I took my washer apart to change the bearings and noticed a broken shock in the back. I then noticed my stator and rotor were full of what looked like dried grease, and I was thinking I might want to replace those as well, but after seeing your video here I think I'll save that $200 since yours look as "dirty" as mine. Thanks for showing the replacement on older machine!
@arettaschils94057 жыл бұрын
Thank you so much for the easy to follow video. We are in our mid 70's and had not problem until we put everything back together. When we went to put the stator cover back on, the shaft did not come forward and it took us forever to figure out what had happened. It finally dawned on us that the drum might have shifted. My husband went to the front and push on the drum and sure enough, the shaft came back. It took us longer to figure that part out than to do the whole job. Thanks again for saving us a service call.
@appliancepartspros7 жыл бұрын
Awesome, glad the video helped you get the washer up and running!
@kamparml89442 жыл бұрын
U
@brandenmarkevich Жыл бұрын
If the drum has lots of play in it to the point where it moves back and forth a few Inches front and back, that could be an indication that your drum bearings are bad as well. That’s a major undertaking
@arettaschils9405 Жыл бұрын
We fixed the washer and it gave us another 3 years or so of service. But eventually, it gave up the ghost and we replaced it. It was well worth the time to fix it to get more time.
@vincentheslin96363 жыл бұрын
Matt is the king of appliancepartpros. Give him a huge raise, his videos rock.
@graham53295 жыл бұрын
Good video on fixing this problem with my LG washer; failure of this hall effect rotor position switch is common on these washing machines and is evidenced by the drum twitching instead of rotating; when I fitted a new one following these instructions it now works perfectly again.
@appliancepartspros5 жыл бұрын
We're glad we could help you with your repair!
@forrestjoyner75934 жыл бұрын
Great video. I was lucky that the main bolt came off without having to brace the drum. I used a 3/4" 17mm socket and gave a couple good torgue jerks and it began to move. I'm winging this whole replacement based on videos and comments that the position sensor is actually the problem, but for a $12 part, it's worth it for me to roll the dice. The only glitch so far is that of the three tabs on the outside of the stator that hold the sensor in place, two of them sheared off when I rotated up to remove the old one. Nothing to be done about that now. The one remaining tab (on the outside plus the one on the inside diameter) seems secure and I didn't use any kind of unusual force to remove the sensor. I would have to assume that the plastic was just brittle. Point being here, to be VERY CAUTIOUS when you remove the old sensor. I might use a spot of superglue where the two tabs now have nothing to hold them. Can't hurt, but I don't know if this plastic will work with super glue. So now I wait for the new sensor to arrive tomorrow to put it all back together.
@forrestjoyner75934 жыл бұрын
To continue....part came, I had to notch out the hole for the backside retention clip like someone else said....the hole is not perfectly sized and positioned/aligned. Razor blade and dental pick did it. A small file would have done it, too. I used a Sharpie to mark the part that juts out from the stator since white on white makes it very difficult to see the alignment. I put it all back together and it's working. We'll see how long it lasts. So far, so good.
@alanderego3 жыл бұрын
Exactly what I needed to fix my washer! The only problem I had was the rear cover screws stripping while I was removing them. I had an extraction kit and got that taken care of and the rest was easy!
@lisadelorme66152 жыл бұрын
Thank you for the video. I have replaced one other part on my LG washer and both relatively easy with videos like this.
@jerrym23219 жыл бұрын
Easy as pie! Washer back to normal. Thanks Appliance Parts Pros!
@appliancepartspros9 жыл бұрын
+Jerry M Awesome, glad the video helped you get the washer fixed!
