I’m watching your videos since i was 12 years old, and my dream was to fix lots of phones. Now I’m 18 years old, and i was fixing lots of phones, and now I’m working with Israel Aerospace Industries. Appreciate so much your time for making such good videos.
@keepthemindoccupied64775 жыл бұрын
Im learning so much from these videos this video was great the hints and tips alone from you are gold never stop posting videos .
@thelaxplaya77 жыл бұрын
We've done many of these and I personally replace the meson only and have not had any come back. Also if you are out of new mesons to reduce the chance of a bad ic, I've also been able to reball the same meson and have it work. Once I complete the repair we'll put something on the meson for pressure and then add the shield.
@ststele7 жыл бұрын
That's cool :) I hope you continue to have no returns. It can be maddening sometimes turning out 30 of these in a week. I didn't think about doing something to hold pressure on the IC after replacing it. That could be just enough to keep one from coming back that has a pad separated that goes unnoticed.
@billsalih47697 жыл бұрын
mate its great to watch you and see how devoted you are too both your business and family hope your day goes well too
@ststele7 жыл бұрын
Thanks man! You too :)
@spartan4567 жыл бұрын
Discovered your channel from someone over on r/mobilerepair. Great stuff. I think more channels like yours should exist. Thanks for doing this, and keep it up. 7:05. Hah. Gonna be completely honest with you. The first time I tried cleaning an iPhone 6 board of liquid damage, I informed the customer that I really don't know what I'm doing and that she should find a store that offers ultrasonic cleaning. She said it was alright, and to just try my best. I knew enough that I needed to remove the EMI shields, so I started going around the board taking them off so I could attempt to manually clean them. I flipped it over and started blasting that tape-covered area with heat. Sat there for minutes wondering when the fuck it would let me lift the shield off. Then I found out it was just tape and felt myself die a lot inside. Needless to say, that phone was very much dead after that, but it was also very much dead before. 18:40 I've found that most tacky fluxes seem to have that property of "locking" the chip down. It kind of flows right into place and does most of the work for you. I personally use Amtech 559, and it is actually reasonably easy to clean up even when cold. I use kimwipes and alcohol and an anti-static brush. A majority of it will get pulled right up. It also blows away very nicely on high air and low heat.
@ststele7 жыл бұрын
I did the exact same thing on my first iPhone 6 board. I toasted that sticker pretty good before realizing it was just a sticker! LOL I haven't used Amtech 559 yet but I'll probably give it a shot pretty soon when I make the next order. Thank you for the info and comments! I'm gonna be posting videos as often as time allows. :)
@RDSpike7 жыл бұрын
Hey, just came across your video a bit randomly as I considered doing some work on an iphone 6 logic board. I really enjoyed the video and the story of your repairs! Thanks for sharing and letting us step into your shop for a while.
@ststele7 жыл бұрын
You're welcome! I think these videos are helping me just as much or maybe even more than they are everyone else. I really enjoy it. Thanks for watching and commenting =)
@Mr.AndrewJones6 жыл бұрын
You should do a video on what tools you have, micro screw drivers, heat gun, etc. and where you bought them!
@abtoab63374 жыл бұрын
Yes I second you
@abtoab63374 жыл бұрын
Yes I second you
@og-01105 жыл бұрын
Hi, what is the reason you are also removing the broadcom chip?
