Roseneck12 5 жыл бұрын

Put a ~90% angle on the handles. make them into joysticks or pistol grips or like a pod racer. That will give her a firmer grip on the controls and more confidence. You can take what you have now just cut and weld them at an angle no big mod needed.

@rodrissanen7047 4 жыл бұрын

Thank you Zack for that link, my 1-arm ebike riding just got a whole lot easier once I get that lever.. In one month I've put over 850km on the bike, works so well..

@sammhill8686 5 жыл бұрын

What a heartwarming video series. Thanks for letting us share the joy.

@tmworld3385 5 жыл бұрын

The way Jack looks at her says it all #jack is in love

@tomhoblin4571 5 жыл бұрын

"Getting it on is a little bit easier than getting it off"

@bxbLJ 5 жыл бұрын

Getting it on usually gets me off

@WaneesMeftah 5 жыл бұрын

zack 2018

@ryleyt3752 4 жыл бұрын

Literally paused it right after he said that to search for this comment. Was not disappointed.

@gregozo 4 жыл бұрын

Zack, kudos man for being so creative and inspirational to us all. Keep on going!!!

@simongreaves210 4 жыл бұрын

You Two. Made for each other. It's Lovely.

@redredredred2 5 жыл бұрын

1, change the handle orientation make it more ergonomics. 2, control both motors with one hand. 3, left hand control both rear brakes, right hand control both front brakes, or one handle control all 4 brakes. 4, self get in with the chair redesign, maybe combine with a wheelchair rolling in and lock together.

@fasfan 5 жыл бұрын

You could install some sort of limit switch on the brake lever that interrupts the power. That way she wouldn't have to remember to release the throttle when braking.

@StreetMachine18 5 жыл бұрын

Nice job filming, Cambry!!! You guys rock!!!!

@heikowolf2361 4 жыл бұрын

Zack, this build is pure love

@anishekchaudhary 5 жыл бұрын

You could flip the break levers (rotate 180 degrees) so that rider can apply the brakes using fingers instead of thumb which is more effective :-)

@Coolwoo 5 жыл бұрын

Sorry to point out the way you’re putting it, you’re implying that the thumb is more effective. Is that what you intended to say?

@anishekchaudhary 5 жыл бұрын

@@Coolwoo No, I ment to say that index finger is more effective

@FranseFrikandel 5 жыл бұрын

Looks like that would collide with the top tube of the frame.

@No1sonuk 4 жыл бұрын

He responded in another comment: "We wanted the handle bars to be as low as possible. If the brake handles were below the handle bars, they would clip the frame."

@Wetkeazle 5 жыл бұрын

You didn't mention one cool feature of the brake handle: the parking brake. When you engage the brake and push the button on the back , it locks the brake until you engage the brake again. Then the button pops up and releases the cables.

@krymera 4 жыл бұрын

Nice job, but I do have some suggestions. 1. Add lights In the Handel holes where you saw off the other side of the Handel 2. Add plastic covers at the wheels for wet weather 3. Safety belts if there is an accedent, she won't fly off the seat. 4. Emergency safety lights (parking lights) that people (drivers) can see her in the later hours when she is "standing" still. 5. Parking breaks, as you have mentioned in the previous video. That's it for now, keep up the good work.

@speedbuggy16v 5 жыл бұрын

awesome, glad there was an off the shelf solution for the brakes!

@laughingman3777 5 жыл бұрын

Dude, you totally have a crush on her.

@deltavee2 5 жыл бұрын

Is he Mormon too?

@laughingman3777 5 жыл бұрын

@@GamingAmbienceLive Finally, somebody that gets it. Also cool handle lol does Cody know you're using it and that you have such a twisted mind? Let's be friends

@GamingAmbienceLive 5 жыл бұрын

lol he definitely does because i make some controversial comments all over youtube lmao, including his videos, lets

@archiball7954 5 жыл бұрын

she totaly digs him(":

@reoflex 5 жыл бұрын

So do I. She’s a doll. And a soft spoken woman! Very desirable. They should all be soft spoken. Contrast her with a lesbian feminist foul and nasty, man hating loud mouth!

