keeping the compressor tank cool is the key to eliminate condensation in the air circuit. very good job.

Nice setup you have. But I would turn your cooler 1/4 turn clockwise if you can change your inlet and outlet around . And set the cooler lower then the compressor discharge port. To help the water to move through the system to the water trap.(maybe turn the cooler counter clockwise if that puts your outlet lower than the inlet - it looks like the outlet is closer to the left side ? than the inlet is to the right side if so I would turn the cooler 1/4 ccw for better drainage)

I just ran across your video looking at other ways to dry air and I laughed when I saw yours. You and me had the same idea. I built my compressor set-up very similar to what you have about 15 years ago. It goes from a 2 stage 7 hp air compressor pump to a remotely mounted aluminum radiator with a 16" 12 volt race car fan. Then to a water trap with drain. Last to the tank. I use it mostly for my crossfire pro plasma cutter and it needs dry air. You have a great set-up and like you said it don't cost much to build if you know where to look. Be good Smitty 😎

Looks like a great system. I'm thinking of something very similar for my workshop.

I put a couple of automatic air dryers like they use on air breaks for big trucks in my airlines they pop off every once in a while but it works pretty good.

Great video! Thank you for sharing !

Bruh, good concept. The outlet temp on the compressor often reaches between 220-250 *F and them thar rubber hoses simply will not last, at least the output hose. Trying swapping it to an aluminum line which will prolong its lifecycle and maintain corrosion inhibiting properties. Just need a Flaring tool and some care in bending it to get it to your cooler unit (condensing coil). Just change that one line and your Golden........if you want to. Loved the concept.

I'd say this is the most cost-efficient setup I have seen so far, I was planning to go with the copper pipe design, not to mention about the current inflation, but I hate those pipes taking up so much space on my wall. Only wish I can install the tanks outside for safety precaution, but my experience had taught me that nothing can last under -30C up here in Canada. 😅

Really good idea I’ve never seen it before but something I definitely want to try

Thanks for that info.

nice setup. can't argue with science.

A/C condenser is the cheapest way. Mount in front of the compressor fan, no need to use an extra electric fan. Use old gas cylinders to expand your system capacity, also the cheapest tank rated 26BAR available from any scrapyard . Cheapest car air filter housing to muffle the inlet. Build your pipework from 3/4" for spraying purposes.

Great video. Planning to do it to my 60gal too. But unfortunately have limited space for an opening in the wall where to hang up the oil cooler. May i trouble you in asking approximately how tall & wide & thick is the oil cooler? Also - i saw this on other utube videos - you can put your wet dessicant onto a tray in the oven with small amount of heat & that will dry them out again instead of replacing. Thanks.

I would suggest you install a switch in the shop to control the outlet. Wire a light in series with the outlet and you won't be able to forget to turn it off. I like the cooler setup. I have one in the garage I may have to use.

If one of your air lines bust in the middle of the night compressor will burn up n catch fire 🔥 have it on a on off switch it happened to a freind

Thank you for a great video! Incredible how you make-do with basic things to make a great air system! I'm curious about one thing: do you have any problems with freezing temperatures...especially with you condenser and moisture trap being outside? It looks like fall/winter there in your neck of the woods. I'd worried about the condensate freezing and causing some problems.🤔 Thanks again for the inspiration!

What fan and what is your power supply amp rating?

Great video, perfect solution for moisture removal. I like this moisture removal solution more than others I have seen. Just one question. At the beginning of the video, looking at your lean-to, the cooler and fan are on the left, and the air pig (second tank) is on the right. As you get ready to leave the compressor and go in your shop, the cooler and fan are on the right side of the lean-to. Whats up with that? It can't be an optical illusion.

genuis!

Have you noticed a benefit with 2 big tanks? I work in a busy shop with a couple industrial IR piston compressors powered by 25HP motors and each unit only has an 80 gallon tank. I’m putting together a 5hp system with a max rating of 18cfm @175psi. I’d like to build a custom enclosure for the motor and pump, and then pipe air to a separate tank (or even use hose like in your setup). I’m stuck on what size tank I should go with. I’ll make room if i have to, but efficient use of space is my goal (and not annoying the neighbors or going deaf).

Not sure about the rubber hose connected to the cylinder head that gets up to 300 degrees. On the other side of the radiator it is probably ok. If you aren't around and that hose bursts then that compressor could run nonstop.

What was the eBay item titled as for my search? I’d love to repeat your process

How are the rubber hoses holding up? Lots of folks with similar setups use copper lines.

Bro how did you wire the 12v adaptor to the compressor I just ran across this video and I just bought everything to do pretty much the exact same setup that's about the only thing I have holding me back. I really like to hook up some kind of lighted switch so when I'm walking out my garage the light will catch my eye so I remember to turn it off

Can you explain exactly how you slaved your fan to go on and off with the compressor?

Harbor freight has a cooler for 700 dollars 99.9% free of water

Instead of plugging and unplugging your compressor remove your outlet and wire one in with a switch. This way it stays plugged in but the power is off.

Where did you get your hose?

I’m gonna use this same set up but will the 300 degree temperature melt that 3/8 rubber hose ??

What hose did you use from the head to the dryer? All the similar systems I looked at building used aluminum lines and all manor of weird fittings

great video.....I have a water radiator out of an audi. could I use that?

if your beads turned purple from blue then definitely there are water mist in there bro.

Never saw a rubber hose that could handle 300F. Worm clamps are dangerous. This is not a dryer this is a aftercooler. Perfect top it off with PVC. Anyone who listens to people like this get what they deserve. DANGEROUS!!! Do Not Listen to this person

ac condensers restrict air flo