@sharfazhameed63823 жыл бұрын
It’s my favorite channel n always ton of knowledge. Keep up the great work mate
@diyfixtool830 Жыл бұрын
साझा करने के लिए धन्यवाद, वीडियो साझा करना बहुत अच्छा है।
@andrebeese11457 жыл бұрын
Hey jason i have found out that sometimes only with heating up the ic sometimes the touch detection comes back for me it already worked 7 times and it does not take so long great video :)
@ststele7 жыл бұрын
Thanks! Yes these connections are so tiny even the slightest variation in temperature is enough to make them or break them. Hopefully it keeps hanging in there as long as you need it to. =)
@StellarTechRepair7 жыл бұрын
Don't feel badly someone will mess up due to you; we will mess up due to our own mistakes. You are helping us Jason! I wanna ask again in case you missed my question on the s3 data recovery video; have you considered chip-off technique for data recovery jobs? Also, I am going to start doing touch ic jobs real soon as I just got my new tools. I personally think you are changing too little. If i was sending you a board from one of my customers I would not only pay your low asking price but I would tip you! Haggling is not a good skill to try and hone on repair people, we generally sell ourselves short to begin with. I think you should be charging $200 for touch ic. How is it worth less than screen replacement? You are worth way more than your asking price Jason. I hope to see you raise the prices. I am going to charge $200 and I think Jessa charges $200. If they don't want to pay let them go to someone with less integrity.
@ststele7 жыл бұрын
Thank u! I think by chip off method you mean hooking directly to the flash memory and copying the data. I've thought of it but assumed it's most likely encrypted or have IDs on the file system that have to match for the OS to boot right.. It brought about more questions in my mind that answers and I moved on. LOL I'm sure there's a way to hook directly to the nand and copying the raw data but getting it to make sense would be amazing.
@ToknHaze7 жыл бұрын
This method only works up to Samsung S5. Hopefully they'll be stuff available for the newer Samsung devices with UFS's but all you need is a Jtag box (I recommend Z3X Jtag box w/ emmc adapter) All you need to do is solder 6 wires to the emmc or alternative points on the board if available (which means you don't need to remove the chipset) or you can buy a socket that makes reading not only way easier/more repeatable but it dumps faster! forum.gsmhosting.com/vbb/f672/emmc-adapter-easy-z3x-jtag-box-1691845/ forum.gsmhosting.com/vbb/f672/e-mate-pro-emmc-tool-all-1-socket-all-1-adapter-work-easyjtag-2097603/
@tastytechaddictsmtb7 жыл бұрын
I had this problem with the cameras after replacing both touch ic;s, I ended up replacing the voltage regulator tiiiiiny chip, which brought back the back camera and then ended up re soldering some of the front camera components like the ferrites, caps etc near the cpu shield, this brought back the screen camera then, the odd thing is all of the components were testing just fine, so im guessing the only thing that was holding them to to board was the glue, possible heat transfer through the board caused them to detach, which is bizarre as I heat sink everything to death and never have the problem when doing a main pmu ic.
@tastytechaddictsmtb7 жыл бұрын
iPad mini back plates make good soldering mats , you can put them in the ultrasonics when they filthy too.
@ststele7 жыл бұрын
Thanks! Weill give it a shot sometime. Have a few laying around :)
@S3piocomputersCanada7 жыл бұрын
Try silicone blue mat for oven
@user-nz5zp7xp9f7 жыл бұрын
Hi Jason. Thank you for the wonderful video! It is helping so much. Can you just tell me what liquid you are putting on on 8:37? Also I'd like to know what tools i need for fixing the main-board. For instance, heating gun, glue etc. Thank you so much!
@arsislami30832 жыл бұрын
I have same problem . Already jumper M1 . Replace U2402 and U2401 but same no touch . check voltage around ic , thats normally . Why like that sir .
@peternewman21927 жыл бұрын
@1:15 thank you from the bottom of my heart for not playing anyTechno Musak :) Isn't it a crime against humanity to call that music?
@ststele7 жыл бұрын
LOL! Thanks :)
@stratf01827 жыл бұрын
Hi Jason. Highly informative video thank you. If you don't mind I'd like to ask about how quickly you remove these chips. Am I correct in assuming you want to use higher heat to remove these chips asap before it starts affecting other components too much? looks like you using a bigger nozzle than I'm used to. What size is it? Be so grateful for your valued advice.
@thingsido30932 жыл бұрын
I want to give guarantee on my mobile repairing Shop but by seeing you i think it's hard to accomplish because your level is show much higher than me as compared to me I'm just a child
@bigshane56567 жыл бұрын
I fix quite a lot of phones with more so just headphones jacks/charging ports/ screens, etc, I an really looking to expand my skills and try to add this procedure to my skill list. Just have some questions about where you buy your replacement parts?
