Part 2: • Beginner Tutorial 2 (A... Part 3: • Beginner Tutorial 3 (A...
Пікірлер: 53
@Fafancina7 жыл бұрын
Im using 2006 autocad and just switched to 2017 and its mind blowing how they almost kept it same and simple
@elie01748 жыл бұрын
how come when I try to draw my graph uses huge units like when I type 30 I get a tiny line but when you do it you get a big one and im on the same zoom
@dritantiran19567 жыл бұрын
hello. thank you very much for the lessens. were an very helpful. my question is, can i use auto cad 2017 for create furniture like cabinets, wear drops etc?
@mijachin7 жыл бұрын
Hello anyone who was having a problem with not being able to draw a door or window to the wall of the house, please press F6 and your dynamic UCS should come on to let you do it.
@MaZEEZaM7 жыл бұрын
Thanks :)
@philiprosal59827 жыл бұрын
how do you draw on the z axis... i cant draw the door
@LesChroniquesDeGeorge7 жыл бұрын
Thanks dude! Your tutorials are awesome :)
@mastersodicc17 жыл бұрын
To be able to draw the door you need to open the 3D status bar and activate "allow dynamic UCS". Took med 30 minutes to find it....
@natpetyova62157 жыл бұрын
oh jacob thank you!
@natpetyova62157 жыл бұрын
Thanks Kristo Suur
@philsweeney87877 жыл бұрын
Great tutorial, many thanks :)
@zachfosterWeeklyVlog7 жыл бұрын
Stumbled across this video man this took me back 5 ish years to high-school
@Grieldo8 жыл бұрын
Thanks! This is a big help.
@Sam-um4mh7 жыл бұрын
good vid :) you earned a new sub!
@BalkanManic8 жыл бұрын
Really good teacher
@timwatson39867 жыл бұрын
Fantastic video man. Thank you
@rahim1867 жыл бұрын
Great
@Ianrob11007 жыл бұрын
This says 2017 but the video refers to 2016.. ?
@tonystone77 жыл бұрын
Yeah, i can't get past making the door. I'm not sure why, but when i create it, it goes up the Y axis instead of the Z axis. It is so frustrating trying to figure out how to fix this.
@SatelliteHeart0207 жыл бұрын
Very helpful i subbed!
6 жыл бұрын
Wonderful
@jordanhargraves18088 жыл бұрын
so when I hold shift like you say it doesnt actually rotate. it just does the line selection thing
@trenthaines38868 жыл бұрын
shift and move your mouse while pressing the scroll button down, its kinda confusing
@jordanhargraves18088 жыл бұрын
+Trent unknown oh thanks. i figured that would be the case. was soing this just using the mouse pad on a laptop
@savannahwise70587 жыл бұрын
+Jordan Hargraves did you have to use a mouse on this? I'm using the mouse pad on a laptop also and I've having the same problem. I also tried using a mouse but it didn't work either.
@matt300207 жыл бұрын
This would be a brilliant tutorial if the door thing would work. everytime I try to draw it it just goes all over the shop!
@MrZCAD7 жыл бұрын
Make sure you are on the right surface. It will light up if you are. If you are having trouble try drawing it from an edge and then moving it use the MOVE command.
@Broabeluciano7 жыл бұрын
Nice. Thank you
@martinkwok87 жыл бұрын
how come when I draw the door the door went to the side of the wall?
@MostWantedxM2Mx7 жыл бұрын
I wanted to know is this worth taking for summer school? It's either Auto Cad or Mathematics so I could transfer in the winter(quarter system)/spring semester
@MrZCAD7 жыл бұрын
I've used this a lot more than I've use all the math I've learned.
@silentwalker48967 жыл бұрын
nice :) love it
@lesmouflettes7 жыл бұрын
Hello, I can't make the "offset", it's isn't working, but I don't understand why. Could you help me please? (Sorry for my english, i'm french)
@uglyonebeyou7 жыл бұрын
moi non plus ca n a pas fonctionné on a pas exactement les meme command bizarrement, moi j ai refais une Ligne un peu plus grande et un PEdit pour joindre
@akrammlt7 жыл бұрын
DECALER in french autocad
@govindaprasad46217 жыл бұрын
thanks sir very hlp fl
@madcapper68 жыл бұрын
Everything was going fine until I tried to draw the door @ 8:43. If I click the bottom line of the building pad to start the door, it draws it on the X,Y plane, or across the floor. In order to draw it vertically, or on the wall, I have to click the top line of the building pad. What is going wrong? When you drew it, you mentioned there's a little green tool of some kind. I can't see it in the vid. Are you referring to a snap tool of some kind? I have snaps on, with active snaps being Nearest, Perp, Endpoint, Midpoint, Center, Quadrant, Midpoint and Extension. I guess I can draw the door starting from the top of the building pad and then just move it down 1 unit but that takes an extra step and the whole objective for me is to learn how to take extra steps out of the drafting process. Thanks.
@spencey188 жыл бұрын
i might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
@crisulina4ever8 жыл бұрын
i tried it and it still doesn't work...:(
@tinotendamatema35418 жыл бұрын
thanx really worked for me
@fogeedup8 жыл бұрын
Thank you so much, it worked
@wxwxn31867 жыл бұрын
whoaa, thanks i have the same problem
@jordanhargraves18088 жыл бұрын
so another question. tried drawing in the door but whenever i try starting from the base it automatically snaps to one the corners of the house. is there a setting im suppose to turn off
@fogeedup8 жыл бұрын
might have found your problem brother, press F3, it will be your snap cursor. if your still having trouble look at your bottom right toolbar you will see a square with a green dot, unclick that and youll be able too draw your door with out it snaping to the X,Y
@jwalk3rman7 жыл бұрын
What unit am I supposed to set it to? Mine is on millimeter
@Fafancina7 жыл бұрын
If you're not from USA metric if you are from USA then inch
@joec10297 жыл бұрын
Or if your from USA and want it to make more sense, metric.
@mrcool98377 жыл бұрын
not working with the offset and there are different units on my auto cad compare with yours.
@vivianlau50558 жыл бұрын
I would like to ask I m using mac 2016 version and , shift key doesn't work .Is it i did something wrong or there is any key for rotate functions ? thanks!!!
@darlingmyo27 жыл бұрын
The polyline ruined everything. I couldn't extrude upward because autocad didn't like the polyline
@mrcool98377 жыл бұрын
Not working for me as worked for you.
@mrcool98377 жыл бұрын
not working with the offset and there are different units on my auto cad compare with yours.