BEGODE Master V4 Mods Overview Feb 2024
Рет қаралды 3,852
4 ай бұрынbuy the plans to build this at EUC.jc84.com
@EUCRAZY_AU 4 ай бұрын
I have rode this Master and it feels amazing for a BEGODE.
@busybody1474 4 ай бұрын
You have more engineering knowledge than the entire engineering staff at Begode😂
@c300theone 3 ай бұрын
Nice video.. great mods!!!
@EUC-Custom-Power-Pads 4 ай бұрын
Looks great 👍
@whileistillcan9338 4 ай бұрын
Brilliant upgrades
@leonardpallardy8167 4 ай бұрын
👌👌So nice, very awsome job !!!
@suppahero9861 4 ай бұрын
Thats pretty nice
@MegoRaiD 4 ай бұрын
Класс! мне нравиться очень продумано, теперь думаю себе приобрести 3д принтер.
@jc84com 4 ай бұрын
Thankyou, 3d 🖨️ are awesome 😎
@c300theone 3 ай бұрын
Did you 3d print the seat yourself? If yes.. where can I find the stl file?.. thanks in advance
@jc84com 3 ай бұрын
OG Sherman Seat slightly modified The wheel now uses a pitbike seat form 30$ AUD ali express
@Gasper4K 4 ай бұрын
I've noticed in your previous videos, you mentioned how the pedal hanger was clamping too hard on the slider tubes causing binding. My extreme feels sluggish, as if the up and down resistance is high. I checked the extreme and it appears they have a solid piece of metal in the tube at the bottom where the pedal clamps are, which I assume addresses that problem. Then I also noticed you mentioning the motor spacer, and how you were going to sand them down a little bit. Did you end up doing so? If so, did it help? When I pushed my spacer in, it took some pushing to get it in, do you think I should also try sanding those spacer a little bit to fix the alignment?
@jc84com 4 ай бұрын
Yeah I sanded the motor bracket spacers to make them a bit thinner. As they are easy to re make in laser cutting and different supplier stock will vary slightly. Recommend removing the linkage to check movement flow. Especially if the unit has had some time to settle in. See where it's binding and make changes as needed for smooth motion.
@rowrows6096 4 ай бұрын
@julianjc84, impassive mods! I have same issue with my pedals Master v1 being too angled steep. I noticed you ground down the metal to make pedals flat , what tools could I use or other options to resolve this? Appreciate your help.
@jc84com 4 ай бұрын
Angle grider with sand disc Or Manual file and effort
@oghmard Ай бұрын
Where did you get the plans for this, I want to recreate for my begode t4!
@jc84com Ай бұрын
Measured the unit EUC.jc84.com
@Roskellan 4 ай бұрын
A question: do you think it's possible to put the "Master Pro Pedal Holder" and "Master Pro Pedal Adjustment Base" on the Master to lower the pedal height???
@jc84com 4 ай бұрын
Not familiar with the adjustment hanger device. However most things are possible.
@Kekafuch 2 ай бұрын
What are the size for the stanchion tube bushings on the EX30?
@jc84com 2 ай бұрын
id30 OD34 L12
@thomaslange1004 4 ай бұрын
Wow I have a v4 as well.. those handles are sick. I wish I knew where to even begin on how to get that on mine. Awesome work man. Also is that a Sherman half seat stuck on the back there? I am really tall and seated riding is uncomfortable I was using a yoga block but I didnt like the look, so I am looking for something better.
@jc84com 4 ай бұрын
Thankyou. Indeed og Sherman seat on back. It's needs to be more forward. still working out it's position. The 100mm stanchion mod increases stock seat height 30mm And then the og Sherman seat height too I'm 183cm tall and it's very comfortable seated height
@user-dk3ih5ok6k 4 ай бұрын
is this the updated master? looking at a purchase and it states updated version however states nothing about the updates on this wheel...yes ,my first purchase of a wheel and that is why i am asking.
@Audiboxx Ай бұрын
Whatsup with the 70mm or 100mm handles? If I have a regular begode master should I use the 70mm version?
@jc84com Ай бұрын
Factory stock master is 70mm travel And use the 70mm handle config. 100mm master, when you install custom +30mm longer stanchion poles to accommodate more travel (100mm). It adjusts the position of the batteries -18mm from the top and +12mm up from the pedals. That should explain the 70mm and 100mm
@Audiboxx Ай бұрын
@@jc84com Did you just paste some velcro on the battery to get those pads on there? I sure hope the stock pads still fit after I put these roll cage handles on my Master. I dont know how to get other pads on without buying a whole new pad system.
@jc84com Ай бұрын
@@Audiboxx you'll have to cut the corner bends off the stock pads and add some Velcro. Yes my pads are held on with Velcro, clean the boxes and pads with isopropyl, dry and adhere.
@pridetv 2 ай бұрын
Where did you get the front handle? Love it.
@jc84com 2 ай бұрын
EUC.jc84.com
@simongyromobiliste4522 4 ай бұрын
Nice work. Will the kit be available for purchase or only the stl?
@jc84com 2 ай бұрын
EUC.jc84.com
@Esk-be8kd 4 ай бұрын
I need that front handle
@jc84com 4 ай бұрын
EUC.JC84.COM They will be available there soon when I am happy with the Masters Final design.
@mbelozerov 2 ай бұрын
How can I buy your handles?
@jc84com 2 ай бұрын
EUC.jc84.com
@TeamBlindMouse 4 ай бұрын
source for stanchions ?
@jc84com 4 ай бұрын
I got random tubes on AliExpress and cut myself However Hou Ningning also makes and sells pre cut
@doubleSGtrouble 4 ай бұрын
Do u think this 100mm slider mod can be made to master v1?
@jc84com 4 ай бұрын
I would suspect so. I don't believe much on any core frame changes changed between v1 and v4
@doubleSGtrouble 4 ай бұрын
How can i contact you? Need to ask you something 🙏
@jc84com 4 ай бұрын
@@doubleSGtrouble m.me/julianjc84
@aggressivecalm 4 ай бұрын
Get a Lynx. And show me how to make it better. Please. Thank you.
@jc84com 4 ай бұрын
I'm too poor for a lynx
@blackw0rx Ай бұрын
feel free to start with the shitty axle that breaks to pieces after one or two months of jumping. You're welcome :D
@lostday5964 4 ай бұрын
когда можно купить
@jc84com 4 ай бұрын
Not ready for release yet
@jc84com 2 ай бұрын
EUC.jc84.com
Immersed
Рет қаралды 89 МЛН
Riwright Video Productions
Рет қаралды 1,4 М.