Behringer Crave + TD-3 combination using CV tutorial. Patch Ideas
Рет қаралды 88,569
Күн бұрынThe combination of Eurorack CV ins and out on Crave and TD3 is great field for new modulations and two sequences (or timbres) from these synths cooperation. Add this ideas to my previous tutorial and fall into modular frenzy.
If you like my patches or sequences for these synths, you may get them:
📻 Patches and Sequences for Behringer Crave
💽 Patterns for Behringer TD-3/TD-3-MO
Everything is here: antonanru.sellfy.store/behrin...
Contents:
00:00 Introduction
03:36 TD-3 Gate Out --- Crave Hold
05:19 TD-3 Gate Out --- Crave Reset
08:40 TD-3 Gate Out --- Crave Env Gate
10:15 TD-3 Gate Out --- Crave VCF Cutoff (+attenuation using Mix CV)
11:44 TD-3 Gate Out --- Crave Osc Mod (+attenuation using Mix CV)
13:08 TD-3 CV Out -- Crave OSC CV (+combo with TD-3 Gate Out -- Crave Hold, Reset, Env Gate)
14:50 TD-3 CV Out --- Crave VCF Cutoff
16:31 TD-3 CV Out -- Crave LFO Rate (LFO -- VCF Cutoff)
18:22 TD-3 CV Out --- Crave VCF Res
19:18 Crave LFO Tri --- TD-3 Filter In
20:47 Crave OSC Saw --- TD-3 Filter In (+attenuation using Mix CV)
23:17 Crave Noise --- TD-3 Filter In (+attenuation using Mix CV)
25:18 Crave VCF --- TD-3 Filter In (+attenuation using Mix CV)
antonanru.com/
#behringer #crave #behringercrave #303 #behringertd3 #tutorial #td3mo #tdmoddedout #td3modout #modular #patches #eurorack #techno #jam #semimodular
@AntonAnru 4 жыл бұрын
📻 Patches and Sequences for Behringer Crave 💽 Patterns for Behringer TD-3/TD-3-MO Everything is here: antonanru.sellfy.store/behringer/
@IgorPodobaev 3 ай бұрын
Эхх, жаль не купить из России.
@AntonAnru 3 ай бұрын
Можно купить. Напишите на почту
@paulwhiting1731 Жыл бұрын
It amazes me that Behringer doesn't have video tutorials featuring these ideas. Thanks to you they must be selling many more instruments. Excellent work Anton.
@AntonAnru Жыл бұрын
Thank you for the feedback
@chadmwest 2 ай бұрын
Can confirm :)
@evh3305 3 жыл бұрын
"A few moments later..." whole wall of modular synths.
@AntonAnru 3 жыл бұрын
At the moment i limit myself with semi modulars
@technokind1503 2 жыл бұрын
🤣
@333baxter333 2 жыл бұрын
It's a slippery slope
@titan0857 Жыл бұрын
True story.
@MetzgerDarkAmbientQC 4 жыл бұрын
Nice ! Been waiting 4 months to get the Crave I ordered and because of this video I might get the TD3 finally. Great sounds !
@AntonAnru 4 жыл бұрын
You will have a great fun
@pabloocampo2056 4 жыл бұрын
Really good info mate! Clearest I’ve seen in the internet so far!
@AntonAnru 4 жыл бұрын
Thank you
@K.KILLORAN 3 жыл бұрын
That interplay at 20:20. Love it.
@calebrocha7518 3 жыл бұрын
It's really helpful that you post the output --> input info on the screen
@AntonAnru 3 жыл бұрын
Glad that it helped
@mrbreaker101 4 жыл бұрын
This all sounds really good
@jacksonueland 3 жыл бұрын
Super creative patches, very nice
@AntonAnru 3 жыл бұрын
Thank you
@brianwilliams3621 Жыл бұрын
Hi Anton, I just found this video. Top stuff. I have your Crave patches and will now be plugging cables between my TD-3-MO-AM and Crave. Until now I have just synced them via MIDI and SYNC, so I'm looking forward to what comes out.
