Bass Tracker Overhaul

Bass Tracker Overhaul - EP10

Рет қаралды 10,506

4 жыл бұрын

Overhauling a bass tracker pro 17, new storage, new flooring, new electronics, marine vinyl... the whole nine yards!
Follow the facebook and instagram pages to stay up to date!
Facebook
/ putemdownproductions
Instagram
/ putemdownproductions
Equipment I use:
Big Camera - Sony NX5U
DSLR - Canon 60D
Lens - Sigma 17-50 F2.8
Lens - Sigma 70-300 F4-5.6
Wireless Mic - Sennheiser EW 112P G3
Shotgun Mic - Rode Video Mic Pro
Rode Video Micro
Action Cams - GoPro Hero 3+
GoPro Hero 4 Session
Tactical 4.0
Editing - Macbook Pro 15"
Premiere Elements 2018

Пікірлер: 30

@MrPapi63 4 жыл бұрын

Awesome, the boat has come a long way from when you got it. Great video. Keep up the great work.

@terrymccorkle1674 4 жыл бұрын

Looks great. Good job

@southwests5508 3 жыл бұрын

id be interested in buying one of those beauty panels u made/had made for the console.

@PUTEMDOWNProductions 3 жыл бұрын

It was pretty easy to make, i just traced the plastic panel onto a sheet of diamond plate, cut it out and bent it on edge of my bench with clamps and a rubber mallet

@hikefar82 4 жыл бұрын

Love the video pretty jealous of your boat🎣

@Myotis05 4 жыл бұрын

Add small rubber pads under livewell lids. This will level them out and reduce the sound when they close.

@raymaylone8563 3 жыл бұрын

Also you might want to check out Jimmy Houston outdoors video on Livewell vents to keep water in your live well coolWhen running from one spot to another minor on order to install in my ranger

@raymaylone8563 3 жыл бұрын

I’ve been watching the entire series of your boat restore and wondered if it would work better for you later on in the future for the rear deck to turn it around so that it opens towards the engine? My tracker lid for the back deck open the same way and makes it really tough to do anything if you happen to be on the water and need to get into that back deck and do it safely In rough water conditions. Then the lid won’t hit the rear pole seat. Fantastic job

@PUTEMDOWNProductions 3 жыл бұрын

Thanks for watching, i contemplated turning that lid but decided to leave it factory direction and its not horrible to get into on the water had to do it not too long ago when i forgot to turn on my power to fuse panel

@bigdwg8637 4 жыл бұрын

Rubber weather seal will fill the gap on the doors.

@naterosswog9798 Жыл бұрын

Do you have a video about cutting and bending the diamond plate panel? I am trying to do it for mine but don’t know how to co about cutting and bending

@PUTEMDOWNProductions Жыл бұрын

I did not video it but i just used the plastic stock plate as a template and cut it out then clamped it down on edge of bench and bent it over the edge with a mallet

@justinlargent5260 2 жыл бұрын

You did a awesome job. What did you use to go around the latches the seals that look like rubber around the top. Thanks in advance.

@PUTEMDOWNProductions 2 жыл бұрын

There were seals that came with the latches

@justinlargent5260 2 жыл бұрын

Ok thank you.

@brandonpatterson5705 4 жыл бұрын

Looks amazing man 2 weeks left of work and your done. Lol can't get over how awesome your console turned out. Could you possibly show how to wire the bilge pump up properly in case someone buys same switch panel?

@PUTEMDOWNProductions 4 жыл бұрын

Once i get my new matching switches i will show it

@PUTEMDOWNProductions 4 жыл бұрын

The bilge was also wired correctly just the motor was seized up.... took me 3 hours to figured that out haha

@brandonpatterson5705 4 жыл бұрын

@@PUTEMDOWNProductions that's frustrating however at least you found out what it was. Some guys will buy a new one anyway and throw old one away when it still worked. Congrats on the boat it looks awesome. Can't wait to see your storage across along with your rod locker.

@earnest6 3 жыл бұрын

where did you buy your clamps? How many feet of vinyl did you order

@PUTEMDOWNProductions 3 жыл бұрын

36ft of vinyl, bought clamps at menards

@andrewbieschke7785 4 жыл бұрын

Love the video. I have a 1992 Pro 17. I have to upgrade my fish electronics. Do you think I could mount a Helix 7 with a Ram mount where you have your 5 inch Humminbird?

@PUTEMDOWNProductions 4 жыл бұрын

You would want to have wood or aluminum underneath to support it, would be alot of stress on just the fiberglass...

@kylemickelsen7661 4 жыл бұрын

My vinyl delivers today, finishing sanding today. Do you have any recommendations before installing the vinyl to maybe fill in some of the gaps, and make the doors sit level

@PUTEMDOWNProductions 4 жыл бұрын

No good recomendations i filled alot of the gaps with the adhesive as for leveling the doors mine are no worse than factory after looking through photos, could stick aluminum spacers in there to get them perfect but i think mine looks great without any additional work!

@jimfitzgerald9761 3 жыл бұрын

Maybe I missed it in your video but where did you get the aluminium trim plate cover for the dash? Your books looks great bud! I just purchased a 93 TX17 so I have some upgrades to do!

@PUTEMDOWNProductions 2 жыл бұрын

I made the dash from a sheet of diamond plate.

@terrymccorkle1674 4 жыл бұрын

What was the radio you installed. I lost where I had written it down

@PUTEMDOWNProductions 4 жыл бұрын

Boss brand