Can-Am Ryker how to properly change your oil

No video

Can-Am Ryker how to properly change your oil

Рет қаралды 20,913

Күн бұрын

#canam #ryker #BLUEDRAGON
70% OF MY VIEWERS ARE NOT SUBSCRIBED TO MY CHANNEL. PLEASE CONSIDER HITTING THE SUBSCRIBE BUTTON. THANK YOU.
If you have any questions about motorcycle tuning You can reach out to us through the BLR TUNING Facebook page.
/ blrtuning
In this video I show you step-by-step how to change your oil properly on a Can-Am Ryker. the steps can be followed for all models the 600 the 900 and rally.
click on this link and I will show you step-by-step how to check your oil properly.
• Can-Am Ryker How to ch...
These are the steps you need to take when you are checking your oil level on the Can-Am Ryker this applies to all models.
1: take the vehicle for a 9 Mile ride. this will ensure that all the oil is distributed throughout the motor and that it is at running temperature. just letting it idle until it's at running temperature will not achieve this.
2: open the air vent and have a paper towel handy before you shut the bike off.
3: shut the vehicle off you now have 10 seconds.
4: within 10 seconds you need to remove the dipstick wipe it off once and put it back in. make sure you thread it all the way down and then unthread it again and look where the oil level is.
5: that is officially your oil level if it's in the middle there is no need to add oil or take away oil.
6: a motor that is overfilled with oil can do more damage quicker than in motor that has low oil.
RYKER OIL CHANGE KIT ON AMAZON.
900 ACE AND RALLY MODELS ALL YEARS,,,
www.amazon.com...
600 MODEL ALL YEARS,,
www.amazon.com...
The ramps that I use are the rhino 12k ramps. there are stackable and very compact for storage.
you can find them on Amazon but they are usually sold out so here is the link to Amazon. they should only cost you around $50 you can also purchase them in person at O'Reilly's for about $5 more than Amazon.
Yes they are you can purchase them on Amazon..
www.amazon.com...
I have a complete playlist of videos all about the Can-Am Ryker that you can check out on my KZfaq channel by clicking the following link.
• Can-Am ryker
Please don't forget,, While you are here visiting my KZfaq channel to hit the subscribe button. If you quit on the little bell icon you will get notified next time I upload a video.
Follow me here.
Twitter
/ billramseyerjr
Instagram
@BIGGDADDY007BR / biggdaddy007br
snapchat
@BIGGDADDY007BR
KZfaq
m.kzfaq.info...
Xbox-1
HONDA250XATV

Пікірлер: 73

@RykerRydes 4 жыл бұрын

Nice job. If I remember correctly the 600 does take less oil than the 900's. They sell a separate kit for the 600.

@jaytek4 3 жыл бұрын

Just wanted to give a shout out and thank you for your video. I always try to learn how to do basic maint (oil, breaks, etc) and you made this very easy for someone who has only worked on cars. As an idea for a future video, I know the can-am dealers talk about their yearly inspections (which includes the oil change), if you could put something together that shows what fittings needs to be greased (if any) an other steps that would be great! I believe most of it is a visual inspection but I haven't heard the same story twice when talking to shops.

@BLRTUNING 3 жыл бұрын

That's a great idea and I will look into this further thank you have a great day I'm glad I could help you

@East_TX_LCR 3 жыл бұрын

Whelp, did my first service at 6k. Video was helpful.

@tpv59 2 жыл бұрын

PERFECT. THANK YOU. 10/10. I learnt a LOT. Thank You.

@telescope2067 3 жыл бұрын

You did a really good job on your Ryker.

@BLRTUNING 3 жыл бұрын

Thank you

@tat2joecool 2 жыл бұрын

Just finished up my first oil change. Great video Bill!

@BLRTUNING 2 жыл бұрын

Thanks

@ryker4124 Жыл бұрын

Manual says the 600 gets 2.64 qts with filter, 900 gets 2.96 qts with filter.

@leeyong414 4 жыл бұрын

Thanks for the post, great info for my Ryker maintenance.

@FlyboythaACE 10 ай бұрын

Thanks bro this was super helpful!

@leonardnigro9820 2 жыл бұрын

I appreciate your good informative videos.

@BLRTUNING 2 жыл бұрын

Thanks for subscribing to the channel I really appreciate the support

@b0nghit Жыл бұрын

Great dyi vid man. Thank you so much!

@markpage5567 4 жыл бұрын

Nice video Bill. I'll be changing my oil this year for my Rallys first change and your video was very informative. Have you ever tried the Invisible Glove cream? I don't know about you but I hate wearing gloves to work on vehicles...not enough finger sensitivity or the gloves get caught on edges and tear. The invisible glov e cream goes on wet and then dries in a few minutes. It creates a film on your skin that you just wash off after work is done. I've been using it for years and love it. Looks like There is now a similar product called Ghost Glove that does the same.

@BLRTUNING 3 жыл бұрын

I've never used it before I will have to check it out thank you

@williamlodato5058 4 жыл бұрын

Great video!

