Bicycle hub sealed bearing upgrade for under $1 plus parts

Рет қаралды 6,960

10 ай бұрын

In this video I attempt to upgrade an alloy Shimano Mountain Bike hub to a sealed bearing for under $1, without using a lathe or any fancy tools except for a drill (or an impact driver) and a 3D printer... if you don't own or have access to a 3D printer you could always make the tool out of wood if you are a bit handy.
When I was a teenager I did some awesome modifications to bicycles, but long are the days where I could go into a hardware store or bike shop and just buy a bearing race, these days its individual ball bearings of many different sizes. Now, sealed bearings are something I can get behind.
The hollow axle and bearing I used in the video: s.click.aliexpress.com/e/_Dk7...
Also available longer solid shaft versions: s.click.aliexpress.com/e/_Des...
And the 60002RS (rubber seal) or 6000ZZ (metal seal) 10x26x8mm bearings: s.click.aliexpress.com/e/_DlQ...
Digital calipers I really need to invest in: s.click.aliexpress.com/e/_DC2...
Tinkercad link to the 3D printer file referenced in the video:
www.tinkercad.com/things/kqir...
Music: Hotham - Find
• Hotham - Find
Please help the channel grow! Like, comment & subscribe!
Follow me on social media or if you like you can help support my future videos via Buy Me A Coffee or PayPal: linktr.ee/Fix_Tech_Stuff
eMail: fixtechstuff@gmail.com

Пікірлер: 29

@FixTechStuff 9 ай бұрын

Note: The bearings I used are 60002RS 10x26x8, so its 26mm, not the 25mm I mentioned in the video, we can thank the inaccuracy of my steel rule. I verified this by checking from zero, and then again at the 10cm mark. Fortunately it all turned out just fine with my 24.5mm design which came out of the printer a fraction over 25mm anyway. I need to do my eyes a favour and invest in some digital calipers like these: s.click.aliexpress.com/e/_DC2wp4r

@patrickbodine1300 9 ай бұрын

Link not working.

@FixTechStuff 9 ай бұрын

Strange, it works on my end, even in a private window. It's a digital caliper.@@patrickbodine1300

@peterxyz3541 Ай бұрын

Use wide washer to evenly torque in the bearing

@pramudithad Ай бұрын

thanks for sharing

@1OTDM 22 күн бұрын

The Bike Sauce built a pretty simple little bearing press which seems easy enough to use to do this. The video was called "Replace Sealed Cartridge Hub Bearings" or something similar.

@SaintThomas2009 Ай бұрын

Sweet upgrade! I bet the wheel rolls super smooth!

@FixTechStuff Ай бұрын

It does indeed. After finding the bike shop didn’t even stock bicycle bearing races (they only had balls), I think, if possible I would change everything over in future. So much easier to work with and replace too.

@garrethtinsley2435 9 ай бұрын

I have an ancient (80s/90s bicycle) with a busted old type (non-sealed-cassette) BB. However attempting to stuff a new sealed bb in the shell I learned eventually that the shell is tapped for an Italian threaded BB/end cups so I've probably buggered the aluminium threads. The whole thing has been so much more of a nightmare than the last one I did, many many many tools for this mongrel/money pit of a bike, square wrench flats, hammer, washer, whole toolkits, working all night until I had to leave for work attempting to beat train strikes etc. FML, the things in pieces as I can't find the correct threaded cassette BB anywhere to put it back together. All in all your video made me happy just bcos it shows I'm not the only one having to get extreme to fix these b*sterd bicycles. I'm thinking my next step is to rebuild the existing BB as I have new bb's and races ( I hope they will fit the old spindle!) Or to buy a stripped shell BB that has external bearings iirc! Thanks anyway!

@FixTechStuff 9 ай бұрын

It's good to know we are not alone! With your nightmarish situation, it might be worth checking out your local recycling centre / tip shop for other bikes or parts. I often mix and match bits and pieces to get results. I've collected enough that I've passed up on some really nice bikes because they were barely much of an upgrade from what I've already built. On my wifes 24" bicycle I swapped out the 6 speed ratchet type hub for a newer shimano hub with 8 speed cassette from a spare 26" rim I had lying around. A bit of fiddling about getting it to run true, but really rewarding experience, upgrading something for less than $5 or $10.