@AntonAnru Жыл бұрын
good luck with this combo
@hastysnailsound 3 жыл бұрын
Thanks for this video ! Lest's try it with my patterns
@AntonAnru 3 жыл бұрын
Good luck!
@DJdoublevision 4 жыл бұрын
i've been getting closer to get the TD3 to go with my Roland DJ505 ....and now guess what ...i want a crave now too ....thanks very much for this .....love the two of them together ,great sound ...thanks for this vid :)
@AntonAnru 4 жыл бұрын
Sorry for making you spend more money on synths)
@gru_day 2 жыл бұрын
So much fun! Music is amazing journey.
@JustMe-sn1zv 3 жыл бұрын
Very good video giving tons of inspiration! Thx!
@AntonAnru 3 жыл бұрын
You are welcome
@BenGeorge77 4 жыл бұрын
So inspiring. Just went and tried several of these.
@AntonAnru 4 жыл бұрын
good luck with it!
@bladelinemicrobladingparis1431 8 ай бұрын
Thank you for the tuto, love it
@basicinfo1640 4 жыл бұрын
I’ve got both coming in the mail this week! This video is a god send! Thank you :)
@AntonAnru 4 жыл бұрын
Have fun with new synth
@jonmaddison 5 ай бұрын
Really useful. Found via your webpage. Currently playing with this pair and this was really helpful.
@AntonAnru 5 ай бұрын
Glad to help
@PeresD 2 жыл бұрын
Great stuff my friend.
@AntonAnru 2 жыл бұрын
Thank you
@SketchieRecordsUK 3 жыл бұрын
great informative video👍🙌🙌🙌
@AntonAnru 3 жыл бұрын
💪🤘
@LuisTorres-qz5kr 2 жыл бұрын
Great Tutorial, thank you!
@AntonAnru 2 жыл бұрын
You're welcome
@yiyo8 3 жыл бұрын
Amazing video 👏👏👏👏
@AntonAnru 3 жыл бұрын
Thank you
@wildcat189 3 жыл бұрын
Awesome!
@hybridferret1969 4 ай бұрын
The TD-3 manual states the following regarding the Filter-In on the TD-3 FILTER IN - this input allows the connection of an external audio signal instead of the internal VCO oscillator. So this is not for modulating the Cutoff, but for allowing the use of the TD-3 filter with external audio signals.
@steveclifford6893 4 жыл бұрын
Wow! the Crave synth has funkiness! together with the TD 3 its even funkier! love it !! Thanks Anton !
@WackyJackyTracky 3 жыл бұрын
this is awesome!
@AntonAnru 3 жыл бұрын
thank you
@tomphillpotts 2 жыл бұрын
Nice work!
@AntonAnru 2 жыл бұрын
Thanks
@stephenmurphy8349 3 жыл бұрын
This is great - thanks!
@AntonAnru 3 жыл бұрын
Welcome
@manuelgonzales6483 2 жыл бұрын
I have those 2 machines thanks for sharing great ideas 😁
@AntonAnru 2 жыл бұрын
Have fun)
@C0DE8 3 жыл бұрын
Great Tutorial! THX :-)
@AntonAnru 3 жыл бұрын
Welcome
@exoterik23 4 жыл бұрын
Good video thanks, and good sounds too 😁👍
@DueWhatThouWilt 3 жыл бұрын
Jus ordered my TD3 can’t wait to hook up with my Crave!!!
@AntonAnru 3 жыл бұрын
Congrats with purchase
@DueWhatThouWilt 3 жыл бұрын
How do I send midi clock from Logic Pro to crave and td3
@AntonAnru 3 жыл бұрын
Via midi/usb
@DueWhatThouWilt 3 жыл бұрын
Right but in the settings how do I go about it?
