Air Suspension Problem? Try This CHEAP Fix! Land Rover Discovery 4 / LR4

Рет қаралды 17,865

Күн бұрын

Hello everyone! In this episode I want to show you how I fixed my problem with the front valve block of the air suspension.
The problem was that the front axle of the Land Rover Discovery 4 / LR4 often took a long time to be lifted. Since this always happened on the complete front axle I suspected a problem with the front valve block. And so I ordered an O-ring set to replace the O-rings of the valve block.
Again, I used the GAP IID tool to let the air out of the air springs, saving me from having to let the air out through the bolted connections.
The exchange of the O-rings took about 20 minutes with cleaning the valve block and is not a big deal.
All in all, a fairly inexpensive maintenance compared to a new valve block, even though it took some time (about 1.5 to 2 hours). The O-rings cost with shipping to the 25 euros.
If you find the video helpful, I would be very happy about a Like. If you want to know more about repairs or maintenance of a Land Rover Discover 4 / LR4, please subscribe to my channel.
All the best,
Peter
Where to buy the O-rings:
bit.ly/3vBNhti
INDEX:
00:00 Problem & Instructions
01:15 Deflating Air Suspension with GAP IID Tool
02:59 Dismantle the Front Valve Block
04:42 Valve Block disassemble and Change O-rings
06:50 Install the Valve Block
08:08 Re-enable EAS with GAP IID Tool
09:24 Does it work?
GAP-IID Tool:
Amazon: amzn.to/3LtlpO8
GAP Diagnostics: bit.ly/34S1uaw
IID Control - iOS App:
apple.co/3IybyV4
IID Control - Android App:
bit.ly/3qVUBOm
-----------------------------------------
👍 If you find the video helpful, I would be very happy about a Like. If you want to know more about repairs or maintenance of a Land Rover Discovery 4 / LR4, please subscribe to my channel.
📸 Follow me on Instagram:
/ notthatkindofachannel
✅ Support me via PayPal:
www.paypal.com/paypalme/mrmir...
-----------------------------------------
Thank you for your understanding that my English is not quite fluent. But I am trying to improve.
All the best,
Peter
⚠️ Please always pay attention to your own safety when working on a vehicle and never lie unsecured under a car! I do not accept any liability for the correctness of the information given in the videos or for damage caused by improper processing of products or by mistakes made during your own installation, nor for your personal safety! These videos are for entertainment purposes only and are not intended as instructions or for imitation!

Пікірлер: 32

@notthatkindofachannel Жыл бұрын

Do you have the same problem on the rear axle? Then checkout my other video ==> kzfaq.info/get/bejne/g82ihKdk1sWloas.html 👈

@ashy1423 5 ай бұрын

Thank you for this informative video 👍 Ash from Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿

@Doktorvollcrass Жыл бұрын

Discovery content ist immer gut!!! Danke dafür...

@notthatkindofachannel Жыл бұрын

Hi, ja stimmt 😄 Danke dir! Viele Grüße

@protohyp Жыл бұрын

easier to pop the center out of the panel clips as thats what locks it into place then remove the panel clip with the pry tool. that way you dont break them.

@ThomasFromHome Жыл бұрын

Hi Peter, thank you for the video. The linked repair-kit, is it only for the front valve block or does it contain the o-rings for the rear valve block too?

@notthatkindofachannel Жыл бұрын

Hello @Thomas! The linked kit is for the front, rear and pressure switches. So it is a very good price I think. :)

@barga.exploring Жыл бұрын

Nice

@piotreck 2 жыл бұрын

Could you link the orings? Great movie!

@notthatkindofachannel 2 жыл бұрын

@Piotr Kasnowski Thanks & Of course! I bought them here => bit.ly/3vBNhti

@Travelx82 Жыл бұрын

question if my on is more haning in the back do you have the same valve housing in the back ??

@notthatkindofachannel Жыл бұрын

Since they have the same o-rings and look the same, I would say with reservation that they are the same. However, Land Rover gives different part numbers for them. So personally, if I needed a new rear valve block - even though they look the same - I would order the one that is identical to the OEM. Best regards, Peter

@kargulo Жыл бұрын

Hi , I had the same issue on front , i desided buy new valve block , but after change evry morning I have to push up front about 2.5 cm, no idea what is wrong :) Thank for sharing info

@notthatkindofachannel Жыл бұрын

Hello kargulo! It sounds like there is a leak in the front part of the system. And if both sides are leaking at the front in the morning, then I think it could be a problem with the new valve block or its connections. Have you checked the lines and connections with some soapy water from a spray bottle yet? Greetings, Peter

@advantagemarine7305 8 ай бұрын

I have a similar problem, stripped my valve block down with the intention of swapping the O rings but one of the airline connections didn´t feel good on the thread so I ordered a new valve block but it is still dropping on the front, if I leave it in off road height it doesn´t drop so I don´t think I have a leak on the lines or air bags. I will investigate further and get back to you if I fix it

@naxaretalvarez4297 7 ай бұрын

Muchas gracias

@notthatkindofachannel 7 ай бұрын

You’re welcome ☺️

@abdelrahmanfarrag8928 9 ай бұрын

Thanks bro 🤍🤍

@notthatkindofachannel 9 ай бұрын

You're welcome! :)

@dayan_er.k 7 ай бұрын

Front and rear only 2 valves??? Or one???

@notthatkindofachannel 7 ай бұрын

Hello! No, actually there are 3 pieces in total. One valve block for the front axle, one for the rear axle and one at the compressor or air tank. Many greetings, Peter

@sibiryak2478 Жыл бұрын

Доброго дня! Думаю ты сможешь перевести мои слова на английский. Видео хорошее и полезное. Могу я тебя попросить сказать номер, артикул на эти резиновые кольца, что бы я мог их заказать. Спасибо

@notthatkindofachannel Жыл бұрын

Hi, I'am sorry but I don't have the original part numbers for the seals. But I order very good and cheap aftermarket seals from here: bit.ly/3Rx2qW8 Have a good day, Peter

@sibiryak2478 Жыл бұрын

@@notthatkindofachannel Да. Спасибо. но к сожалению вариантов доставки ко мне нет. Возможно это из за политических событий...

@notthatkindofachannel Жыл бұрын

@@sibiryak2478 That could be, of course. Try your luck on AliExperss or something. I think I've seen it there too. In the worst case, you can also renew the whole block. This is also available as a replica for quite a reasonable price.

@sibiryak2478 Жыл бұрын

@@notthatkindofachannel да, о замене блока целиком я уже думал. Но не всегда копии хорошие. Много деталей плохого качества. В данном случае замена только резинок в оригинально блоке, мне кажется более лучшим способом.

@notthatkindofachannel Жыл бұрын

Hey ,on AliExpress I have even found German replica parts of corresponding quality. Of course, it's a bit more expensive than ordering them from Germany directly, but at least it's an alternative to the delivery problems. All the best, Peter