that's right, buddy. it's true for certain cases, it's the case you're referring to. but filming here I can only simulate with a small tube

But pressure loss will be very high which will cause damage This joint is not right may be joint will be very strong but other part may damage due to high pressure loss in one side

thank you for comment

i'm agree with you

and leak

Considering the waste accumulation, it'd better set the source pipe insert into the drain pipe.

Exactly.

This is a temporary solution when you have not yet bought specialized accessories

@@Alex-Tips That’s fine. However, that specifically is never mentioned in the “silent” video. One might therefore assume some folk watching such will assume the technique shown is a workaround without potential problems.

@@johnluiten3686 yes. thank you. maybe I still have a lot of problems to improve in the way the content is communicated. I will change gradually.

@@Alex-Tipsyou can still alter the title after you upload.

I'm no plumber, but I'm willing to bet this has to be a code violation introducing toxic glue material to the inside of a pipe waterline if this is for drinking water or hot water that can melt it loose over time and cause massive failure. That's why I think a sleeve fitting on the outside is the correct and desired approach, not this makeshift Temporary solution for lack of not having the proper materials for the job from the get go. I wouldn't try this. I'd just wait till I get the proper fitting to join them. Sorry, but this is a fail and should be an instructional on what not to ever do. 🙅🤦‍♂️

Thank you for your opinion. You are a very technical person

I admire your ingenuity in developing this method, I wish you positivity. BUT as an electrician who regularly pulls cables through long runs of PVC conduits, these internal pieces would just get in the way and increase the likelihood of causing damage to the insulation and/or conductors. Not only that, but this would not satisfy Code.

Easy fitting use coupling.

Yes all rigt. . Frist step .

thanks my friend

it applies to emergencies

If the water pressure is not too great and the cut between the two pipes is tight and combined with the glue, it will not be lost

​@@Alex-TipsWhat type of glue is that? What's the brand name?

My thought, too!

yes. the 2nd one it applies to certain cases

. حوزظنظزننمممحخخ خوخ زن و زظظمحكجح ع هم

When you don't have enough tools, this is a temporary solution

Agree with Richard. The heating is a lot better on joint integrity. it is easy, but this video fake it like a hard job. I never fail doing it. This video method will easily leak on that opening internal sleeve, as it only has glue covering the gap. I think this video misguides people. Don't make excuse on temporary solution, you just didn't do it fair on heating the pipe.

do you think it's ok?

no!

yes, thank you very much, and you can apply it to the ventilation duct

yes, i will find a way to fix the problem

thanks my friend

Pressure does not drop, flow does. Pressure will actually increase with restriction. 👨‍🔧

When you work for a long time, the manipulations will become skillful

😂😂

thank. good luck

it's also not that significant

Yes dirt will accumulate

thanks my friend

thank you. is it good?

it's not entirely wrong. it only applies to certain cases

thanks bro

thanks my friend

आशा है यह आपके लिए उपयोगी होगा

yes

Можно применять для вентиляционных каналов.

yes. Great tips to help you connect

yes. let's accumulate for you

thanks my friend

That would be a great idea and the columns would look very nice without the joints being exposed

thanks bro

thanks my friend

yes, thank you very much

с грязными дренажными системами не подойдет

@@Alex-Tips not suitable for anything, I don’t know where you are from but the pipe you’re using is not for potable water being to thin. The whole video is crap!

Thank you for your Feedback

I agree with you, and usually I will connect the 2 pipes directly

thank you for comment

​@@Alex-Tips no thank you for destroying people's pipes so they can call a real plumber.

what you mean is to connect the 3 ends of the pipe to the letter T

@@Alex-Tips yes, exactly

thank you

that's right

thanks you

How surprised do you find it?

thanks my friend

It will leak water at the joint due to the cut not perfect esp done freehand.

thanks my friend

thanks my friend

Thank you for giving me feedback

thank you

yes. please test it and give me the result

yes. it works fine

thanks

thaks my friend

thanks

thank you

thanks bro

yes, you can apply it to ventilation ducts

Air compression with high pressure cannot be used

thanks. where are you?

thanks my friend

yes. thank you. Please save this connection