@AntonAnru 3 жыл бұрын
Sorry, can't help with logic settings, i use Ableton. In td3 settings you should choose external clock
@marcopaganotto9125 3 жыл бұрын
Nice one man! I have these two lovely machines, so this info was very useful 👌
@AntonAnru 3 жыл бұрын
You are welcome
@lnterference 4 жыл бұрын
Спасибо Антон! Теперь точно беру обоих :)
@AntonAnru 4 жыл бұрын
Хорошей вечеринки
@technodrone313 4 жыл бұрын
having fun with my td-3 and microbrute connected up over cv.
@rexcellencemagee6729 4 ай бұрын
After I got the Roland T-8, I thought, that’s the td-3! I’m currently experimenting with those and two craves.
@Prankenpaule 3 жыл бұрын
Top 😀 thx a lot
@K.KILLORAN 3 жыл бұрын
I have these coming in the mail this week and I have the feeling the Crave is going to be a real gateway drug to dropping some coin on Mod
@funkyneil2000 3 жыл бұрын
I have the TD-3 coming tomorrow. It was bought on a whim but I get the feeling it could lead to an empty bank account!
@clay_oakley 3 жыл бұрын
@@funkyneil2000 got it too a week ago and I want more already...it really is a wormhole
@rfish2 3 жыл бұрын
And!!? How is it???
@martinjames7847 3 жыл бұрын
Yup. I bought one a year ago and ended up DIY building a whole eurorack modular of about 30 modules. I knew nothing about electronics before I started, and might have gone a little mad in the process. My TD3 arrives tomorrow...
@director2bob Жыл бұрын
you need a detox yet? I just ordered a roland TB-03 last week and just saw this guy and his videos and 100% going to buy these two devices and can always sell the Roland TB-03. But the sounds these two make when working together is dope cool. Just hoping you are still having a good experience with this gear.
@manuosfp Жыл бұрын
Nice, thanks
@AntonAnru Жыл бұрын
You're welcome
@gchristyer 4 жыл бұрын
Superb !✌️😁👍🇬🇧🙏
@unclemick-synths 3 жыл бұрын
Good video.
@AntonAnru 3 жыл бұрын
Thank you
@MrSwisstoful 4 жыл бұрын
Great stuff
@AntonAnru 4 жыл бұрын
Thanks
@andronaut 4 жыл бұрын
Why tf would anyone dislike this? Thanks a lot, Anton, your videos really help me understand my Crave and TD-3 better. Subscribed for more :)
@AntonAnru 4 жыл бұрын
Welcome to my channel
@cprovenzo 4 жыл бұрын
Nice!!!!
@AntonAnru 4 жыл бұрын
thanks
@cthlos 3 жыл бұрын
Nice tutorial. Thanks! Looking forward to mixing these devices myself.
@AntonAnru 3 жыл бұрын
Thank you
@director2bob Жыл бұрын
I am ordering both of these today because of your videos. I think these will sound so nice with my Moog Sub 37. I plan on buying all your downloads for ant of the dear I own. I forgot if I asked you if you tried the TD-3 MO the orange TD-3 and if you think that's a better unit to purchase. Thanks again for your channel. I love what you are doing for us!!!
@Cysubtor_8vb Жыл бұрын
Gonna have to try some of these out with my TD-3 and K-2, though, the latter's Hz/V pitch CV probably will reduce the number of options.
@donnychilner8385 4 жыл бұрын
A divider? You can change the pulse on the td3. Im looking at getting this.
@fleebschlehm2467 3 жыл бұрын
Very informative and entertaining Thank you! Are there running the identical sequences on Booth mashines? Each seq. has the Same Notes programmed? Cause i dont get it 100% 🤔
@AntonAnru 3 жыл бұрын
Hi) no, the seqs are different
@mp-ym9gw 2 жыл бұрын
nice
@AntonAnru 2 жыл бұрын
Thanks
@jiaquinnzenxin9900 4 жыл бұрын
I'd love to hear the crave VCO going to the TD-3 audio in for use as a sub oscillator.
