ASMR Soldering Lead Free Valves (1" and 2") | GOT2LEARN
Рет қаралды 43,969
Жыл бұрынAmazon affiliate links to all the products I used in this video:
AutoCut Pipe Cutter 1/2": amzn.to/2XlyqAn
AutoCut Pipe Cutter 3/4: amzn.to/3gPmhhz
Superior Tool 1/2" Cleaning Attachment: amzn.to/2kwBMBK
Pencil Torch: amzn.to/2U3OTaa
Fitting brush 4 in 1: amzn.to/45ELin6
Propane gas(Blue bottle): amzn.to/3tpWAOo
Lead-free tinning flux: amzn.to/2U3abEW
Flux brushes: amzn.to/2T8ROBc
Lead-free solder (Sterling): amzn.to/3ZT6Jzn
Flame protector: amzn.to/3tzkcQV
Abrasive pads: amzn.to/2XaY6kT
Pencil reamer: amzn.to/2tBuhKW
All-in-one deburring tool: amzn.to/3B9dLUv
DISCLAIMER: Got2Learn is NOT responsible for any damage done to a property of which the plumbing wasn't done by a professional, I do not recommend doing your own plumbing if you are unsure about what you are doing, always hire a LICENSED contractor when doing any type of plumbing so you can be covered by insurances if something does happen, these videos are for entertainment purposes only!
@RunOs3 5 ай бұрын
No talking, no squealing, no backstory, just showing how to do the job. I can’t think of a more perfect video. Thank you so much for making it.
@Got2Learn 5 ай бұрын
🤩🤩🤩
@edwardnino9896 Жыл бұрын
Your commentary provides useful information, it is missed!!
@ericsfishingadventures4433 Жыл бұрын
I used to do medical gas pipeline work and the fact this kind of information exist is actually amazing, well presented.
@Got2Learn Жыл бұрын
Sweet, thanks 😊
@d46512 11 ай бұрын
What is that? Like the oxygen inside hospitals?
@justCarner Жыл бұрын
I solder with my valves closed as well. People argue ventilation for leaving it open but that’s not a good reason. The best reason for closing it is to help keep the shape of the gasket where the ball valve closes. Great work, as always.
@Got2Learn Жыл бұрын
Good tip!
@theyhateme8763 Жыл бұрын
@@Got2Learn valve should be slightly cracked open. if you over heat the gasket blows out
@Inquisitor6321 4 ай бұрын
Ideally, solder ball valves in closed position. OR open when you need to vent the hot air from inside the pipe so it doesn't bubble out through your molten (fresh) solder joint. But DO NOT solder ball valves while they are partially open. That will ruin the valve. The only valves you can solder in the partially open position are: stop & waste valves; globe valves or gate valves. Happy sweating!
@shawnbush41 Жыл бұрын
Great video! Glad to see you uploading still!
@JimsEquipmentShed Жыл бұрын
Nice, it was interesting to actually see the time involved.
@Viper6-MotoVlogger Жыл бұрын
Well done mon ami. You are the master of masters 😁👍🍻
@juanceballos8423 11 ай бұрын
Thks, for the video that solves the debate on the other video!!
@ClippyC 10 ай бұрын
The lesson I learned here - take your time.
@Got2Learn 10 ай бұрын
Yes.
@Milkman1969 Жыл бұрын
Great videos dude! I have learned a lot.
@Got2Learn Жыл бұрын
Glad to hear it!
@brianhoffman5414 Жыл бұрын
Thanks man these can be helpful!
@michaeljohn29 Жыл бұрын
Well done 👍🏻👍🏻
@JasperTedVidalTale Жыл бұрын
Nice lead free video
@kele1264 Жыл бұрын
Thank you very much!!!
@z1522 9 ай бұрын
At 3:04, a gap appears at the top of the joint, suggesting poor flux or contamination, instead of the shiny continuous bead one desires. There might be enough solder inside to seal the joint, but I would worry that it could fail without the obvious continuous bead.
@lg3187 6 ай бұрын
its a large gap, need to go back and fill it in after it cools a little
@paulbauer5337 2 ай бұрын
Valve should be open during soldering as to not trap expanding air with a fixture or hosebib open.
@heinzotto1194 4 ай бұрын
Great video, exactly what I needed 👍
@Got2Learn 2 ай бұрын
Thank you, don't forget to share, it really helps the channel!
@lmzaadi Жыл бұрын
So relaxing
@Got2Learn Жыл бұрын
😴
@mayerlito 2 ай бұрын
Thank you a lot for your video, Excellent!
@Got2Learn 2 ай бұрын
Thank you, don't forget to like and share 😇
@MrGabriel1973 3 ай бұрын
this video is so interesting, especially for deaf people who really want to learn this job thanks
@Got2Learn 3 ай бұрын
You're very welcome!
@Got2Learn 2 ай бұрын
Thank you, don't forget to share, it really helps the channel!
@dingo5842 6 ай бұрын
Thank you!
@Got2Learn 6 ай бұрын
You are most welcome!
@user-mi9ls5fw3f 2 ай бұрын
Very helpful thanks
@Got2Learn 2 ай бұрын
Thank you, please share if you can, have a great day sir!