@Oohdang59 жыл бұрын
I've been struggling with this LE problem for months, trying various techniques to get it temporarily running again. I've tried resetting it by holding in the start/pause button for 5 seconds, I've tried unplugging it and leaving it sit over night, I've tried manually rotating the hopper clockwise and counter clockwise, which all are things that have worked before but the error kept coming back after awhile. This time none of those tricks worked, so I used this video to replace the rotor position sensor. Your video was very informative and very easy to follow. Got the sensor replaced without any trouble. However, I am still getting nowhere with this machine. I can get it to fill on a rinse + spin cycle, but when it finishes filling it sits there and does nothing for a couple of minutes then LE error. Sometimes it will attempt to spin and make a grinding noise before flashing the LE error. I can get it to drain by using a quick cycle, but then the same thing happens where it just sits there before giving me an LE error. Its not a too much detergent issue as this is happening with water only. I'm running out of ideas, do you happen to have any?
@appliancepartspros8 жыл бұрын
+Matt Hukill If you hear a grinding noise it could indicate a problem with the bearings. Bad bearing might over heat the motor or cause the inner tub to bind up. You can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem.
@TheRainmaker446 жыл бұрын
replaced actual rotor,,teeth on rotor were stripped...pull off rotor and inspect!
@depecheone2 жыл бұрын
Thanks Matt. Video is very clear and easy to follow. My Kenmore is humming once again. 👍
@erikayork85733 ай бұрын
This fixed my LE code! Thanks for the great instructions, down to socket sizes!
@appliancepartspros3 ай бұрын
You're welcome!
@souldoubtvicarious9462 жыл бұрын
I'm a fairly capable handy man around the house, but appliance repair i'm not, so i'm extremely thankful for this video. Great Job!
@drakes46253 жыл бұрын
If you can't remove the 17mm bolt, use impact wrench or have someone hold the drum. If you have trouble removing the round metal cover, tie some rope to its holes and pull off (it's magnetically held in).
@futfut16 ай бұрын
I used a breaker bar and it came off with a quick spin
@hectormedina80164 жыл бұрын
Replaced drain pump and door lock but that didn’t fix my washer. This sensors did.Thanks!!!!
@darwinescobar76295 ай бұрын
Its probably and old coment but was the probblem you experienced with your washer?
@jkling17175 жыл бұрын
EXCELLENT Video. Very well done. Straight-forward without excess
@appliancepartspros5 жыл бұрын
I'm glad we could help.
@philipsullivan93014 жыл бұрын
that was the bearing cover hanging there the whole bearing is shot along with the seal. you replace the whole tub in the back along with the basket it has the spider attached to the tub.
@jtl87 жыл бұрын
Thanks for the advice. I did the repair on the weekend and it worked.
@appliancepartspros7 жыл бұрын
Glad the video helped you get the washer fixed!
@scotthubbard38239 жыл бұрын
I replaced this part following the directions above. Great step-by-step instructions, so I thank you for that. Unfortunately, replacing the rotor position sensor switch did not resolve the LE code on my machine - in fact, the problem seems to have worsened. Any other recommendations on what could be causing this error code? Thanks in advance.
@appliancepartspros9 жыл бұрын
Scott Hubbard You can try to reset the washer, if there is a problem with the control board and motor not communicating. To reset it unplug the washer and press and hold the start/pause button for 5 seconds. Then plug it back in run a rinse and spin cycle to test it. If there are any soap suds in the tub it could cause the code to pop, make sure you get rid of any excess soap and you should probably use less soap. If that does not clear it then you may have to check the wires in the motor wiring harness and the main control board. If you need more help you can always post the problem along with the appliance model number on our repair forum and the techs will help you out.
@russelldean9857 ай бұрын
Great video. Easy to follow with clear instructions!
@appliancepartspros7 ай бұрын
Thank you! Glad we were able to help you out. If there is anything we can hep you with in the future please let us know.
@adamanderson98814 жыл бұрын
I can't get that bolt off, I think God himself torqued that bad boy
@aqueen75910 ай бұрын
I used visp grip pliers
@futfut16 ай бұрын
Breaker bar made it easy for me.
