Thanks!

Gary be like myeah I'm just giving these a clean with some WD-40 and a wire brush

Thanks for always specifically stating what you’re using to clean parts (detergent, WD40, etc). So many restore videos just say “clean” without details it’s frustrating. Learning a lot 🙏

algorithm dumped this on me, im sure glad it did. You have great taste for aesthetics.

The great thing about that paint job is that you can just use some black paint or a Sharpie on any chips or scratches. It'll match with the other black splashes.

That's hilarious ! That's a bike seller close to Munich here in germany and still exist ! That bike has come a long way mate ! To the rear hub situation , sorry this washer suppose to be there for sure because it is part of the rubber seal but what is a common mistake that people use the wrong tool ! Yeah sounds stupid but it is that way , there are two tools one is the casette remover tool (old style screw on ) and one to remove the lockring and the one for the old style casette is just a bit smaller bro. In the end I have to admit that those type of casettes were always a bit tricky to remove but there is a tool from shimano that has a center pin for this situation ! Have fun mate !

Handlebars look good. Black forks and spacers are a great touch.

truing the wheel with a piece of tape is G.

👏👏👏this was a blast,great looking ride! Look forward to more,thanx to Toasty for putting me on to you!

0:24 *I thought my eyes saw it wrong* That is a small Village based Bikedealer located near Munich Bavaria. More or less in the Middle of Cropfields. Zorneding is the nearest City, Wolfesing is only a few Houses in size. I googled it again and it was really the Last House . We drove past that shop alot when i was a small boy/Teenager.

It's was my first new bougth MTB,in begin of the 90s in Germany❤

Crazy how a bike end up on the other side of the world, would love to know its story. We have quite a lot of wheeler bikes over here in Germany, going to pick up a 6600 hybrid on Monday. BTW I'd recommend chain lube for the freehub there's a second race with bearings on the inside, if you can't do a rebuild it's probably best to really flood it with lube.

Bike looks great the bars are super neat. Hairspray works well for grips, dries sticky and helps hold grips still.

0:24 it is now called Fahrrad Hemrich and is near to Munich, Germany🙂Nice combination of parts and frame again, the colourmatching is pretty cool😎You got it shine again⭐️⭐️⭐️Cheers, mate👋🏻

I like how you keep it right hand rear brake and left hand front even though you're from Australia

Watching these vids fills me with joy. Thanks a lot 👍🤩

i'm at 0:01 and I know is going to be a great build.

Love your work Gary but was struggling to see the leather in the seat post refurbishment section. Then....I realised you were referring to the lever.

Love the shape of that Mothbar!!! 😍

prolly one of my favorite build from your channel, kudos to you Gary! 🍻

lovely colours!

Awsome project Gary always love watching your videos and it was great that you and toasty could meet up keep pedaling 🤘🔥👍

Man I love these cockpit combo’s

The sticker on the Bike is a Bikeshop near Munich, located in southern Germany! Crazy how far these Bikes travel in their lifetime!

thanks Gary for another great bike rescue, Summer Cruiser sorted, great stuff!

Another banger! Love it

Sharp looking bike Gary as usual😊😊😊

Good stuff Gary

this one's skits!! recently started a build of my own after getting keen as watching you and toasty show us how it's done. so far been loving it, plenty to learn and super rewarding seeing it come together. keep up the awesome content Gary!! :)

love the details ! -the splatter paint job -the contrast black fork with the black seatpost -the overall balance of mostly black parts with hints of silver parts dotted in -and those bars look so comfy side note video idea : you ever thought about doing a “rate/review my followers bikes” video ?

Rear end noise is beneficial.....The geared bikes hear you coming and they scatter accordingly

I already know this is going to be sick 1 min in💥

I have the freehub disassembly tool and its not that expensive. Just needed some filing though for the notches as they werent super precise to fit fully into the lockring part. $5 five years ago however it came on the slow boat from overseas and took a month. I use Phil's tenacious oil for the bearings however heard that 90w gear oil or chainsaw bar oil will work. Both are quite cheaper and you get 3-4x more thans Phil's and i will try either or when i run out.

For the heasset screw you can mout the stem above the steering tube and that will guide the starnut straight through

Wowowowowzie! But some things did get better with age, I do not want any kind of integrated dropout on an aluminum frame

You make old pushies look so fresh and this build is so clean and sharp, very Gary 👍

Nice looking bike that

the build is so rad!! love it ... fthe sticker at 00:27 : Im living twenty mins away from the bikeshop where its from :)

Love your work Gary, can you give a tip on where to find a generic fork like this?

Sick!!

Gary my dude. Is that a M900 XTR seatpost clamp I see 👀 Send it my way plz 😅

Nice cruiser/mtb/single-speed build! 😎👍 I got that same raceface bash guard! with matching chainguide on my old school dh bike. 😁 Btw, how many bike you got? Just curious... Hahaha... Btw, keep up these nice bike builds, and keep chucking parts on your builds! 😎👍🚴

A.B.B. !! Another Bitchin' Build ....with attention to detail nice job again Gary !

Gary 🅿️ is a ⛽️

This one is sweet. Do you still have the drill press? It might have helped with the seat clamp. I'm still working on converting my 1986 Miyata to 1x9, but it's slow-going. I was going to do a 2x, but it was getting too complicated. The problem I'm having now is that I had downtube shifters, but the non-standard mount for them, and trying to find the conversion to cable stops for it is impossible. I have to make something, but I don't really have the skills for that. Probably have to go with a clamp-on style.

why so clean everytime bruh..

sick build, very helpful to me - your shifters are in the canti position rather than the v-brake position, i got the same shifters, you wont have linear pull rn btw though

New video = coffee with Gary

That Shimano seat clamp looks a good match to the old Shimano 600?/Ultegra? QR skewers. I call them 🐰 ears. Chanel No.5 rims: So chic!

That came up a treat Gary luv ya work, is there a Melbourne store that sells the Mothbars or is it acase of ordering them from the website?

rad bike rad builder

🔥

🎉

Sick build! Sticker is german btw :)))

f'ckin awesome man. You can eat muff on those handlebar

where did you get the forks? thanks

How many turbos does this man have??? 😂

tidy!

what's the polish stuff at 2:39? can't quite make it out

When you say single speed chain is it a 1/8"?

Is wheeler a high-end bike brand?

I still dont fully understand the point of a tensioner on a single speed. if the chain is tight shouldnt you not need one? I have no experience and am just curious.

Easier way to install the star nut is to put an extra long bolt through an old stem cap and use the stem cap as a guide

whats the song yo?

klunker in danish is testicles

If they front wheel isn't broken don't fix it I say.

German Bike Shop*

these forks look slack man. For a bike of this age

klunker.....ppl keep misapplying that term

Gary, that's an ugly build