...the air bag can be soften, by placing it in warm water, that's Not Too Hot... this will make it easier to install.

Outstanding video. Thank you 🙏🏽

Going to order some for my fiesta to haul my Honda grom around, hoping it’ll keep up for a few small trips without any issues

Add the air lines first feed line down though the hole at bottom of spring support, then you don't have to deal with forcing them on though a tiny hole.

Definitely put a 90 degree fitting on the line coming off the bag. That low hanging looped hose can catch on a million things on the road including basically any debris you drive over. Use an elbow fitting and make the hose hug the car as much as possible.

Best to attach black air line to red airbag nipple before you put it into spring. Spray a touch of oil into the black line. Use a hot Philips screwdriver tip to open up the black line, softening it. Push on the black line all the way and let it cool. bingo. Install airbag into widest part of spring, and route the black airline.

Just ordered the kit for my 02 focus wagon, hope i got the right part number. Curt hitch on the way too, maybe ill post a video on the install.

an easier way to get the air line on the fitting, heat some water in the microwave for a couple mins and dunk the tip of the air line in the hot water for a min or so. It will then slide on fairly easy and shrink back down tight as it cools off

THANKS

Nice cheers

got the 60724 for the focus wagon and I'm test fitting into a set of old rear springs on the bench, looks like bag diameter is definitely a loose fit diameter wise and length wise it's less than half of the relaxed length of the springs, does not look right to me even i double checked the pn on the manufacturer site it says correct. thoughts? Edit: they are basically "sausage thrown down a hallway fit" :)

This must be a different for your type of vehicle. Every video i have seen shows the bag being installed with the air house connecting to the top of the bag not the bottom. Including the manufactures video. Have you had any issues since the install?

I don't think silicone will hold for a very long time on a vehicle. It's why there are special sealers for the RV market. It doesn't hold up to vibration.

When ordering Air Lift 1000 Universal Air Spring Kit you need to take two simple measurements when your car is at normal ride height ... the inside diameter of Springs (y) and inside height of springs (x) ... Then use the chart below to find the correct kit KIT # MIN. DIAMETER (Y) MAX. LENGTH (X) 60900 .......... 3.00″ ....................... 5.50″ 60901 .......... 3.00″ ....................... 8.00″ 60902 .......... 3.00″ ....................... 9.00″ 60903 .......... 3.50″ ....................... 5.26″ 60904 .......... 3.50″ ....................... 7.75″ 60905 .......... 3.50″ ....................... 9.50″ 60906 .......... 4.00" ....................... 5.00″ 60907 .......... 4.00″ ....................... 6.00″ 60908 .......... 4.00″ ....................... 7.00″ 60909 .......... 4.00″ ....................... 8.00″ 60910 .......... 4.00″ ....................... 9.00″ 60911 .......... 4.00″ ....................... 10.00″ 60912 .......... 4.00″ ....................... 11.00″ 60913 .......... 4.00″ ....................... 12.00″ 60914 .......... 4.50″ ....................... 6.50″ 60915 .......... 4.50″ ....................... 7.50″ 60916 .......... 4.50″ ....................... 9.00″ 60917 .......... 4.50″ ....................... 10.00″ 60918 .......... 5.00″ ....................... 5.25″ 60919 .......... 5.00″ ....................... 7.00″ 60920 .......... 5.00″ ....................... 9.00″ 60921 .......... 5.00″ ....................... 11.00″ 60922 .......... 5.50″ ....................... 5.50″ 60923 .......... 5.50″ ....................... 7.50″ 60924 .......... 5.50″ ....................... 8.50″ 60925 .......... 5.50″ ....................... 9.50″ 60926 .......... 5.50″ ....................... 10.50″ 60927 .......... 5.50″ ....................... 11.50″

سلام این همه زحمت کشیدید و ویدئو ساختید. چرا اون رو امتحان نکردید؟

Is there a reason you left so much slack on the hoses? It looks like they could get caught up on something

for ford fusion v6, which one should i use?

What happen if my vehicle lower arm doesnt have that big hole under the bag valve pointing down?

Nice. Going to buy it for a 2010 Ford edge. Called a dealer and it's 102 for the pair, but 500 for install. Thats why I'm here.

I think you simply bought the wrong size bags. I've put the 1000's on an old Cadillac and an old Oldsmobile 98 and in neither case did the bags flop around inside the coils as is shown in your video. Clearly you need bigger bags for that vehicle? Actually, they don't look like 1000's . . . I think they gave you the wrong bags.

U habe the wrong bags