@randomodbuild 5 жыл бұрын

If possible, you should put both rear brakes on 1 lever and both front brakes on another. This will make it so she can hit both rear brakes with one hand, giving more stable braking without worrying about having to hit both brake levers at once. It may take extra long brake cables (you can tie them across the steering bar) but it will add a lot of stability.

@allenwaters96 5 жыл бұрын

Adding curved tube rails that connect seat-post (bike) to top of center seat tubes would allow her grip areas for side entry. Adjusting camber may also improve stability. Quick disconnect for steering control will allow her to enter from the front. Maybe a molded seat for her "Altera-Chariot". I love what you've done, please keep it up.

@davidmiracle398 5 жыл бұрын

A good video. Your delivery is smooth and informative. This wheelchair is very innovative and thanks to the two Rad Rovers is made with good parts and should hold up over time very well. Thank you for all the time, energy, and skill, that went into building the wheelchair and in the making of the video.

@TheFourthWinchester 4 жыл бұрын

Zack: "Getting it on is a little bit easier than getting it off" I'm glad he did good.

@kaiindra637 5 жыл бұрын

Looking for all the "is that your girlfriend" comments

@jimhorrace6026 5 жыл бұрын

lol me too

@Max-zp9xv 5 жыл бұрын

Why who cares if it is good for him

@audreandre 5 жыл бұрын

nah i look a comment "marry her" tho

@paradonym 5 жыл бұрын

I'd guess it's one of jerrys girlfriends - of course - you see it... but it's probably one out of many.

@ross-carlson 5 жыл бұрын

@@GamingAmbienceLive Sadly, no - they are both cultists (Mormon) so that's not happening sadly.

@smiffy5075 5 жыл бұрын

You two make such a great couple! I'm so happy for you guys!

@projectconsultant7174 4 жыл бұрын

Apart from Jerry Rig Everything. Jerry and Cambry are the cutest couples. I adore them. Jerry-builds an electric custom bike for cambry. I could feel cambry is emotional. But they don't show that cry part or anything. They keep their precious moment personal. Love that. Thank you for inspiring millions around the world. Hats off and like cambry say " Kudos to you guys". Work you guys doing in Kenya is amazing. If I have request, jerry should explore a project on less expensive or more afford mobility gears for a special need people and review it and rig it and make it better. 2020 I wish you guys more success, love and everything that you wish for.

@HerrMarcoPolo 5 жыл бұрын

Cambrys why you don't have your own KZfaq channel? You are amazing woman! ❤️😉

@adityabaradia3675 5 жыл бұрын

Sir it would be safer if you put front brakes on one Lever and rear brakes on another..

@rambor-rgaming2535 5 жыл бұрын

nope. because it kinda acts like abs.. because breaking force is applied same way. and it'd be more difficult to opeeate your way it'd be less fun

@xavierazad 5 жыл бұрын

@@rambor-rgaming2535 Imagine if you pressed brakes and one side of your vehicle stops moving and the other doesn't.

@MrClarkisgod 4 жыл бұрын

@@rambor-rgaming2535 Not at all. If you are sliding down a hill the last thing you want is to lock up only one side of the brakes. It could cause it to pull hard to one side... and off the side of the hill you go. Much, much safer and easier on the user to have both fronts and both rears on their own handles.

@Gilespargiter 4 жыл бұрын

@@xavierazad Like a skid steer loader or tracklayer it would spin on it's own axis. Definitely not something you want to do at any speed, it will throw you over.

@xavierazad 4 жыл бұрын

@@Gilespargiter Exactly.

@yatharthagarwal2041 5 жыл бұрын

Love the way she says let's get started😍😍

@valprem6401 5 жыл бұрын

Love the fact kambry is on the show again!!!

@MichelPostma 5 жыл бұрын

I never knew about those double brakes! Btw, it seems like the rear lights need to be turned on manually? Maybe connecting them with the front lights or using a dynamo//battery with light sensor would help? I know we have some in Holland for our bikes, but its been ages since I have used them

@enfentonk 5 жыл бұрын

She's becoming a pro at the intro

@pauldegennaro7798 4 жыл бұрын

Awesome patent that thing . Don't let someone else take your fire. It looks like a lot of fun . Look at her smile when she rides. !.