@kevinhurst87619 ай бұрын
Easy fix. Harder to find the part number than to replace.
@appliancepartspros9 ай бұрын
If there is something we can help you with please let us know.
@mike_oe Жыл бұрын
That was quick and dirty, albeit instructive. If that had been your own machine, I bet you'd have cleaned the stator and rotor before assembling it. I assume ocf, that the bearing and seal will be taken care of outside the video.
@Xclusive6158 ай бұрын
How do you clean the stator and rotor? Mines looked like the one in the video but can’t find any info on cleaning. TY
@shelnino Жыл бұрын
Thank you so much for the video!!! You just saved this amateur a ton of time and money. My washer is fixed!!
@whistledink8 жыл бұрын
Great video, informative and helpful. Walked me through the process, washer is all better!
@appliancepartspros8 жыл бұрын
+Bill Vincent Glad the video helped you get the washer up and running!
@Shaker4x47 жыл бұрын
It's great that you can buy parts online etc, but I'm in Australia, and manufacturers don't sell parts to the public, only to qualified, or authorized repairmen. Easy demo here, but you put it back together with a bad bearing unresolved :-P
@appliancepartspros7 жыл бұрын
We made a separate video for that: kzfaq.info/get/bejne/j5OVdNmgp6-ZaY0.html&lc=z13sfljphkvoytild23gdtmbity2w3x4a04
@villez38 жыл бұрын
Great video! It was clear and well done! I have a question. I replaced the sensor switch on my LG washer but I am still getting the same code (LE). Any idea what else it could be? The part I received was 6501KW2002J instead of 6501KW2002A, will this work?
@appliancepartspros8 жыл бұрын
+villez3 There are a few other things to check out if this did not fix it. More than I can type out here, you can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/ LG has been known to change the last letter on parts, if you have any concerns about it working you can give us a call with the model and serial number of the washer.
@steveyoung51152 жыл бұрын
EASY fix thanks to your video. MANY THANKS
@markkuroski25717 жыл бұрын
Thanks for the video! I'm going through the ball bearing replacement and was wondering while I have the circular copper piece (motor/rotor?) off the machine should I try and clean it? It's got what looks like grease and rust on it from the bad bearing gasket leaking on it throughout the years. Or does it need to have grease/lubrication on it in order to function correctly? Some of the wrapped copper wire has so much gunk that the copper wire looks like black wire. Should the whole thing be shiny and new looking on both sides? Thanks!
@stevenwilliams1497 Жыл бұрын
Thank you so much saved me so much money!
@alexappliancesrepair97439 жыл бұрын
Is there a video following this steps about changing the bearing follow apart like you mention on 1:57 seals going bad etc. also what's the part number so I can order the blue treat sealer . Thank you very informative video helps alot
@robertmattison12824 жыл бұрын
Why didn't you clean up the rust? Was the water getting to that location because the gaskets seals broke down? I give you video a B- from not cleaning removing the rust. I also give an A+ for taking the time to produce this video and uploading onto KZfaq. Be safe my friend.
@revsmitty9 жыл бұрын
Excellent! Washer is running again after watching this.
@appliancepartspros9 жыл бұрын
revsmitty Glad the video helped you get the washer up and running!
@revsmitty8 жыл бұрын
Doing this again. What are we doing to cause this piece to keep breaking?
@philipsullivan93014 жыл бұрын
new rotors do not come with the sensor and you cant order it. the stator connection has changed and the conrtol board no longer uses the sensor plug.
@perogi217 жыл бұрын
Thank you thank you thank you thank you!!!! Also a huge thanks for the close-up shot at 5:39. I started to wonder if I needed to tighten the bolt more because there was a bit of a gap but this showed me that it was all set. I do hear a bit of a clicking noise (once per revolution) - is that normal? I don't remember hearing it before but I also don't recall listening to the washer run
@appliancepartspros7 жыл бұрын
You're welcome! And thank you for your kind feedback. If you need any more help, feel free to contact us. We’re available 7 days a week at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/
@itsjordan176916 күн бұрын
Thank you
@appliancepartspros16 күн бұрын
You're welcome!