@mpmattmatt7 жыл бұрын
I need this done to my phone. Haven't found anyone in my area to do it yet though.
@wasaaal7 жыл бұрын
Hi Jack thanks for great Video just a question regarding the proper temperature for the heat gun
@baratsha7 жыл бұрын
Wassal Wasal 345-365 degree
@DODGEMAN2237 жыл бұрын
Hi Jason I watch your videos and I make sure I leave you thumbs up thanks for everything. I was wondering what is the model number of your power supply and how do you like it? Tks
@ststele7 жыл бұрын
Thank you! I'm using a really cheap one. It gets the job done but that's about it :) www.ebay.com/itm/5A-30V-DC-Power-Supply-Adjustable-Dual-Digital-Variable-Precision-Lab-Grade-/262294040786?hash=item3d11f170d2:g:RegAAOSw9eVXUIdZ
@salemx88897 жыл бұрын
thank you STS Telecom
@mbenjamin2926 жыл бұрын
When you fix a Samsung is it water resistant after you finish it?great video.
@deckydluffy7 жыл бұрын
Hello Jason, Very nice video.. I have repaired this touch ic too. But something went wrong, some of screen does not response for touch, especially at the letter R. Do i got something missed? Sorry for my bad english. Thank you :)
@wd5jlr7 жыл бұрын
Thank you very much. Very interesting.
@sharifmobiletech59057 жыл бұрын
Chuck Watson
@voodoopant6 жыл бұрын
I have an iphone 6 plus with a missing voltage PP5V1_GRAPE_VDDH . I changed meson and cumulus 3 times . Still missing . Did you have this problem till now ? Thanks !
@alexz817 жыл бұрын
Thank you ! Great video brother !
@wassimhussein11987 жыл бұрын
hello , can you please tell me what is the name of the metalic plate your removed at min 1:36 and what is its function in the phone (does it protect it or the user from any electro magnetic waves or interference ) I think its name is EMI shield as for Electro Magnetic Interfernce sheild , I got my phone screen repaired and the man said he removed and he will not put it back because it serves for nothing .... I would like to know if its their to protect me from the waves or protect the phone Thank you so much
@dafirmahmood7 жыл бұрын
good job its so clear i loved it
@pradipmagar88855 жыл бұрын
sir help me once i have changed touch ic on 6 plus customer complaing 12 times its freezing sometimes what should i do
@hafidtouhafi79927 жыл бұрын
HI Jason thank you for the vedio I replaced touch screen ic then the phone just turned on just light with no image what it could be ?
@ststele7 жыл бұрын
Sorry, to hear that! There are a lot of things that could be. I don't think there's any way for me to tell without seeing it.
@stalebread66276 жыл бұрын
how about not disconnecting battery and flexes with a metal tool....
@alaster337 жыл бұрын
Great video Jason , don't you just hate those videos when they don't speck but have that mind numbing music on 🙉,...Good news on that hand made shield proving ineffectual , but well done pioneering it so vigilantly for us all 🙏 , look forward to seeing more jumper work too soon ; P.s could you let me know the make and # of the flux used to sit those chips please ??? Kind regards Alaster
@ststele7 жыл бұрын
Thanks! Yeah, social media doesn't get you very far if you're not actually being social. LOL Well, for most people.. the howtobasic channel gets billions of hits and the guy never says a word. I've switched back to ChipQuik SMD291 for soldering these little guys on. It holds the chip snug for final heating when applied just right.. or it can be a total mess, either way. :)
@alaster337 жыл бұрын
cheers Jason , ill try get hold of some...
@aikajnabi17 жыл бұрын
What type of soldering tip you are using to cleanup the pads?