@sparky2059 4 жыл бұрын

AWESOME job Zack , Very cool

@FFM0594 5 жыл бұрын

Maybe she just wants flowers.

@ZacksJerryRig 5 жыл бұрын

Well... she got a four wheeled monster electric fat bike instead.

@JacobTechShit 5 жыл бұрын

ZacksJerryRig you clearly have a crush on her... just get her some roses instead of spending 500 African kids yearly meal budget on a wheelchair

@Elias_g1 5 жыл бұрын

@@JacobTechShit WOW,this is rude !

@Zarrar2802 5 жыл бұрын

welp, theres one channel Im never gonna be watching @@JacobTechShit

@DennisCrouse 5 жыл бұрын

@@JacobTechShit You mis-spelled "In addition to"

@PSBeard 5 жыл бұрын

I suggest hydraulic brakes, they are far more suited to that application then the mechanical ones you are using.

@darrenwoloshyn 5 жыл бұрын

PSBeard I have hydraulic disc brakes on my giant Talon 2 2018

@ultiss 5 жыл бұрын

i agree, massive braking power without much effort at the lever

@nathanielvogler7335 5 жыл бұрын

But can you get a double hydraulic lever?

@Gabriel-kz6kb 5 жыл бұрын

sure, its possible you just need a splitter in the line.

@jonah_chua 5 жыл бұрын

@@Gabriel-kz6kb but does the lever move enough oil to brake to 2 callipers?

@rahulmukundan1245 5 жыл бұрын

Congrats and You two stay happy togetherrrrrr.

@magic.marmot 5 жыл бұрын

I've been trying to catch all of the videos in this series. I really love what you're doing here, and I'm trying to take the lessons that you've learned to carry forward into my own projects. Thank you.

@mtnmyke 5 жыл бұрын

For the love of all that is holy, stop touching the rotor! The oil from your skin is enough to destroy the pads. Also, front and rear should be independent so she can properly modulate her braking. 👍👍👍

@anthonyt4981 5 жыл бұрын

like left handle brake is front and right handle brake is rear idk

@caydenfeemster5191 5 жыл бұрын

MTNMYKE I was thinking this the entire time

@TheUberKevlar 5 жыл бұрын

You must have some pretty oily hands, dude. My brakes work just fine after years and they've been through much worse.

@roopekaappola7177 5 жыл бұрын

Lmao, I once was working on my 2 stroke weed eater, I was adjusting the carb, with the engine over my bike which was laying on the ground, oil had built up and was basically leaking because I was running too much oil, so a drop of 2 stroke oil fell on my back brake, it still fine

@seanhawkins6184 4 жыл бұрын

Same all the real MTB people know

@miguelespinosaruiz9003 5 жыл бұрын

You should add wheel fenders you know so the dirt doesn't kick back up well off roading

@michaelellixson3633 5 жыл бұрын

Just can’t say anything else it is so fantastic beyond words I can tell you that thank you for being

@another3997 3 жыл бұрын

Great to see he did this upgrade. For anyone riding or making a bike/trike/quad, just remember that around 70 percent of the total braking ability is generated by the FRONT tyres. As Zack found out, back tyres lose grip due to inertia/weight transfer. Good for doing skids, bad for stopping.

@JohannesGustavssons 5 жыл бұрын

If you don't intend to have searing brakes like on a bulldozer or farm tractor I see no reason for connecting each side separately. If you still want two handles you have two serious and safe options: 1. One front and one rear, like on a normal bike. No risk of it pulling to either side in an emergency situation. And shouldn't be able to tip over. 2. Connect the brakes in a diagonal pattern. Front right and rear left. Even if just one brake is used it shouldn't to pull in either direction. Just like dual circuit brakes on any vehicle. However, if both handles are used with uneven pressure it may pull. The best and also simplest way would be to connect all four brakes to the same leaver. Simpler to use and always brakes on all wheels. It could be a good idea to adjust it so that the front brakes a little bit more than the rear, like on a car. 60-40 or something like that. No problem hooking up multiple brakes to one single leaver. Car manufactures has bin doing this for ages on parking brakes.