@khanhgomsu 3 жыл бұрын
Hi! Does anyone know if I can synchronize this TD-3 with Yamaha arranger keyboard PSR-S (770, 970, 775, 975,...)? I want to play styles on Yamaha keyboard and add bass lines from this TD-3. Can TD-3 follow the rhythm and chord progression? Any help is appreciated
@AntonAnru 3 жыл бұрын
Tb3 can be synced to whatever via midi or cv, its sequences can be transposed, or you can just send notes via midi to it from external sequencer or daw
@pokerdealer2003 3 жыл бұрын
I would love to hear this with roles reversed, the crave can produce amazing bass, good stuff keep it up!
@creator79 2 жыл бұрын
Anton, regarding this "multiple bug", I assume it is caused by incompatible voltages of the TD-3's gate (0 to +12 V) and the multiple in / out (-5 to +5 V). However the hold, reset and play/pause switch at more than 3.2 V. So when it's directly connected it seems to work because the hold, reset and play/pause inputs simply get voltages +/- the 3.2 V threshold. But when the multiple in-out path is used, which is also built for - 5 to +5 V, there seems to be a problem - which I cannot describe in detail, because of missing knowledge about the Crave's internals or the electronic backgrounds. I think the multiple out tries to stay conform to its specifications +/- 5 V and it cannot handle the 12 V in this range and hence possibly never clearly reaches the 3.2 V threshold, even though 0 V means off and 12 V on. The multiple seems to buffer. Does anybody else have an explanation?
@AntonAnru 2 жыл бұрын
Good point
@StamatisStabos 5 ай бұрын
Hi Anton, can you use the Crave with td3 mo as a pad to play basic long notes when you change patterns on td3?
@jaspertermors 3 жыл бұрын
Great, informative video. The Crave has some interesting inputs compared to the Neutron, mostly because the built-in sequencer / arp. Very versatile machines.
@AntonAnru 3 жыл бұрын
Yes, for me crave is also more interesting in terms of connectivity than neutron.
@Magnus_Loov Жыл бұрын
Wow! I'm blown away by this! For me the CV out/in And CV Gate have always been totally uninteresting since "I already have Midi". I didn't expect/think about that you could do this, only thought about the regular "key down", "note" (like recording just notes with midi). I don't own a Crave YET! But I do own a couple of other Synths that I can do these kind of tricks with. But Crave seems to especially be interesting with all its patch points (and what can be done to/with the sequencer on it) and all the extras stuff like "multiple", "mix", "assign" etc. And that the resonance can be modulated (unusual and good). But then again should I REALLY get another Synth device(would be the 10th) ? Why the crave for it?😄
@AntonAnru Жыл бұрын
Welcome to cv and gates
@adventureswithsteve2981 3 жыл бұрын
Great video , now I want a Crave too , which do you think is best to get first , Currently I have uAcid8 , hapiNES, Pocket Operator Tonic , Sub and Robot , I also got a MicroFreak and a Circuit plus an SQ-1
@AntonAnru 3 жыл бұрын
Thank you Steven. I think I'm asked quite frequently about what to choose, crave or td3, so I've decided to make a video to mention all points. I guess I will release it in a week
@adventureswithsteve2981 3 жыл бұрын
Anton Anru I was too impatient and after hearing the dreamy patches for td3 I ordered this first, so I have a blue version coming tomorrow
@michaelmarsmusic 3 жыл бұрын
Does the Crave Have Cv //Gate IN? So you can control it with an older synth via CV Out? I know the crave has Midi In // Cv Out. How About CV Pitch // Gate In?
@AntonAnru 3 жыл бұрын
Yes, there's a patchbay with lots of cv ins and outs
@seanpopple5984 Жыл бұрын
Hi Anton, great videos. Looking fkr some help please - I have my crave and td 3 synced with Korg Volcas (volcas are the master). As far as I can tell they are all on different channels BUT how do I stop the TD3 being triggered when I hit play on the Crave?