@CitizenShane 10 ай бұрын
Hey man i started using tinning flux, nokorode, and I'm used to using everflux and you have to thoroughly stir everflux before using. The tinning flux is so much thicker and pastier, do you need to stir it thoroughly as well?
@Got2Learn 10 ай бұрын
I leave it in the heat when I can.
@andrewc6385 6 ай бұрын
Been a while since u posted. Hope your doin well 🇨🇦
@Got2Learn 6 ай бұрын
Father had a severe stroke in August, so my priority is not to make videos anymore unfortunately :( Thanks for your concern Andrew!
@nefariousyawn Жыл бұрын
Whenever I see the logo for Oaty I can't help but think about oatmeal.
@Pete.Ty1 Жыл бұрын
👍👍👍. Thank you
@Got2Learn Жыл бұрын
🙏🙏🙏
@jifors 11 ай бұрын
How do you solder when you have a T fitting close to the valve. As in no pipe seen between one of the the T end and the Valve? Going to install a 3 valve bypass for my water softener. 1" pipe and valve.
@handydoc2531 Жыл бұрын
I am amazed at the neatness and precision. 1 question. I always thought that I was supposed to leave the valve open so as to not damage the seal. Am I mistaken? 😮😮
@Got2Learn Жыл бұрын
Thank you, it depends on the manufacturer, some manufacturers require the valve to stay open some require them to remain closed.
@felixsss9683 11 ай бұрын
Nepleteš
@phildivirgilio6286 Жыл бұрын
good job "how is your back"👍
@Got2Learn Жыл бұрын
terrible.
@davidh.8513 Ай бұрын
Good video as always! What keeps all that heat from ruining that Nylon seal around the ball valve? That is what I worry about!
@Got2Learn Ай бұрын
The amount of heat used to solder it ;)
@davidh.8513 Ай бұрын
@@Got2Learn OoooKay?
@learninglessons7428 6 ай бұрын
Can you do a video on "vertically" soldering larger size ball valve and pipes i.e. 2"? I understand its much more involved... Thanks!
@Got2Learn 6 ай бұрын
Already have, here's the link: kzfaq.info/get/bejne/grtpoqtzzbPKd2Q.html&ab_channel=Got2Learn
@victorhugorengifomera6517 9 ай бұрын
This solder could use in hvac pipe
@electrolatif 11 ай бұрын
What is the solder can ise for air-conditioning?
@dkaloupis75 Жыл бұрын
I have weld so far in my lifetime from 1" to 2" with map gas and for 1"under normal blow torch the small one 😂
@tristanquintus3200 4 ай бұрын
Hi and thank you for your many videos. They have been very helpful. I’m just beginning to learn some soldering skills and have a question for you. Regarding the soldering of the brass valve in this video. Will the heat from the torch potentially damage or compromise what appears to be a plastic seal within the valve?
@Got2Learn 4 ай бұрын
Thanks, check this video: kzfaq.info/get/bejne/mat8rcZqv9XUmIU.html
@tristanquintus3200 4 ай бұрын
Thanks for replying to my post. I watched your video using the link you provided. Very helpful, as usual. Fine work.
@Got2Learn 4 ай бұрын
@@tristanquintus3200 You are most welcome!
@mattmorrison5479 11 ай бұрын
I would love to know your opinion on the knew style shark bites. Sucks cause I work at a plumbing store and people don’t like the knew ones.
@Got2Learn 11 ай бұрын
Sharkbite Max?
@Lugenfabrik 11 ай бұрын
He did a video on the new shark bites.
@mattmorrison5479 11 ай бұрын
@@Lugenfabrik ima look for it thank you
@sigor2011 Жыл бұрын
What's with the silent treatment?
@AGhostInTheMachine Жыл бұрын
I thought that much pre-heat on the pipe and valve would've burned away the flux, but that doesn't seem to be the case. Is it because the Oatey in the green container is more heat resistant or something?
@Got2Learn Жыл бұрын
Correct!
@AGhostInTheMachine Жыл бұрын
@@Got2Learn I see, so would it be okay to just always use that type of flux for any joint instead of the other types? I'm always in a rush fearing flux burn, but you're way more patient. For an amateur like me, that would be a nice advantage being able to go at a more relaxed pace as shown.
@Got2Learn Жыл бұрын
@@AGhostInTheMachine for sure
@felixsss9683 11 ай бұрын
Kolik si v USA,nevím v kterém státu,vyděláš jako Instalatér za měsíc?Dik za odpověď.Hi Dalibor
@paulmanhart4481 2 ай бұрын
You closed the valve? I heard it should be open. How do you know? Also, you heated the pipe instead of the fitting. Why? Thanks, Paul
@Got2Learn 2 ай бұрын
That particular brand and model ask for the valve to be in the closed position when soldering, some ask to be half opened, some opened, it really depends the brand. As for why I heated the pipe, I explain that here: kzfaq.infoUgkxm1YH54kJ0Fwcwe0Udkrlg6NjX3Fh6TBQ?si=M5Wq_QQ4AETtOKIf
@FNPMSN 2 ай бұрын
why did u use oxy/actelyne torch on that 2inch? mapp gas or regular act. (b-tank) would b just fine.....