@jacobshepherd3997 5 жыл бұрын

Johannes Gustavsson I agree with you on every point but the last one. Those are mechanical disk brakes, they already take a decent amount of force compared to good hydraulic disk brakes to stop. My last bike had mechanical disk breaks, and on long descents my knuckles wouldn’t be white from hard gripping by the bottom. Then spread that force out to 4 different rotors plus the friction in the system from the lines running through the cable housing. And I doubt you would have hardly any stopping power

@JohannesGustavssons 5 жыл бұрын

Good point!! Didn't think about that at all. Maybe it would be possible to create a mechanical advantage. But in that case the brakes would need to be very precisely adjusted as the travel of the brakes radically decrees. Any play would be fatal for the function of the brakes.

@benjaminrafiee6966 5 жыл бұрын

U need suggestion? marry her already.

@osamazch 5 жыл бұрын

just what i was thinking

@z-flex5959 5 жыл бұрын

Meto

@ART-wz8mp 5 жыл бұрын

I think they are best match for each other..

@roni2671 5 жыл бұрын

@jamboy1686 5 жыл бұрын

Nah

@privatesector0422 5 жыл бұрын

I've never seen a more perfect couple. You two are definitely made for each other.😍

@garystarnes5178 5 жыл бұрын

Hey Cambry. You nailed that intro!

@dzengerink 5 жыл бұрын

Ok no worries you didn't give your viewers credit for suggesting to install the front brakes 😉😉 But second rookie mistake, instead of combining the rear and front on each side on each brake handle, try to combine both front brakes to one brake handle and combine the rears to one handle. You might otherwise tip over to one side when going downhill too fast.

@josharntt 5 жыл бұрын

The guy might've wanted to be anonymous

@ahmeddagher 5 жыл бұрын

يسطي عايزين نفرح بيك بقي ونقولك مبروك بقي 😀

@ahmeddagher 5 жыл бұрын

@@medouj I'm Egyptian 😀 but the comment related to his Middle Eastern fans 😂

@TtttTt-ub5xb 4 жыл бұрын

افرحنا فيه❤

@FantomsNephew 5 жыл бұрын

Makes me glad! Both the purpose and the build itself! 👍👍👍 As for requested hints: Consider Ackerman angles on the parallell steering rod tabs!

@dabigjokeoftheday 5 жыл бұрын

YOU ARE HER HERO..GO WITH IT.

@mslomnic 5 жыл бұрын

It looks like upper brake line is pulled heavier So there should be connected front brake which is more effective

@guy.h 5 жыл бұрын

Yes, all the 'put both fronts on the one lever' have not realised the levers exert different pulls on the cables. Therefore their solution would be MORE likely to induce a skid. With the front on the outside hole & rear on the inside and a bit of adjustment they should be able to find a nice balance.

@__ryan 5 жыл бұрын

3:02 That's what she said.

@josharntt 5 жыл бұрын

Might want to double check that

@__ryan 5 жыл бұрын

@@josharntt Might want to double check that

@Wiganpilot 4 жыл бұрын

I have seen all the videos about this tandem bike, it is just awesome. Cambry seems like a really cool person and a bit of a Dare Devil too :-D Brilliant invention.

@ChristopherKroukamp 4 жыл бұрын

Such a nice couple, perfect match for one another, love your videos too.

@cherunaranga3874 5 жыл бұрын

What happen if you put some sensors in the bike like dji drones

@MiketyDooDaa 5 жыл бұрын

What would that help with though?

@josharntt 5 жыл бұрын

Nothing would happen

@jremingo 5 жыл бұрын

Change the brake caliper to shimano or a avid.. it's alot stronger.

@charlieharper2529 5 жыл бұрын

this converted two bicycles project is one of best things i saw in my life :D

@jessicag6955 5 жыл бұрын

Love these! More videos with Cambry please.

@tahmidhossainadib5278 5 жыл бұрын

why don't you use the left leaver for the rear brakes and right leaver for the front brakes... :/

@ZacksJerryRig 5 жыл бұрын

Because these brake lines were already perfectly cut for the spots they are in. Streatching them accross the frame would get messy.

