AMS Performance Alpha Turbo Intercooler Install for Mercedes Benz GLA45 CLA A45 AMG M133

Рет қаралды 12,252

Күн бұрын

AMS Performance Alpha Turbo Intercooler Install for Mercedes Benz GLA45 CLA A45 AMG M133
🅷🅰🆁🅳🆆🅰🆁🅴
⚙️ AMS Alpha A45 Intercooler Kit.
www.amsperformance.com/cart/a...
0:00 Intro
0:55 Remove Stock Intercooler
8:00 Prepare new Intercooler
8:47 Install new Intercooler
10:46 Put it all back together
12:56 Air Lift Coolant (refill)
🅳🅴🆃🅰🅸🅻🆂
Installation of AMS Alpha Performance Intercooler Installation for M133 Engine in Mercedes Benz GLA45. Applicable for also A45 and CLA45 and GLA45s that come with two (2) Liter twin-scroll turbo AMG Engine.
🆃🅾🅾🅻🆂
🔧 Sockets and wrench sizes listed in video.
🔧 17mm, 10mm, 13mm, 7mm, T25, E10, M5 Allen (Hex), Flathead, Ear Clamp
🅼🆄🆂🅸🅲
⏩ Nine Inch Nails - The Slip - The Four of Us Are Dying
⏩ Silky Smooth - Audio Hertz
⏩ Monogram - Patrick Patrikios
⏩ Dorian - Andrew Langdon
⏩ Birds - Corbyn Kites
⏩ Into It - Kwon
🚫 Rude or offensive comments will be deleted 🚫
Culinary & Car Conquests - M.J.R. MJR Productions with Mike

Пікірлер: 41

@victoryroadperformance3131 4 ай бұрын

Perfect time to install our methanol coupler!

@manuelzamora9288 Ай бұрын

used a torque wrench to loosen the lugs??!!! nice....

@rssdefensecorp8756 3 жыл бұрын

Excellent Vidoe I have a 2021 GLA 45 do you have any Vidoe on the new ones

@goncalopinto3593 2 жыл бұрын

about the sound generator? do you need that? do you have problems without that?

@georgealferez8145 3 жыл бұрын

Did you drain all the coolant? How many liters of coolant did you put?

@YTGSpeedShed 3 жыл бұрын

Did you sell the intercooler and go with something else?

@renajforbesceoofmobay9814 10 ай бұрын

Can this Intercooler fit a GLA 250 turbo 4Matic x156 engine

@ntkenjiii 8 ай бұрын

excuse me,what is that sound generator for? thanks

@ericcyder 3 жыл бұрын

After removing the sound generator did you still get humming sounding in the interior cabin ?

@m.j.r.productions6276 3 жыл бұрын

No humming. However, I do plan to further investigate and completely remove all the 'stuff' associated. This does include determining what effect there might be for disconnecting the electrical or if there is a way to disable.

@cianomotorsport5275 Жыл бұрын

@@m.j.r.productions6276 Did you leave the resonator tube detached or did you plug it? Is the electrical part of the resonator still connected?

@cianomotorsport5275 Жыл бұрын

hi, i bought it too. can you give me some info if you can in private for the installation?

@laochek 3 жыл бұрын

I have same setup. Mb600. Ams hpfp. Amd main heat exchanger. Snow performance wmi stage 2.5. Now waiting for the ams intercooler and side heat exchanger. Cheers mate. Sub too

@m.j.r.productions6276 3 жыл бұрын

For Controller calibration, did you have the ECU done by a shop or are you doing the calibration yourself, such as with HPTuners?

@laochek 3 жыл бұрын

@@m.j.r.productions6276 the hpfp calibration was by ams but tuned in Singapore by Bms tuning. Managed only 596 hp 830nm at crank on mustang dyno. However its temperamental and occasionally goes into soft limp mode. Still trying to trouble shoot.

@ahmadfahim189 3 жыл бұрын

Since u already using mb600 turbo by ams, hows it daily usage? Its a journal bearing right? Does it laggy on the low rpm? Im thinking of upgrading mine.. but not going to upgrade the fuel pumps since im daily using it..

@laochek 3 жыл бұрын

@@ahmadfahim189 hi. Mb600 is dual ceramic ball bearing. Spooling is smooth but being a bigger turbo it still lag compared to stock. Boost only starts after 3.5k and explodes from 4 n peak at 4.5k. Nothing below 3.5k. So daily drive but in slow city traffic, and in C mode auto its a pain to overtake at low speeds and especially you are tired and want a smooth drive. The hpfp i believe is crucial for high end. I have seen some with 3071 peak torque at 4.5-5 but drops off quickly as fuel is a limiting factor. Imo mb600 with hpfp shd be tuned by ams. I might be sending mine over to Ams soon but downtime is min 1 week to factor in shipping to and fro.

@ahmadfahim189 3 жыл бұрын

@@laochek hi, tq for the response bro.. means it needs hpfp to support the top end.. what about the reliability for long term ? N if i took ams to tune it, do i need third party distributor to install the tune? Or i can do it by myself?