@Got2Learn 2 ай бұрын
I had the oxy/aceth setup, but yeah a btank would work just fine.
@keepingup2952 Жыл бұрын
Dang, what's that little blade tool you use for scraping the inside of the copper pipe called? Anybody know? Oh, I see it above, it's called a pencil reamer. Thanks!
@d46512 Жыл бұрын
Pipe deburr tool
@electrolatif 11 ай бұрын
Oatey 95/5 solder, is it good for refrigerant piping?
@Got2Learn 11 ай бұрын
Negative. You'll be needing silfos rods to braze those lines.
@Airborne490513 21 күн бұрын
I would suggest keeping your flux and brushes clean. May eliminate the couple voids. Otherwise pretty good video.
@nalalla6470 6 ай бұрын
Saw ur brother shouting you out in a tiktok comment
@Got2Learn 6 ай бұрын
Was it good or bad?
@nalalla6470 6 ай бұрын
@@Got2Learn it was good😂, it was a vid about how plumbers could be more successfull than doctors and then she mentioned you👍🏻 (it was ur sister btw, not ur brother, my mistake)
@Got2Learn 6 ай бұрын
@@nalalla6470 WOWWW, awesome!!!!!!!
@cm20506 7 ай бұрын
How much pressure can soldering points withstand?
@Got2Learn 7 ай бұрын
Don't go above 130lbs, anything over that needs to be brazed or threaded.
@cm20506 7 ай бұрын
@@Got2Learn I meant the fluid pressure inside the joints.
@georgevalente4223 Жыл бұрын
What? Cat got your tongue?
@mystuffseventyone5930 Жыл бұрын
Really though
@Lugenfabrik 11 ай бұрын
He’s shy.
@NonrevS 2 ай бұрын
We don't wanna hear someone talking bollocks
@suavemang 11 ай бұрын
Can you solder 2 inch with propane?
@Got2Learn 11 ай бұрын
Doable, not preferable.
@AsbestosBeard 2 ай бұрын
Please start posting again, i miss your content
@Got2Learn 2 ай бұрын
😔😔😔
@alext8828 Жыл бұрын
What was the purpose of this video? It totally escaped me. Great channel. Bewildering video.
@Got2Learn Жыл бұрын
No particular goal for once, just some soldering footage 😉
@alext8828 Жыл бұрын
@@Got2Learn Got it. Thanks.
@Michaeltubix 10 ай бұрын
How can I get into plumbing in Canada with zero experience or knowledge
@Got2Learn 10 ай бұрын
You need your plumbing certificate, no choice.
@ntgcanit1149 9 ай бұрын
Apply with Neptune meter installation, learn plumbing ")
@timowe1691 11 ай бұрын
is youre discord still active ?
@Got2Learn 11 ай бұрын
Nah, got rid of it because no one knew how to use it, i'll be opening a Twitter account soon so people will be able to reach me much more easily, stay tuned.
@lightcapmath2777 Жыл бұрын
What does the LF mean??
@plumbbuild6517 Жыл бұрын
Lead free
@lightcapmath2777 Жыл бұрын
@@plumbbuild6517 Thank you......knowledge is power... DVD:)
@MF-vg3qt 11 ай бұрын
What happened to the "Hey, what's up guys? In this video I'm gonna show you..."? I miss the commentary.
@Got2Learn 11 ай бұрын
Next one coming soon ;)
@honolulu1476 Жыл бұрын
Why no voice ?
@Got2Learn Жыл бұрын
ASMR 😂
@oneyaker Ай бұрын
You got a massive gap at the top of the first joint. Why would you present this as an example of good soldering?
@sojiro288 Жыл бұрын
Trying out a new vid format? Either way love watching your vids hope you're doing well
@billmoody9736 Жыл бұрын
Lost your voice?
@ChadDuckboy001 Жыл бұрын
Love the no gloves
@jwag2708 21 сағат бұрын
For a moment there, I thought this was a glory hole vid. 😂
@Got2Learn 21 сағат бұрын
LOL, none of that here 😆
@Baudesign Жыл бұрын
As-tu perdu la voix?
@JS-bb2lo Жыл бұрын
First
@RustamUzoqov-rz8uz 22 күн бұрын
Самый умный из инструментов это тряпка.
@Emphasis213 11 ай бұрын
Videos not the same with out you talking.
@Got2Learn 11 ай бұрын
😎
@FNPMSN 2 ай бұрын
wow hes not very good
@Got2Learn 2 ай бұрын
results are at the end.
@VIPP79 3 ай бұрын
Jesus you should learn to solder properly before posting videos
@Got2Learn 3 ай бұрын
Here we go lol...
@ericknoesaavedra3030 5 ай бұрын
This guy itsnot professional, what about gloves to protect your fingers when deburing
@Got2Learn 5 ай бұрын
That's what makes me unprofessional?
Got2Learn
Рет қаралды 473 М.
The DIY HVAC Guy
Рет қаралды 478 М.
Got2Learn
Рет қаралды 3,3 МЛН