@philipsullivan93014 жыл бұрын
replace rear tub assembly and basket and tub seal to replace bearing.
@newmagoo Жыл бұрын
Thanks for this, very helpful video!
@appliancepartspros Жыл бұрын
You are very welcome!
@mayolomorales85124 жыл бұрын
A mi parecer el problema principal fue el retén pasando a dañar los baleros. Y en este vídeo no se corrigió el problema principal. No entendí si en otro vídeo se realizaría pero eso no es ético para el cliente
@ssdtrain18 жыл бұрын
@ 3:37 "To put the newww rotor poswitionsenzerswitch on" HAHA :)
@oliverharrison99175 жыл бұрын
The bolt on mine just will not come off, it just won't move, no matter how much pressure I apply. Any advice on removing it or why it might be so stuck?
@TippyPuddles5 жыл бұрын
Wedged the drum in front with a broom handle and chair. Then used a hammer with quick smacks to the wrench. The bolt was extremely hard to turn for three quarters of the way out. Then it moved freely.
@pollydor07 Жыл бұрын
Thank you much
@greggrzegorowicz88482 жыл бұрын
i have a older LG front load washer, IT STARTED A WASH AND QUIT, IT ,I CHECKED THE PUMP IT FINE, WSHER HAS A LOUD HUMM, I CAN SPIN DRUM BY HAND, DON'T SEEM TO BE LOCKED UP, JUST SETS THERE AND HUMM;S
@SomaElectricals9 жыл бұрын
What about bearing u have not Changed that
@appliancepartspros9 жыл бұрын
Bijay Singh Negi We did do a video on the washer tub bearing: kzfaq.info/get/bejne/j5OVdNmgp6-ZaY0.html
@theodorehyatt17823 жыл бұрын
I don't understand why you didn't clean up the rotor of all the rust they are pieces of metal that shouldn't be near the stator I know you are just showing how to do RPS but not very professional looking great video
@Xclusive6158 ай бұрын
How do you clean the stator and rotor if they look like the ones in the video?
@JohnAdamTurnbull8 жыл бұрын
Great video -- really well produced and clear. Thanks! But my LE problem persists -- not as badly as it did before I replaced the sensor. I guess I have a bearing problem, so I've watched your bearing replacement video too. I really don't want to tear the machine down so I'm wondering whether I can be sure I have a bearing problem and not something else. I get a very brief growling noise during load measurement, a whirring noise on spin-down, and the LE error code with what seems like a moderate load (three bars). There was no evidence of leaking when I took the rotor off to replace the sensor. Should I tear it down or reconsider some other problem? Thanks!
@appliancepartspros8 жыл бұрын
There is no way we can say what it is but grinding and whirring are usually bearing sounds. I am assuming you went through all the reset procedures. If you need more help trouble shooting I would suggest posting the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
@TippyPuddles5 жыл бұрын
I can't budge the motor rotor. Any suggestions?
@williamkterrell7 жыл бұрын
You guys are great keep up the great work
@appliancepartspros7 жыл бұрын
Thanks! We'll do our best. :)
@DrewDiaz6 жыл бұрын
Yeah well, I have a wm0642hw and it turned out the problem was the braided anti leak stainless steel hoses, these evident have some kind of valve in them and the water pressure in my house stopped the hose up.. same 1E, lE error.. figured this out after having swapped out the sensor. Put a set of rubber hoses on and I was good to go.
@appliancepartspros6 жыл бұрын
Thanks for that tip!
@terrysmith8119 Жыл бұрын
IT WOULD BE NICE TO KNOW HOW TO TEST THE MOTOR AND THE SENSOR TO DETERMINE IF THEY ARE BAD.