@kothargyi-lifetimetechnolo57565 жыл бұрын
Please post iPhone 6splus screen rotate not working error
@CHENAPPADY Жыл бұрын
Thanks God bless you
@rupeshkhedkar40884 жыл бұрын
Hi sir iPhone 6 touch not working
@antonmeden63347 жыл бұрын
I am really like watching your video, good like always! Greate repair.
@ststele7 жыл бұрын
thank you! :)
@sharifmobiletech59057 жыл бұрын
STS Telecom
@sharifmobiletech59057 жыл бұрын
STS Telecom
@pukesey12 жыл бұрын
🇰🇭Cambodia 20:30 How about TEMP ? and Air ?
@ultrapatch38437 жыл бұрын
Hi. What kind of solder tip do you use to repass the pads?
@waleedrishmawi44707 жыл бұрын
iPhone 5 when I try to power it on, apple logo comes on then off. And it keeps doing that and phone does not boot
@HermirioSantos6 жыл бұрын
What welding flux do you use in micro-BGA welding?
@mayurkakadiya78837 жыл бұрын
which tampretur do you use in gun for desoldring?
@royer23237 жыл бұрын
how much to replace the LCD and Digitizer connector on the board of an iPhone 6 and also a baseband reflow?
@ststele7 жыл бұрын
Sorry, I'm not able to offer a fix for the baseband issue at this time. Here's a link to our prices: www.ststele.com/special-services/
@malshami207 жыл бұрын
Hi Jason, just saw your video, great stuff. My iPhone 6 dropped and screen shattered. I bought a new screen off eBay.after connecting the new screen the phone reboots then screen goes red and turns off. Then happened over and over. I restored and updated phone with no help.however if I disconnect the last flex close to main processes the phone starts fine with no touch screen. Can u fix this knowing that I was planning to do it myself but I chickened out since my micro soldering experience is zero. Thanks.
@ststele7 жыл бұрын
There's a pretty good chance I could help. Have you tried to replace that front camera/flex? I'm guessing you already have, but if not, there's a chance it may be that.
@mohammedalhammami69297 жыл бұрын
which use you past
@Adil69547 жыл бұрын
Hey Jason.I am from Kazahstan video vere good thank you so much)))I have a question how many degrees put the soldering iron?then you a new set Touch IC Repair or from a donor?
@ststele7 жыл бұрын
Thanks :) The iron is set on 750F most of the time. It helps a bunch for the board to be warm too.
@ronaldsipiri82865 жыл бұрын
Hi Jason, How do I send my phone over to you to fix? Am in Hawaii right now...
@prprid7 жыл бұрын
I have a question about the adhesive shield you took of the bottom of the board at 7:00. I took that off of a 6s to clean for water damage, and that shield cannot be reused. What can I use to replace it or is it necessary? Thank you
@ststele7 жыл бұрын
I typically use kapton tape :) Probably not the correct thing but I think the idea of that conductive sticker is to keep interference out. Once it is in the housing, the back is covered by grounded aluminum housing. Seems to me the conductive sticker may only truly help during testing before they get installed into housings. I may be wrong but I've never had a problem putting regular ole' tape over it.
@geraldmcfadden22705 жыл бұрын
What do you think of kingbo flux?
@rudyespada93247 жыл бұрын
Great video Jason. What type hot air machine are you using?
@ststele7 жыл бұрын
Thanks. I am using this one and don't really run it all that hard. I'm set on 380C and 40% air flow most of the day. www.amazon.com/Aoyue-852A-Digital-Rework-Station/dp/B000HDDXY0/ref=sr_1_fkmr0_1?ie=UTF8&qid=1477954164&sr=8-1-fkmr0&keywords=int+852a%2B%2B+pro
@abtoab63374 жыл бұрын
Please I need help where can I get some tools to buy
@fixmobile40987 жыл бұрын
What are you using the name Filx
@highlysuspicious64177 жыл бұрын
How much is the metal shield?
@nickseulovski7 жыл бұрын
The only thing that is keeping me from doing this is that i do not have a heat gun. can i get away with not having a fancy one like you? Is it absolutely impossible to remove the chip w/o heat? to be honest I'm due for a new phone but really would like to fix the phone i have now.