@classyB916 10 ай бұрын
I think you change the trigger input
@eclectic-cinema 7 ай бұрын
Hey Anton, that's great stuff. Thanks for sharing. I have a question. If I hear correctly, in about 13:55 you are sending slides (glided notes) from TD3 to Crave... And Crave receives them and plays them. Am I correct? I would like my modular microsynths receive slide notes.... If I would use TD3 as a sequencer, and send the CV Out to OSC CV In of anoter modular/semi-modular synth will it play the slides programed in TD3?
@MHFC-bp6zg 2 жыл бұрын
Hi antun I’m using crave and td3 usually with ableton. Every time that I’m writing my pattern and play them in the arrangement it triggered the patterns inside the synthesisers and than I have to press ‘stop’ in both of them. If you understand what I mean, can you tell me how I fix it? Thank you
@AntonAnru 2 жыл бұрын
When you hit play in Ableton it sends Start message to then via midi/usb. I don't think there's an easy and obvious way to turn it off. Maybe it's possible to pass then through some midi filter, where it's possible to switch off Start/Stop message. But I can't help with it at the moment. I never did it
@juancharry1457 4 жыл бұрын
Hi ! Nice video ! Can you sync the tempo of both machines using cs or sync in-out?
@AntonAnru 4 жыл бұрын
You may send clock from Crave Assign output (seq clock) to td3 sync in
@distortimus7631 3 жыл бұрын
I have a problem syncing the td3 to Ableton. The tempo is always changing and it frustrates me.
@sonofdirt 3 жыл бұрын
try using an audio clip with a click & patch that to the Sync In.. then you will be synchronized @ audio rate instead of MIDI which I assume is your issue with tempo drift. I use a similar technique to sync my MC-202 to DAW.
@BPEMETO Ай бұрын
Thank you very much for the video! : ) I really want to get started with Behringer synths. What would you recommend for me to get first? The Crave or TD-3 ?
@AntonAnru 20 күн бұрын
crave - it's much more interesting
@BPEMETO 20 күн бұрын
@@AntonAnru Thanks! : )
@jasonfields1947 4 жыл бұрын
SUPER video, thanks ... Newbie question time ... I am using a TB-03 (midi slave) & TR-8s (midi master) (no computer /DAW)... I am getting a Crave this week, can i use the CV patch output from TB-03 to Crave (as shown here W/ TD3 to Crave) and not need to use midi from TB-03 to Crave ? If i am understanding correctly, the TB-03 would control the tempo & start/stop without midi or UCB via the (CV) patch cable ? THANKS in advance for any advice . Jason from Detroit
@AntonAnru 4 жыл бұрын
Hi Jason, thank you for the comment. Td3 doesn't have tempo/clock output, so it can't control other devices tempo via cv. The easiest way is to use midi. And make sure to set Crave tempo input source to midi in synthtool app
@jasonfields1947 4 жыл бұрын
@@AntonAnru Thanks, i don"t have a computer that supports downloading drivers (chrome not windows) so synthtool will not be an option for me. Will i need to buy a laptop with windows and downlaod synthtool to sync my crave ? I truly hope i can use my crave in sync with out a laptop. My 3 machines (TB-03 /TR-8s &Crave) in a daisy chain. thanks for your time . If you have any tips on a no laptop set up please share.
@AntonAnru 4 жыл бұрын
i guess these settings can be done on the front panel. But for me it was much easier to use the app. There is also a ios app, if you don't have a computer
@AntonAnru 4 жыл бұрын
Hello again) you may sync crave to td3 using cv if you send clock from Crave Assign output (seq clock) to td3 sync in
@F50 4 жыл бұрын
Can the CV be controlled via USB at all? My DAW recently added some CV stuff but I don't have any CV hardware or a CV soundcard or anything, just wondering if Crave would be a good intro to it, or whether I'd need to keep splashing out...
@AntonAnru 4 жыл бұрын
you can't control CV just by connecting Crave via USB. yes, as you mentioned, you need a special sound card, or any module that converts USB/MIDI to CV
@unclemick-synths 3 жыл бұрын
David, the Korg SQ-1 has a non-sequence mode where it is a USB-MIDI to CV converter. It worked fine for sending CV to my Neutron from my MPC.