@robertagarcia8576 жыл бұрын
Thank you good jobs
@therealrollaz5 ай бұрын
Do you know what the ohm readings should be on the hall sensor and on which pins to verify it's the problem?
@appliancepartspros5 ай бұрын
What is the model number of your washer?
@kd-bc1lz4 жыл бұрын
That washer thingy hanging there after you removed the rotor. Did you re-use that? Mine is also in kind of rough shape and I'm note sure where to get that part.
@ericpham82053 жыл бұрын
if we use the bearing as position sensor is more accurate and less hackable
@davidfitch51964 жыл бұрын
replaced the sensor. Ran a load of just water no issue. Put clothes in and the error came back. We checked the wiring and it looked good, What else could be wrong?
@wjnapier49587 жыл бұрын
Replacing hose plumb to new plumb filling for Bosch washing machine
@appliancepartspros7 жыл бұрын
If you're looking for parts or technical advice, you can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We also have a free repair forum where the techs can help you troubleshoot the problem: forum.appliancepartspros.com/. We’re here to help 7 days a week.
@jillraleigh30363 жыл бұрын
Question. We followed the instructions...and to our surprise the rps sensor is missing from the washer. Ours doesnt have it. What do we do now??
@gauhdrung3 жыл бұрын
My father in-law LG Front loader washer (WM3001HWA). It makes very loud noise when the washer spins fast during spinning cycle. What could be the issue?
@rakape7867 жыл бұрын
Tks too much , very usefull for me
@1688jose4 жыл бұрын
Buen video pero no reparo la falla de la fuga de agua
@claudio1965h5 жыл бұрын
In my washing machine 3 of these sensors broke in a few months. The Vcc is 11.5 volt. What could be causing this flaw?
@wezy55104 жыл бұрын
Thanks for this video safe me $100 for service Call
@lagzdinalagzdina365811 ай бұрын
Can something cause the motor to cause resistance? Meaning if the power is off the drums spins freely and when the power is on immediately becomes hard to spin and creates resistance. Won't go in full spin cycle stuck on 12 mins! The motor doesn't have the sensor on it like in most videos!
@appliancepartspros11 ай бұрын
Have you checked the belt to make sure that is installed correctly?
@threedog229 жыл бұрын
Well, if you have an issue with the bearing and or the seal, this would not make the repair cost-effective. If you have to replace all three items, you are probably exceeding the 50% replacement cost of the machine.
@appliancepartspros9 жыл бұрын
Dave Harrison The paid labor is what makes changing the bearings and seals so expensive. The parts themselves are not that expensive.
@threedog229 жыл бұрын
While I appreciate all the information, and trying to help out the average homeowner, no homeowner is going to attempt a repair of this magnitude, nor would I recommend it. (As someone in the business for 25 years) You're better off replacing with a new machine, and certainly not one manufactured by LG.
@appliancepartspros9 жыл бұрын
Dave Harrison The bearing and seal video is a popular video, many people are doing the repair!
@threedog229 жыл бұрын
I suppose some people have a few hours to kill on weekends. More power to them!
@superwash95552 жыл бұрын
Hi ..i have 18kg front loading washer and is it differ this part for my washer or same 6501KW2002A ?
@selasstecnica6 жыл бұрын
Como testar esse motor diretor
@appliancepartspros6 жыл бұрын
Se isso estiver quebrado, você pode obter um código de erro "LE" e a máquina de lavar roupa pode não funcionar corretamente. Se você precisar de mais ajuda, pode ligar para o nosso número de telefone 1-877-477-7278 ou conversar conosco no nosso site www.appliancepartspros.com/.
@ericpham82053 жыл бұрын
that rotor is space propulsion readied.vwas it a leak
@ashokdobariya65675 жыл бұрын
Thank you sir
@bikashtamang9539 Жыл бұрын
Sir. tt. Error. Coming. In same. Washing machine 18 kg. It says. Thermostat problem. But i change it but its not working
@Gmerg8956 жыл бұрын
This is awesome !!! :)
@appliancepartspros6 жыл бұрын
Glad we could help!