@nickseulovski7 жыл бұрын
also is it absolutely necessary for ultrasonic cleaning
@ststele7 жыл бұрын
I paid $130 for this hot air station. There is no way to do it without a concentrated stream of hot air.
@ststele7 жыл бұрын
But just as important as the hot air is a microscope to be able to see it. It really is a tedious job man. I've never known anyone to do this type of thing successfully their first time even with the right tools tho.
@nickseulovski7 жыл бұрын
STS Telecom thanks for the quick reply man I appreciate it. Looks like I am going to be getting a new phone :| not looking to buy all the flux and the hot air gun nor the ultrasonic cleaner. how much do u charge to do this if u don't mind me asking. One more question, how do u test for bendage on the phone. As u said in one of ur videos, I have to apply a twisting pressure to be able to typed. Ps I have a 6 + :( fml lol
@anderson99dj7 жыл бұрын
can u fix my iPhone 6 plus
@uitmcklong467 жыл бұрын
what flux did u used?
@uttamdas78907 жыл бұрын
Thank you so much sir.
@ststele7 жыл бұрын
You're very welcome! =) Thanks for watching.
@larryromain7 жыл бұрын
what type of extractor fans do you use ? I work in a small corner with no ventilation so i never do soldering jobs in that small space.
@ststele7 жыл бұрын
There is a window right behind me that we pull air from. Right now we keep good airflow through the building and that's about it. I really don't make too much smoke working on these little boards but still always have fresh air moving through. I'm adding a new system for fume extraction pretty soon though.
@larryromain7 жыл бұрын
Thanks for the info man...I have been repairing mobile devices over 9 years now and i must say I am impressed with all your repairs, I live in the caribbean and visted the united states some years ago to do my certification in repairs, no motherboard micro soldering was done so most of what I have learnt on that level is from your videos, keep up the good work, Do you offer any classes ?
@khollyo7 жыл бұрын
how can i know if i need to replace both touch ic or just one, and wich one of them?
@ststele7 жыл бұрын
There's a pretty good chance you can get away with changing Meson only
@khollyo7 жыл бұрын
thanks ... love your channel .... what is the name of the other touch ic ?
@gotchou7 жыл бұрын
khollyo mansour u2401 is cumulus. You can buy 5 pairs of cumulus and meson(u2402) on aliexpress for about 35$
@MaanG2584 жыл бұрын
sir u seeing 2 toch ic
@pocketreviewgaming7 жыл бұрын
i have iphone 5c touchscreen sometimes doesn't work it been droped a lot will a new screen fix it?
@ststele7 жыл бұрын
It's most likely the screen if you haven't tried a new screen yet. I do see a lot of those with touch IC failure but it is usually just the screen.
@pocketreviewgaming7 жыл бұрын
Ok thanks
@user-ux3hp9qj7m7 жыл бұрын
Thank u man.
@ilianavillegas97057 жыл бұрын
Is there anyway you can fix mine I live in North Carolina , how much would it cost and what do I have to do . Ship my phone to you ?
@ststele7 жыл бұрын
I believe you called the shop. Hopefully you have figured something out by now :) Apple has a deal going now for $150 to fix it if you have an Apple store near by.
@london49837 жыл бұрын
Are you reballing them or set a new one? Sorry for my bad English
@ststele7 жыл бұрын
I think in this video I used new ones. In the past I always used new ones. Now I reball Meson and re-use it 99% of the time because it is a good IC. The PCB is at fault.
@london49837 жыл бұрын
Thanks a lot
@mariltonmoreirafranco46477 жыл бұрын
Good afternoon Jason! My name is Marilton, I'm brazilian. I would like to know, what temperature and air pressure do you use to remove the CIs. Thank you for yours videos.
@ststele7 жыл бұрын
390C most of the time but how far the nozzle is from the board makes a huge difference.
@mariltonmoreirafranco46477 жыл бұрын
thanks dear friend for yours help!