@garrethtinsley2435 9 ай бұрын

@@FixTechStuff tempting, but I don't think my partner would approve if i brought more bikes home haha. BTW, do you think ADHD gives us extra perseverance through hyperfocus? It's a blessing AND a curse to me!

@jenickjohnson4361 6 ай бұрын

Can you please suggest me a method to fix a bearing if the bearing seating required few millimetres material more?

@FixTechStuff 6 ай бұрын

You're saying the bearing hole is too big for the bearing? perhaps a different size of bearing is available, I'm not sure

@jenickjohnson4361 6 ай бұрын

@@FixTechStuff the problem is with the axle. I am thinking to fix it by rolling some paper or plastic material around the axle.

@FixTechStuff 4 ай бұрын

Aluminium can as a shim might be a good option, other than that buying an axle from aliexpress.@@jenickjohnson4361

@jenickjohnson4361 4 ай бұрын

@@FixTechStuff I tried that but when I try to stuff it, it deforms. I have to try it again.

@paulogracaribeiro2931 3 ай бұрын

wich filament did you use??? not a 100% sure on the plastic stuff better turning some wood or some rubber!!!

@FixTechStuff 3 ай бұрын

I use PETG, PLA will also work, it doesn’t get hot enough to matter. If you had a lathe obviously wood would be better.

@pauloribeiro1627 3 ай бұрын

If you use a hole saw and cut the wood at the right dimension.

@FixTechStuff 3 ай бұрын

that might work too@@pauloribeiro1627

@willjenkins2842 9 ай бұрын

grease that puppy up! =)

@FixTechStuff 9 ай бұрын

Yeah for sure, the grease in those bearings looks like vaseline and we can do better than that.

@lorinomaga2386 5 ай бұрын

Saan ka bumili ng spacer ng axle ng hub?

@FixTechStuff 4 ай бұрын

Not sure exactly what you mean, but the links to the axle and bearings I ordered are in the description.

@benbrewdog Ай бұрын

This a fake video 1 my A do you know how much a 3d printer would coast just to to do this?

@FixTechStuff Ай бұрын

In the description I wrote: "if you don't own or have access to a 3D printer you could always make the tool out of wood if you are a bit handy." You could get a piece of broom handle, drill a hole and sand it to size with a drill or something. See if your local library or some other organisation has a 3D printer. My $149 3D printer has more than paid itself off with all of the useful things I've repaired or made, so it was money well spent.

@peterxyz3541 Ай бұрын

The 3d printer does cost (at least $99 new, with promotion price at microcenter); but, missing the point of this vid: Less money = more brain Or the internet meme: Girl’s voice: “How are you so good in so many things” Guy’s voice, sound of frustration, sound of exhaustion, a bit of prideful flex: “when you’re poor, you learn how to do many things” Or…the point of this vid: Outthink your problems. If I done have a 3d printer (I don’t), I would use a drill attachment (cheap at harborfreight) for sanding. What if it’s the wrong size? Another opportunity for you..me to flex and either roll up extra tape or sand paper to size or spin the attachment against sand paper to reduce the size. “How are you so good with so many things”. “Poverty, baby! Either grow or starve😂”

@dieterjosef 2 күн бұрын

You don't know what you are doing. When you press in a bearing with force you press on the outer ring. Otherwise you can destroy it what you have possibly done with the force you applied with the threaded rod. Use bigger washers or wire for staying on the outer ring.

@FixTechStuff 23 сағат бұрын

You should really pay attention when commenting and try not to be so rude. If you watched the video I said "you can't go about putting force on the centre part of bearings, that's just asking for trouble". I had no large washers on hand, either way that would not have helped at all. You can't force bearings into an aluminium hub when they will not fit. The hub needed to be machined, which I did without a lathe. The bearings fitted perfectly with no force required.