@David-zt4qe5 жыл бұрын
Is that what the stuff is called blue thread sealer?
@user-kj8jc2qw5h3 жыл бұрын
How to check this part
@scott90469 жыл бұрын
Just wondering if the sealant you use is a "Loktite" type or more of a teflon tape type product?
@appliancepartspros9 жыл бұрын
Scott Giggie We used the liquid blue thread lock. Hope the video helped you get the washer fixed!
@reginavsq8 жыл бұрын
My neighbor replaced the sensor for me the other day, but now the machine is making noises it didn't make before. It's sounds like a grinding noise along with a low squeal. I know he skipped the step where you unscrew the cables going to the sensors. Could that have something to do with it? He also didn't use liquid blue thread lock. Could that be the problem? Before I was at least use the machine once in a while, but now it won't even complete a spin cycle without getting an error code.
@appliancepartspros8 жыл бұрын
Sounds like something may not have been put back together right, if the bolt came loose the pulley would start to wobble. Without knowing what you have, I would suggest posting the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
@reginavsq8 жыл бұрын
+AppliancePartsPros Thank you! I took it apart again and figured out that he had snapped the sensor in the wrong spot. It's all fixed and running. No more LE error.
@reginavsq8 жыл бұрын
+AppliancePartsPros Thank you! I took it apart again and figured out that he had snapped the sensor in the wrong spot. It's all fixed and running. No more LE error.
@appliancepartspros8 жыл бұрын
Awesome, glad you got the washer all fixed up!
@David-zt4qe5 жыл бұрын
What does the code nd mean for a Samsung front washer?
@Tom-lc3cd2 жыл бұрын
what if the rotor won"t come off?
@zacharyjones70605 жыл бұрын
Why do you shut off the water while completing this repair?
@appliancepartspros5 жыл бұрын
We always recommend shutting off power and water before all of our repairs, just to be cautious!
@nikospetroulakis68885 жыл бұрын
please do you know stator 1kw max 2kw 220v
@stan_senior9 жыл бұрын
I have a GE WGT9350C0PL. I replaced the entire stator assembly because of the hall sensor. This part looks like the exact same hall sensor that is on my GE washer. Are they compatible?
@appliancepartspros9 жыл бұрын
stan senior Unfortunately we cannot cross reference from brand to brand. I would suggest getting the one that is called for by the model number of the appliance.
@stan_senior9 жыл бұрын
Thanks for your reply.
@MyNycable9 жыл бұрын
Do I have to disconnect the connecting wires to replace the sensor? I'm having a hard time disconnecting one wire. I'm squeezing it but it's not disconnecting. Almost broke my nail lol.
@appliancepartspros9 жыл бұрын
MyNycable We showed taking the whole stator off so we could easily show you how to remove the sensor from it. You only have to remove the wire connector from the sensor and then change the sensor while holding the stator. I hope the nail survived!
@shawnmclin35686 жыл бұрын
AppliancePartsPros z
@electrojeshuareparaciones48355 жыл бұрын
Eso que le sacó que es???
@romell73 Жыл бұрын
I opened my rotor but I didn't find sensor and still the LE error on
@jbpeach1611 Жыл бұрын
Same here
@elijahhannigan43029 жыл бұрын
thanks .
@appliancepartspros9 жыл бұрын
Elijah Hannigan Glad the video helped you get the washer fixed!
@rockhard240710 жыл бұрын
what if it spins one way but not the other? thank you
@appliancepartspros10 жыл бұрын
You can post this question along with the model number on our repair forum and our techs will help you out!
@gauchinho3010 жыл бұрын
Não vai consertar o vazamento no retentor?????