@rexcellencemagee6729 4 ай бұрын
I’m going to have to watch your videos we share the same instruments.
@mixx-mastersinternat.djservice 3 жыл бұрын
is the same sequence programmed on the Crave or is it just a blank pattern ? i only need a slave which gives a little more grovve like the gate functions. my td3 is the slave to mc707 via midi, i only want to send the td3 pattern to crave, what are the settings in the synth tool for td3 and crave ?? thank you
@AntonAnru 3 жыл бұрын
Crave has its own sequence here, td3 as well. You may send notes from td3 to crave with cv and gate outs on td3.
@mixx-mastersinternat.djservice 3 жыл бұрын
@@AntonAnru cool . i am new in this modular synth world, my first step.. where do i put cv and gate outs from td3, in wchich slot from crave ?? p.s. i have bought your td-3 dreamy sequences and the other too, i will listen to them soon.. thanks..
@AntonAnru 3 жыл бұрын
Thank you for support. Td3 cv out - crave osc cv in, td3 gate out - crave env gate in
@yodavongohta7577 2 жыл бұрын
So, I am connecting the TD-3 cv and gate out to the crave and it plays the correct melody but it's an octave too high, while the frequency knob of the crave is in its middle position. Could I change the octave on the crave when using the external control?
@AntonAnru 2 жыл бұрын
I guess you may transpose as usual with the keys
@yodavongohta7577 2 жыл бұрын
@@AntonAnru thanks I just found out how this works.
@UFO-303 3 ай бұрын
Is it possible to implement Square pwm on TD-3 via cv input? Using external lfo?
@AntonAnru 3 ай бұрын
td-3 doesn't have PWM cv input
@rchrd3353 4 жыл бұрын
i have and love the td-3.. was thinking of trading it in for a crave .. any reason i shouldn't ?
@AntonAnru 4 жыл бұрын
For me crave is more interesting. But td3 gives THAT sound. It's hard to choose
@KonisAdonis 3 жыл бұрын
Why trading? They're both supercheap.
@rchrd3353 3 жыл бұрын
@@KonisAdonis more so desk space and simplicity. ended up going for the crave and while i do like it more, i do miss the immediate acid goodness of the td-3 on rare occasions. the random button was great fun. i plan on picking one up again when the cool new colors are available and more or less just keeping it as decoration on the side and only reaching for it when i need THAT sound or randomly generated patterns to tweak.
@DennisdeWeerd 4 жыл бұрын
My crave also 'holds' to a single step when connection the TD-3 -> multiple IN, multiple OUT -> hold (Crave). A bug, maybe?
@AntonAnru 4 жыл бұрын
i guess the voltage is shifted a bit
@madvalrocketinsky4292 4 жыл бұрын
Same...
@unclemick-synths 3 жыл бұрын
My suggestion is to use a mult lead or one of those star mults.
@patrickschulz6162 2 жыл бұрын
I don't know if this can be the cause of the multiple bug, but it could kzfaq.info/get/bejne/h9J1Y8uGqcC8d4E.html
@PrivatMann Жыл бұрын
Can I actually break the Synth if I patch it with itself? Or patch „wrong“ with other synth? I got an td3-mo and I got no idea what to do 13 „holes“ on the front 😅 where to put cable
@AntonAnru Жыл бұрын
It's hardly possible to do any harm.
@LoveLove-us2qz 3 жыл бұрын
Thank you very much for the explaination! I have a question.Maybe you can answer me. I have the behringer rd6 and td3 can I use the Behringer cave with both and do i need a computer? Or can I put the 3 mashines togethet. I am thinking of getting a cave.
@AntonAnru 3 жыл бұрын
Yes, you may sync them all via midi. So you'll get a nice setup in sum
@LoveLove-us2qz 3 жыл бұрын
@@AntonAnru thank you so much for answering back. I will get one. Stay safe and I take a kindly bow. Keep up your Videos!