@spenner117 жыл бұрын
STS Telecom Hi there Jason, i've been practicing this repair on damaged boards and have had some success but im having trouble with both chips "slipping" when working them back onto the board. i'm thinking too much airflow? Wondering if its possible we could have a more in depth chat? Thanks for all the great vids, repair shop out of B.C Canada.
@mrsemifixit7 жыл бұрын
What do you think about some shops only charging $40-60 for these board level repairs? Doesn't make sense to me for the amount of work involved
@ststele7 жыл бұрын
That would work out ok if there was never any problems... ever. I think those are the shops that the moment they see a torn pad or something, they cram the IC back on the board and send it back as no fix. Or they throw a chip on it and if it gets touch, they get paid, if it doesn't - no fix. I really don't think they're doing much troubleshooting for that price but then again, if they live in a place where $20 per day can pay the bills, maybe they do a dang good job? LOL - No way I'd do it for that price unless I could go back to living with my parents! :D
@mrsemifixit7 жыл бұрын
STS Telecom Lol I agree. Sucks though because to an average customer the lower price seems appealing and could take away from other shops. How do you get most of your customers? Having trouble finding customers locally and want to generate some mail-in repairs
@ststele7 жыл бұрын
I used to pay Facebook to boost posts mostly but since I started posting videos here, I haven't paid Facebook another penny. It's gotten to the point that local walk-in traffic is very difficult to manage. It has slowed down some though. I'm finally starting to catch up now that Apple is offering a "solution" to the touch IC issue. That made a huge difference in mail-in volume overnight.
@mrsemifixit7 жыл бұрын
STS Telecom Nice. How did you start getting mail-in repairs?
@fixmobile40987 жыл бұрын
Thank
@a.s.j.44657 жыл бұрын
Hey good job !!! Which hot air gun do you have ?
@ststele7 жыл бұрын
Thanks :) I'm using this one: www.amazon.com/Aoyue-852A-Digital-Rework-Station/dp/B000HDDXY0/ref=sr_1_1?ie=UTF8&qid=1483029705&sr=8-1&keywords=aoyue+hot+air
@a.s.j.44657 жыл бұрын
STS Telecom thanks !!!
@chriskat19717 жыл бұрын
Good morning Jason, first off just to say great job with your videos and your approach, i have a question that maybe you might have an answer to, ive run into a problem recently on a few 5s and 6 not sure if other models are affected but the phone comes into me with either the connect to itunes logo or in a boot loop and then during an update or restore i get an error 9 and nothing i do gets it passed that, changed batteries, charge ports, screens, U2 ic in some cases but still the same. The few cases i've come across the owners haven't done anything unusual with the phones, they just go into the connect to itunes mode on their own.. Any help or ideas would be greatly appreciated..
@ststele7 жыл бұрын
Sorry, I should be able to answer you better here but this one is really not one of my strong points. It sounds like you've covered all of the basics including Tristar. I did a bit of Googling on error 9 and didn't come up with much other than possible network issues or software security problems. Hmmmmm.. Since you said a few, that really makes me think that this is software update related? Hopefully you've figured something out by now - I'm 2 days late. Thanks for the good compliments =)
@chriskat19717 жыл бұрын
Thanks for the reply, it looks like i'm just going to have to wait it out for a software solution.. i was hoping it was something i was missing.
@chriskat19717 жыл бұрын
An update on this, i read on a forum that it maybe a cpu issue and someone had some success by applying pressure to the cpu during the restore process so i gave that a try on a 6 by opening the phone and using 2 clothes pegs to clamp down on it during a restore and it worked, I have no doubt that it is only a temporary fix but at least i know what the problem is now..