@appliancepartspros10 жыл бұрын
No está seguro de lo que quieres decir por el retenedor? Aquí está el vídeo para el sello trasero y de los rodamientos: Washer Seal and Bearings (part #4036ER2004A and others)-How To Replace
@michelb6137 жыл бұрын
if the rotor position sensor doesn't fix it, is there a way to troubleshoot? is there a way to test the sensor (maybe the new one I bought is also bad...)
@appliancepartspros7 жыл бұрын
We'd be happy to help you troubleshoot, Michel. We can use your model number to look at schematics for your particular appliance to see if anything else could be causing that problem, and we can also talk you through checking the sensor. You can look here on our website to help you find the model number: www.appliancepartspros.com/modelnumber_locator.aspx You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We also have a free repair forum where the techs can help you troubleshoot the problem: forum.appliancepartspros.com/. We’re here to help 7 days a week.
@michelb6137 жыл бұрын
Wow! I wasn't expecting a response so quickly! That's great. My washer is a FAFW4011LW0. Any assistance is greatly appreciated. Thanks, Mike
@appliancepartspros7 жыл бұрын
So you're getting the LE error code, and you replaced the rotor position sensor, and that hasn't resolved it, correct? Does it have any other symptoms? Try double checking the wiring to and from the rotor position sensor and the control board first.
@michelb6137 жыл бұрын
Thanks for the follow up. Yes that is correct. I double checked the wiring and everything looks okay. The LE is the only symptom I see but it doesn't really do anything else because of the LE error. I can do the "no spin" cycle and that pumps out fine but anything else, fills the tub, appears to go to a cycle that requires spinning the tub and it never spins and it never gets any further. Thanks again
@appliancepartspros7 жыл бұрын
I did some more looking into it. There's not a definitive test for the RPS, so the next step would be to replace the harness for the RPS since there can be a connection issue that is not visible. If this does not correct the issue, there is most likely an issue with the motor control board.
@demaXxXx5 жыл бұрын
Would the rotor position sensor be bad when the tub spins out of round (oblong)? There is a 1" gap between the SS tub and the housing and a 1/4" pap on the opposite side. No bearing wobble, no bearing noise. I pulled the tub all apart, no front panel, no rotor, no water leaks, I'm ready to remove the SS tub to inspect if the shaft is bent but I'd rather not to. It spins awfully fast & sound like a jet. Model LG FrontLLoader WM2277HW 2004 model. All else looks fine & like brand new, we only wash 1 or 2 loads per week. Any help appreciated. (I spun the motor also by hand using a breaker bar and there is no noise) I did find the filter full of small & tiny strips of what appears melted plastic shaved pieces 2" long melted to drops of hard plastic. The only plastic damage I found man made & caused is behind the top weight to sit flat against the housing. The boot looks perfect.) Thank You.
@Allierae242 жыл бұрын
what did you figure out, I have the 2016 Samsung front loader washer. I've took it completely apart at least 4 times now. The bearings, water seal , spyder, shaft, splines, outer plastic tubes, all look brand new. I replaced the shock absorbers, cleaned the entire water system coming in and draining out, cleaned drain pump it's working fine. The wash and rinse cycle seem to work just fine. Every time it gets to the spin cycle it starts wobbling side to side and gets so bad the cycle stops for a minute or so and repeats the same process. I have noticed that the inner drum seems to be a little warped ( very little) that's my focus right now a in Hope's it will take care of the problem. I have SERIOUS DOUBTS that it will fix it as the machine itself is supposed to maintain balance even when there's an out of balance load. I know it's been awhile since you posted this comment, and it would be GREATLY APPRECIATED if you see this comment and share your Wisdom !! thx..
@oviedoreylara16034 жыл бұрын
Y el rodamiento?
@dickharper7 ай бұрын
What about the bearing?? 😲
@appliancepartspros7 ай бұрын
Are you looking for the bearing? What is the model number of your appliance?
@andycao86027 жыл бұрын
how to know the sensor was broke? what is symptom ?