@marcoagius6926 Жыл бұрын
can you save patches on the crave like the td3 does? thanks
@AntonAnru Жыл бұрын
Not patches, but patterns - yes
@marcoagius6926 Жыл бұрын
@@AntonAnru okay thanks for your reply
@tubeMonger 3 жыл бұрын
Can you use the oscillator of td-3 with the crave?
@AntonAnru 3 жыл бұрын
So you mean pitch control from td3?
@tubeMonger 3 жыл бұрын
@@AntonAnru I'm a bit confused with the patching. Behringer has a video where they use a module that adds an oscillator to Crave. Here's the video: kzfaq.info/get/bejne/j5h1gM1hrquZmXU.html
@AntonAnru 3 жыл бұрын
Yes, you can add anything to a modular system. You were asking about using oscillator, yes, you can. But it depends on how you gonna to use it
@tubeMonger 3 жыл бұрын
@@AntonAnru I need to try some patches and come back with an answer to the "how" :-) - thanks for your responses!
@AntonAnru 3 жыл бұрын
Welcome
@gw33b 9 ай бұрын
Hi, is it possible to connect multiple behringer devices to a computer via USB?
@AntonAnru 9 ай бұрын
Yes
@theesfarich9513 Жыл бұрын
Great work! You know what you're doing. But what, if you don't have a DAW in background and want to couple the two devices directly? I have both of them for days know, but can't succeed. Volcas are easy in that. Took me 5 Minutes. It's a shame, Behringer has no real manual or documentation... Regards, Thees
@classyB916 10 ай бұрын
Does it work if you just use the sync jack? Or did you find another solution?
@0713dm 3 жыл бұрын
How about Crave + Roland TB-03? 🤔
@AntonAnru 3 жыл бұрын
I'm thinking of it...
@KosmoDeuz 4 жыл бұрын
Тоха, скажи как настроить чтобы crave арпеджио играло в external clock?
@AntonAnru 4 жыл бұрын
Нужно настроить выход AssignOut, чтобы он клок выдавал. Можно через приложение или с передней панели
@ph911 3 жыл бұрын
Спасибо. Не все понятно, но прикольно)
@AntonAnru 3 жыл бұрын
должна же оставаться интрига)
@ph911 3 жыл бұрын
@@AntonAnru можно тебе вопросов по комутации написать?) Перехожу на железо и местами туплю. Затыки по схеме и подключению. В вк или в телеге например..
@AntonAnru 3 жыл бұрын
Да, можно в вк
@ph911 3 жыл бұрын
@@AntonAnru написал. Спс.
@SLEEP-236 3 жыл бұрын
Should I purchase a 2nd crave or a TD-3? There’s not a lot of difference in money. Answers on a postcard please👍
@AntonAnru 3 жыл бұрын
2nd crave is a good choice as you can combine then into a bigger modular synth
@SLEEP-236 3 жыл бұрын
Anton Anru it’s the sensible thing to do based on price and flexibility. And they sound so good. It was my first synth and has really got me hooked.
@MediaMusik777 4 жыл бұрын
love the td3 sound! crave ....no 1/4 out big mistake imo
@AntonAnru 4 жыл бұрын
It's sad, but no a big deal to my taste
@MG53v8 2 жыл бұрын
There's a hidden menu 3 , might be able to fix the hold problem there. But you've probably figured it out after 2 years since posting ^^)
@AntonAnru 2 жыл бұрын
Yes, thank you
@user-sx2iw2hq3l 4 жыл бұрын
Шикарное видео, если бы сделать дубль для нашего Могучего было бы супер. Спасибо.
@AntonAnru 4 жыл бұрын
Сложно по времени на несколько фронтов. Поэтому на английском, больше охват, и думаю большинство россиян меня понимают с моим акцентом
@daviddeyons 2 жыл бұрын
How long is your TS cables ?? 1,5 feet??
