Alternator Repair Noisy Bearings Replacement

Рет қаралды 117,654

DIY Alam

4 жыл бұрын

Пікірлер: 35

@ToyManFlyer1100 Жыл бұрын

Hummmph...Nobody ever shows using the old bearing to push the new one back in....Inspiring!!!...👏👏👏🥂🥂👍👍👍💰💰💰

@coreyreum4107 Жыл бұрын

I wondered what went into doing this. After watching, it's not hard to do but I would definately keep buying new alternators due to the amount of time it takes. And, I don't have a press, good video!

@chrisfort7340 4 ай бұрын

Well done! Thank you very much for your time and know how to make this video!😎👍

@dustyfruitypie1633 7 ай бұрын

What make of bearing do you recommend? Excellent video by the way

@theakh4238 7 ай бұрын

Use heat on the aluminum housing, and support the backside of the bearing housing my dude. Its very easy to deform or even crack the alternator case pounding it the bearing out like that.

@ZutiDIY 7 ай бұрын

Thanks for the tip

@andykim681 4 ай бұрын

This is such a great video. Thank you very much for your effort to show how to replace it. I have a question about the replacement. Can you tell my what are the bearing size and any website address i can get the bearing?

@39FORTYWATER Жыл бұрын

Thank you for demo

@stevenbean9706 3 күн бұрын

ordered a bearing puller i couldn't get the inner bearing off by simply prying it buying every tool imaginable so i dont get stuck when i rebuild the next one

@dennisshaw1195 2 жыл бұрын

Great job

@frankensteinrules6511 Жыл бұрын

BEST VIDEO ON KZfaq!!!!!!!!!!

@sultan26706 Жыл бұрын

Perfect thanks

@videoworks7731 Жыл бұрын

thank you

@peblum 2 жыл бұрын

Why not replace the pulley while you're rebuilding. Thanks for the video, I'm learning!

@donald8354 Жыл бұрын

If the pulley is good why replace.

@Dassick89 10 ай бұрын

Because they cost the same as a whole alternator lol.

@Skandalos 7 ай бұрын

I wonder if I can do this without a press.

@desimundavlog773 Жыл бұрын

How to know a Pulley was good or bad ??can u explain it plz

@jesusp.7774 Жыл бұрын

The noise

@carleynorthcoast1915 Жыл бұрын

I'm not sure if this alternator would work because at 10:04 he is using the inner race to drive in the outer race which causes damage to the bearing

@AwsBadr Жыл бұрын

It will work. Would be better if he placed a metal piece to spread the pressure.

@benjaminzhou9503 8 ай бұрын

…. It seems to be a lady working on it, making the job even more admirable. Not sure though. The person was using the old bearing to drive in the new one. So didn’t need to worry about the old one getting ruined. I would put a thick piece of medal over it though, to push directly against the outer race on the new bearing’s outer race. Great video, very inspiring! Just need to make sure to use quality bearing, not all bearings are made equally well.

@carllinden533 Жыл бұрын

I hope my Trabant 601 alternator is easier. I don't have a press

@constantinchivu583 3 ай бұрын

Greu fără presă

@michaeldavid3672 10 ай бұрын

Where can I buy the bearings and what part numbers?

@ZutiDIY 10 ай бұрын

Ebay

@Imran-gu6gs Жыл бұрын

Good

@jerryfitz2002 6 күн бұрын

Good video but when you put a socket on to hit the bearing out without any support under it that bearing or housing will no longer be true. Gauge it and I bet it’s out of spec.

@Dr.JHIrons 2 жыл бұрын

I’d just purchase a new alternator..

@vr6swp 2 жыл бұрын

For my car, a rebuild kit with bearings, brushes and a new back cap is about $40 plus an afternoon’s work. New alternator is about $150-$200 plus core charge (and shipping both ways). You decide whats best for you

@stevenjosephs9 Жыл бұрын

Right , Remanufactured are crap ( shit )

@jesusp.7774 Жыл бұрын

And sometimes the aftermarkets are weaker on amps