Thank you very much for watching and the good wishes. I will be running them as soon as I get them. Thank you again

Thank you for watching and commenting. They have done a fantastic job with the product and the price point is spot on. I go to sleep every night with the knowledge that I have no worries about reliability. I am glad that you are enjoying the inverter, I have enjoyed it. Can't wait to put the SolaX to the test.

Thank you very much. I appreciate you. I made the video for you. Glad it answered your questions

@@drsolar it definitely did, and just today my charge rate jumped to 25a. I'm going to buy extra batteries as you advised. Soon il be off the grid just like you. Dr solar i hope with your new endeavors it allows you to go more into solar panels and battery combinations as well. God bless 🙏 my brother

@@LekaLEL glad to hear it charging at full tilt. I am excited about the new direction that we are taking. Thank you brother. Remain safe and healthy

Thank you so much. I won't knock Deye. They will do what works for their brand. They want to move as many as possible. A high end Axpert model. The SolaX is a high voltage inverter. They offer you a complete solution. From inverter to battery. They have the sizing that fits our clients. As little as 3 kw and as much as 15 kw three phase. They have batteries that fit too. 3 kwh up to 9 kwh. We will only offer the 5.8 kwh. Wat I like is the X-ESS. Can be installed in as little as 30 minutes and comes with box that manages all your connections. Battery disconnect, PV disconnect, CT and RCD's

Thank you for watching and commenting on this video. I won't do a Deye video because it is no longer the primary inverter that we install.. The time of use allows you to do things like what you wrote about.

You can do time of use.

You rock. Thank you so much. I am so excited at the opportunity to work with them. Please help me grow the brand

@@drsolar we will definitely support you.

Thank you for watching and commenting. Tell your supplier to update the inverter firmware.

Touch the thing that looks like a sprocket top right corner of the screen

Good morning Amir I am stumped. Double check your breaker and connections. Check the breaker for continuity. Then check your wiring. If it checks out confirm polarity. LNE. If that fails use the gen port to eliminate that the inverter is the problem. Start with the breaker and your connections first.

Beeps when it is doing what. What is the battery percentage when it is doing this?

Thank you

Thank you for watching and commenting. Check to make sure that they have the same firmware versions

Your charge and discharge settings are too low. Look on inverter and see what it is telling you it should be, then do 20% less. On the main screen touch battery and read BMS data

Thank you for watching and commenting. I have no experiences with welders so I can't answer with authority. However on some installations we have done they have been accidentally used without issues. Don't forget to subscribe.

Thank you Sir

never mind, i should watch till the end :)

Thank you for asking. They have a different model. They are more focused on moving product and not on relationships. SolaX Power wants a quality network with very good support for the product. Thanks for watching to the end

@@drsolar , that's the problem from where I am Deye, doesn't really have a certified distributor. Different sellers sell Deye and if there is problem or repair no guarantee if they will support. If you come across shady resellers your in bad luck. Buyer may be responsible in shipping to Deye. If they have a certified distributor with good after sales support that would be ok at least. Luxpower, they have distributor and service support. Good to know you closed a deal with a new company solax that cares for you.

@@nestyplus that is what SolaX wants to avoid. I get lots of phone calls and emails from people looking for support for the Deye inverters. SolaX Power wants the support to be provided by trained and dedicated providers

Use battery voltage..set you lbco to the corresponding value that matches 50 %. I have not used a lead acid battery in over 3 years so I don't remember that number.

@@drsolar ok thank you very much.. Please one more question how can i set the inverter to get the grid first when come and then when the grid off to get pv?? Another questionWhat is the span life of acid battery in solar system with 50% of discharge?

Thank you for watching and commenting. I am not aware of any

Yes you can

Thank you OGW

Honestly I am not 100% certain but my guess is that you don't want to export any production you have to reference it somewhere. So the CT that measure the grid or your load that consumes. I will get a smarter answer for you

That is correct. In addition, if you set the Deye inverter to Zero export to CT, the inverter will work as grid tie inverter, however it will not allow your generated power from solar or battery to export back to the grid. The solar power or battery power will be be distributed to all loads inside the house as gried tied principle. Having said that, the load/output of the inverter also works as gridtied. Should there be a power failure, the built in offgrid inverter of Deye will turn on and distribute the power to the load/output of the Deye which takes about 4ms switching time similar to UPS function. Any excess solar power production will charge the battery depending on the SoC, or you have an option to activate the smart load to dump the power. As for the Zero export to load setting, this works as purely off grid inverter. Even there is a grid input, the solar power production will only be distributed to the load/output of the inverter. This setting is very suitable if you wish to live offgrid similar to Dr. Solar. Hope this helps.

@@onortrebor Very clear explanation. Do we still need to install a CT if Zero export to load is set ?

Yes it is normal for the internal and external fan to come on

Thanks for watching and commenting. Do you have the generator connected to the gen port?

@@drsolar Yes it is connected to the Gen port.

Check your time of use settings

Thank you

Low battery voltage. What type of battery do you have? What did you set you Gen or grid charge voltage or percentage to?

@@drsolar Greenrich Battery 51 v

@@benmatus1503 double check that you have BMS communication

Check your grid input breaker. Thank you for watching and commenting

Hello Glen thank you for watching and commenting. There are so many videos on this subject. Deye has one on their channel.

Do you have a battery?

Thank you for watching

Should I say congratulations?

I need more information from you. Please explain what you are looking at and what you are looking to acomplish

@@drsolar thank you for your reply, i added the batteries but i can see a 220 V load on the home icon, im checking if there is any malfunction in the electronic part or i missed any software configuration. Thank you

@@abdobejjani2699 what are you expecting to see. I don't quite get what the problem is.

When u add the batteries, turn on the inverter you should see the V of the batteries which is 55.6 lets say and the output (which its call LOAD or Home icon on the inverter screen) 220V, im still getting a 0V for the output, that's it dear

So im not getting an output at all even i have added the batteriea

I set the time from 00:00 to 05:00, Grid Charge Checked. But still during that time, my battery is still discharging.

What percentage did you ask it to start charging? Go to your battery settings and where you set the start charge current, check the start percentage. If your battery does not get to that number it won't charge. Please share my videos with your friends and family and if you have not subscribed, do

BMS is connected

Thank you for watching and commenting. What inverter are you using?

@@drsolar nitrox 5kw

The same factory makes them

Someone already covers your market. Thank you for watching and commenting