@TippyPuddles5 жыл бұрын
The drum does not spin but the door lock can cause the same issue.
@MuhammadZubair-zubaire9 жыл бұрын
hey i need help i have lg direct drive washing machine motor till me how i can start it from external source i means not from power coming from machine control board its self i want to run it from outside power how many voltage i have to give ac or dc? and witch color wire their is same wire u can see in video red yellow and blue please help me thanks
@appliancepartspros9 жыл бұрын
+muhammad zubair If you cannot determine this by reading the wiring diagram you can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem.
@MuhammadZubair-zubaire9 жыл бұрын
sir acutely i have lg direct drive washing machine model no WD-14336AD it was not working i brought another one but the washing machine motor is okay i checked it now i need help from u that i want to use this direct drive motor in other experiments u just till me that their are three wires coming to motor red,yellow & blue i want to run this motor from external source of power just i need from u till me how many voltages ac or dc? i have to give and witch wires i have to use thankx
@appliancepartspros9 жыл бұрын
+muhammad zubair This is a model that is not sold in the US, we do not have any info on it. You can try to post it in our forum and see if anyone there is familiar with it or maybe contact a local tech who works on these and is familiar with the voltage, etc.
@MuhammadZubair-zubaire9 жыл бұрын
thanks for ur corporation
@pvks36054 жыл бұрын
Wats d prize of the sensor?
@ricardoperezverduzco18358 жыл бұрын
funcionamiento
@ricardoperezverduzco18358 жыл бұрын
funcionamiento de la lavadora LG TONNER
@behindthescenes33943 ай бұрын
he left that bearing in. What??
@appliancepartspros3 ай бұрын
We have a video on the bearing here: kzfaq.info/get/bejne/j5OVdNmgp6-ZaY0.html
@oscarmatamoros8697 жыл бұрын
How to know the symptom of this issue?
@appliancepartspros7 жыл бұрын
A lot of times you will get an error code such as LE, which will let you know the part has failed.
@TippyPuddles5 жыл бұрын
@@appliancepartspros I replaced the door lock that fixed this issue.
@rural_old_dude6 жыл бұрын
I replaced the part twice and the error came back after a few loads
@appliancepartspros6 жыл бұрын
Make sure that you're using HE detergent in your machine and that you aren't using too much even if you are. The "LE" error code can be caused by excessive suds in the drum. Otherwise, it sounds like it may be a different problem with your machine, then. We'd be happy to help you figure out what's going on! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number. You can use this tool on our website to help you find it: www.appliancepartspros.com/modelnumber_locator.aspx
@rural_old_dude6 жыл бұрын
AppliancePartsPros thanks for the response. We only use HE Persil and then only use just around a table spoon, something we learned after first sensor fail lol. Could the stator be bad?
@TippyPuddles5 жыл бұрын
I replaced the door lock and fixed the problem once. I'm back here to replace the sensor.
@alanwilcox46898 жыл бұрын
ok...... so if the rotator won't come off to the point that I had my 16 yr old son pushing on the front to balance it as I pulled on it with a fucking pry bar and it won't come off, then what?
@appliancepartspros8 жыл бұрын
+alan wilcox I have never had a stuck rotor before, they should just pull off. The rotor center is plastic but you could heat it with a blow dryer to see if that helps, just do not damage it with the heat.
@melisachristiansen886910 жыл бұрын
why you didn't change the bearing and seal ?
@appliancepartspros10 жыл бұрын
We did that repair in another video! You can find it on our channel or website.
@mtsflorida2 жыл бұрын
Why would you locktite something you are coming back to fix in another video? The seal popped off and the bearings are no longer protected and will throw out all the grease so that the whole rod abd assemble breaks apart. That's a $400 repair when all you had to do is repack with synthetic grease and replace with new seal. Now you can take everything apart including both bearings and spending a few hours putting it back together.