@AntonAnru 2 жыл бұрын
i've got many of them, from 10 cm to 150 cm
@aaaper5522 4 жыл бұрын
im having a really hard time connecting my crave to ableton. arp and sequences just dont play. i have midi track and sync on input and track out output. i just cant figure it out!!! any tips?
@AntonAnru 4 жыл бұрын
Check out buffet size in preferences. It should be as low as possible. Also turn on reduced latency in options menu
@BackgammonFun 10 ай бұрын
Здравствуйте, помогите начинающему. Я подключаю rd6 к td3 для клока sync out - sync in, а можно таким же образом с td3 продолжить на crave?
@AntonAnru 10 ай бұрын
Здравствуйте. Я уже не помню точно. Но должно получиться. Нужно настроить вход tempo in на прием клока и можно синхронизировать
@BackgammonFun 10 ай бұрын
@@AntonAnru Просто при подключении к tempo ничего не происходит. Единственная реакция на start/stop, но оно просто туда сюда клацает.
@AntonAnru 10 ай бұрын
@gotti3847 настройки темпо входа смотрели?
@user-cg5in2gt4y 3 жыл бұрын
А есть ли инструкция на русском где-то? Кто нашёл подскажите плз.
@AntonAnru 3 жыл бұрын
Это не совсем инструкция, это уже фишки и идеи. На русском нет
@andyjohnson9714 3 ай бұрын
Но как ты аудио рутиш в запись? Аналоговые выходы в аналоговый миксер/пульт и потом его мастер аут в саунд карту? Или как?
@AntonAnru 3 ай бұрын
просто сразу в карту, без микшера
@alekseykorma7211 3 жыл бұрын
Привет я купил себе крейв а он не работает что делать
@dharmov 2 жыл бұрын
Учить английский
@klaasj7808 4 жыл бұрын
so 300 euro vs 3000 with original 303 and mother32
@AntonAnru 4 жыл бұрын
I would take their latest tb03, so the overall price will be under 1000
@BarbieChaite 4 жыл бұрын
4:50 I don't hear such a difference
@AntonAnru 4 жыл бұрын
Maybe it's not too obvious and it also depends on timbres and seqs on both synths, but even here you may notice that some additional ratchets are added due to hold
@e.d.2126 3 жыл бұрын
акцент как у Мутко )
@AntonAnru 3 жыл бұрын
Вместе учились
@synthsproblems3475 3 жыл бұрын
Interesting video But i think this 2 dont sound good at all together . crave is very much louder than the td3
@alex883pnhaev2 4 ай бұрын
По акценту слышу что наш!
@AntonAnru 4 ай бұрын
наш🖖
@knightofcupsnavi 3 жыл бұрын
Печальное зрелище.
@AntonAnru 3 жыл бұрын
Спасибо за комментарий
@knightofcupsnavi 3 жыл бұрын
@@AntonAnru , да как то не за что. Сожалею, на самом деле. Пытаетесь освоить богатую англоязычную аудиторию?
@AntonAnru 3 жыл бұрын
@@knightofcupsnavi богатая она или нет, вопрос второй. а то что это по сути весь мир, вот главная цель
@knightofcupsnavi 3 жыл бұрын
@@AntonAnru, китайцев, примерно, 1.5 млрд. Есть огромная аудитория в латиноговорящих странах - испанский, португальский бразильский, итальянский языки. Выбор, несомненно, за Вами, однако смешение всех в один англоговорящий котёл я считаю неосмотрительным.
@AntonAnru 3 жыл бұрын
С китайцами да, но не из-за языка, а из-за блокировки интернета. Остальные уже могут смотреть на английском. В России тоже смотрят на английском
@poipoilo579 4 жыл бұрын
Почему нельзя было на русском..?
@AntonAnru 4 жыл бұрын
Самый популярный вопрос)
@dwit1080p Жыл бұрын
Русский? Советский
ОВР Шоу
Рет қаралды 8 МЛН
Captain Pikant
Рет қаралды 181 М.
Anton Anru
Рет қаралды 32 М.