@khangahraman58917 жыл бұрын
i had the same problem, i changed tristar and bla bla it does not work after that i made a big risk and i reballed NAND disk it is working now
@nassimr457 жыл бұрын
hi Jason I have a question where did you learn to do this all of this
@raulmorel18727 жыл бұрын
Nassim Razick i think like every technchian diy underground
@ststele7 жыл бұрын
Just a natural interested and hands on. I learned most of what I know about electronics before there was smart phones building radios and stuff with my dad. In the past couple of years I learned that it was all still the same stuff, it just requires a microscope to work on it now. :)
@baratsha7 жыл бұрын
Hi y don't yu use uv paste to under fill the ic???
@baratsha7 жыл бұрын
98%success rate
@ststele7 жыл бұрын
That's a really nice success rate :) I may give it a shot one day. Thanks!
@GeeKwide7 жыл бұрын
i remove both of touch ic but phone don't swich on :( what i have done wrong !
@ststele7 жыл бұрын
There are a lot of things that can cause this. It's usually something fixable but not always so easy to find.
@GeeKwide7 жыл бұрын
i think it's the power manager ic :( cz with microscop it's look like it's get shorted !
@gotchou7 жыл бұрын
GeeK check for short to ground on your capacitors on the power line
@GeeKwide7 жыл бұрын
hi :) im just nebie where could i find it ! dd u mean capasitor near power ic managment !
@ToknHaze7 жыл бұрын
ok but have you ever actually tried to underfill a chip after confirming that the touch is working?
@ststele7 жыл бұрын
No, but I have had many of them have flickering grey bars resurface merely hours after giving them the all clear. I test them very well too. It's strange how this can resurface with zero bending, then another swap of Meson fixes it sometimes for good, sometimes for a few weeks. I really don't think underfill is going to prevent this. It would certainly make warranty work a nightmare and there will be warranty work.
@ToknHaze7 жыл бұрын
STS Telecom fair enough. Have you tracked the rework rate of full devices vs board only? If the housing is still bent or even partially bent it's going to be more prone to further flexing and subsequent failure. I'd suggest a pad over the mason and an insulated future proof plate with the thickness of an ipad mini lcd back bracket.
@bomark20026 жыл бұрын
Why would this vid get a thumbs down?
@badbadleroybrown6507 жыл бұрын
How much do you charge to fix this and how long does it take?
@ststele7 жыл бұрын
+Adrian Levy Currently our turnaround time is 3 to 7 days and we charge $125 + return shipping.
@badbadleroybrown6507 жыл бұрын
Can you send me info?
@ststele7 жыл бұрын
micro.repair/mail-in
@badbadleroybrown6507 жыл бұрын
Is this consider a routine repair or a non routine repair? And thanks for the shipping info.
@badbadleroybrown6507 жыл бұрын
Also do you replace the IC's for that price?
@el_drak37 жыл бұрын
How is that hot air? I want a budget H. A.S.
@ststele7 жыл бұрын
If this hot air station quit today, I would buy another one. I use it all day every day and it is very consistent. I couldn't imagine spending $1800 or even $800 on hot air. Maybe one day.
@el_drak37 жыл бұрын
STS Telecom Thanks for the input, and thank you for always being available to respond immediately. You are #1.
@ststele7 жыл бұрын
One more thing about this station. If you buy one, remember to remove the shipping screw from the bottom. I think everyone that you hear say, "they vibrate and are SO loud" - didn't read the directions. :-)
@el_drak37 жыл бұрын
STS Telecom very good 😂😂, thanks again.
@lynnnash45767 жыл бұрын
Jason can you say what model is your heatgun
@ststele7 жыл бұрын
This is the one I'm using. Despite what I've heard about low end stations, this sucker has been a workhorse. It runs almost all day every day. www.amazon.com/Aoyue-852A-Digital-Rework-Station/dp/B000HDDXY0/ref=sr_1_8?ie=UTF8&qid=1478050839&sr=8-8&keywords=aoyue+station
@lynnnash45767 жыл бұрын
Thank you Jason it seem to work well in your videos
@agaragar214 жыл бұрын
iPhone Husbandry !
@benjaminhong6877 жыл бұрын
Lol did you notice the electrical tape stuck right above the touch ic chip? there's some video claiming to fix problems by applying pressure to the chip