@tahmidhossainadib5278 5 жыл бұрын

well that makes sense... but i think she will face some problem while pressing only one brake...scene it's stopping only one side of the bike...but for the most part it will work just fine 👌👌👌

@batagnam 5 жыл бұрын

@@tahmidhossainadib5278 Yeah mee too, it's still a good solution for now but having the brake aligned is a better one. I'm surprise that no compagny offered you a solution before Zack, it would be great publicity for them. I guess there would be a solution to have only one handle bar with two brakes like a regular one :) It would need a mechanism but it isn't impossible :)

@tahmidhossainadib5278 5 жыл бұрын

@@batagnam there's no clean solution for this type of problems...but if someone wishes there's a lot of after market tools/parts to solv this problems... i mean if you want the most out of this you can use "hydraulic brakes if you want...than it will be one leaver for front and one rear...and you can use only one line for rear and at the brakes you can use a 'T' splitter... i mean at first this will be a messy as hell...but if you can stick to the plan you'll get a braking system which is verry powerful and aloso efficient :) ✌

@willian.direction6740 5 жыл бұрын

This could help turning in tight slow places like turning brakes on a tractor.

@thatdude5104 5 жыл бұрын

Warning: It definitely does matter what hole it goes into!

@timrudisill813 5 жыл бұрын

Absolutely phenomenal ! this is a marvelous, marvelous thing. appreciate you showing it to me and showing me further that it could be done. lovely young lady, and Marvelous young man. you must forgive the typos etcetera in this communication... I am using Google Voice typing. it still needs a bit of training. haha haha. I've had a few Strokes myself this summer but I'm coming along fine. use a wheelchair and I'm thinking about using one like you made. thanks ever so much.

@DoesNotGiveAF 4 жыл бұрын

This is awesome, Great job!

@Rs-02 5 жыл бұрын

JUST GET MARRIED

@truthhurts7742 5 жыл бұрын

Dude...I will marry her if you dont. She is hot, cute, and funny. You guys make an awesome couple. God bless you both. 😊

@JaxonRon 5 жыл бұрын

I think what you're doing is great. I love that you keep making improvements to it. I'd suggest redesigning the handlebars as well. Keep going. This could end up helping others as well.

@braznartn5176 5 жыл бұрын

Wow. Zack is a genius.

@_thegreasemonkey_ 5 жыл бұрын

She is so so much beautiful 😍😍😍❤️❤️❤️❤️❤️❤️❤️

@spice2110 5 жыл бұрын

U did it wrong. "show bob and vagana" np mate

@yousifa4002 5 жыл бұрын

Use this as a “marry her” button

@Blackxs93 4 жыл бұрын

Great idea with the new handles

@wingmanalive 5 жыл бұрын

If this guy doesn't have a crush on this woman I certainly do. It's amazing what you're doing for her!

@TheROZ 5 жыл бұрын

Im betting you marry this girl

@truthhurts7742 5 жыл бұрын

I hope he does. They look happy and awesome together. 😊

@athul_krishna_kr 5 жыл бұрын

A small update: they're engaged 😍

@kevinhosea85 5 жыл бұрын

"I don't think it matters what hole it goes in"... might want to check with your girlfriend on that lol

@CRIZZZLPT 5 жыл бұрын

not like she is going to feel a difference anyway

@Tater_Lord 5 жыл бұрын

@@CRIZZZLPT she can't use her legs it doesn't mean she has no feeling in them however

@kiyoponnn 5 жыл бұрын

@@CRIZZZLPT Rude lol

@sanjays9080 5 жыл бұрын

@@CRIZZZLPT ummm... Do you even understand how the human body works?

@Max-zp9xv 5 жыл бұрын

@@sanjays9080 hahaha lol 😊😉😀

@inshanhosein6292 5 жыл бұрын

Awesome tip for the brakes.

@johnphillip1711 5 жыл бұрын

Prob said elsewhere but compressed air makrs removing the grips a doddle (blow gun nozzle under edge and then just easily slide them off) Also I used to tap stuff on with my hands till I jarred the nerve in my palm, got a lecture off the doctor about it, told to use a rubber mallet instead. My wife has MS so I'm trying to forward plan and this gives me ideas and hope. So thanks :)