@deidredorsey1326 4 жыл бұрын

Very nice and clean job. I was also worried about that great watch getting damaged.

@saimon1409 2 жыл бұрын

Hi, what are the diameters of the two washers under the drain plugs, please? Thank you :-)

@goodvibezrydez2814 3 жыл бұрын

Bruh ... I need that LED Bull Bar when I get my Ryker in a few months

@tomtardif4387 3 жыл бұрын

Looks like they gave you an extra package of O-rings and Crush washers it's a bonus...lol

@GrillPiece63 4 жыл бұрын

In my 600CC kit, I only got one set of the o-rings.

@alfredlee2668 28 күн бұрын

Dear bill were can i get new o rings when i change gear box oil .Thanks

@BLRTUNING 17 күн бұрын

If you can find the size of those o-rings or take an old one out and take it with you to a hardware store they can probably just match it up. They are not anything special. Although if you ask BRP they will probably tell you different.

@jodymorrison9495 3 жыл бұрын

You didn't show where you put the jack to jack the back up so you could put the stand where it is. Where did you put the jack at?

@BLRTUNING 3 жыл бұрын

The floor jack towards the back end of the bike is sitting exactly where I lifted the bike up from. Sorry I guess I should have shown that in the video for some reason I thought it was in there. anyways if you fast forward the video to exactly 9:01 in this video. you will see that the jack is under the rear swing arm with a rag on it so it doesn't scratch it up.. it is safe to lift the bike from the swing arm the frame or the rear shock mounting location.. Thank you for stopping by my KZfaq channel I really hope you'll consider taking the time to hit the subscribe button. That always helps me out tremendously and it's what keeps me making KZfaq videos this 33 minute video that you are watching took me 3 hours to film and about another 3 hours of video editing... I hope you have a wonderful day if there's anything else I can help with please feel free to message me. you can always reach out to me through the blr tuning Facebook page.. m.facebook.com/BLRTUNING/

@1112dejon 3 жыл бұрын

what is the FT/LBS for the secondary drain plug? and what is the FT/LBS for oil filter cap bolts? thanks

@BLRTUNING 3 жыл бұрын

I believe I go over this in the video. if you can't find the torque specs you can get a hold of me through social media like Facebook messenger. I contact information is in the description below the video. Or you can reach out to me through my Facebook page. BLR TUNING m.facebook.com/BLRTUNING/ I would be more than happy to send you a screenshot from the actual maintenance book.

@KrazyCow02 4 жыл бұрын

Can you add a link to where you bought the oil kit from, please. Thanks!

@BLRTUNING 3 жыл бұрын

I got mine from a local motorcycle shop here in town. If you go on Amazon's website and just search XPS ryker oil kit you'll see the correct kit on there there is a kit that is separate for the six hundred... The 900 and the rally take the same one.. I don't know why I am just now seeing your message I do apologize. KZfaq is not very good at sending notifications. I literally just now seen this message..

@LtColPenguin 2 жыл бұрын

Hey Bill! Great video. Any tips on changing the gearbox oil?

@BLRTUNING 2 жыл бұрын

I have not had to do it yet but when I do I will be making a video on it

@amorio78 4 жыл бұрын

how do you measure the amount of pressure to apply on your torque wrench? for example 80 lbs of torque...pls help i don’t about wrenches and i’m planning to do the oil change myself too.

@Gaspedaleks 4 жыл бұрын

The torque wrench is adjustable, usually by rotating the handle you can set the desired torque (there may be different variants, but all torque wrenches Ive used have been like that). And then it will make a click sound once you apply the set torque.

@BLRTUNING 4 жыл бұрын

sorry I didn't reply right away KZfaq is not sending notifications for some weird reason some comments on my videos are just now getting to me... As the person stated the answer the question for me yes torque wrench is adjustable usually by twisting the handle to the desired torque specifications then it will usually have a little lock down at the bottom that you will twist tight to lock it into place you'll hear a clicking sound or if it's an electronic torque wrench you will hear a beeping when it has reached torque as you're turning the bolt..

@RobertTorres1981 4 жыл бұрын

Did post the link for the ramps?

@BLRTUNING 4 жыл бұрын

hey sorry about that I was trying to find them elsewhere than Amazon because right now Amazon is sold out but you can buy them from a third-party seller on Amazon however they look like they're expensive from the third party seller probably because ever since I posted them they've been sold out everywhere.. I posted them about a month ago sitting next to my Can-Am Ryker and a photo of my Can-Am Ryker up on them and literally like a thousand people bought a set of those ramps.. I purchased mine from O'Reilly's for $5 more than what Amazon charges.. They are the rhino 12K ramps and they are stackable and easy to store.. I have updated the description below the video so there is a link now to Amazon they should have some back in stock in a couple weeks www.amazon.com/RhinoGear-11909-RhinoRamps-Vehicle-Capacity/dp/B006EGAIII/ref=mp_s_a_1_11?dchild=1&keywords=rhino+ramps+12000&qid=1592502382&sr=8-11

@gamalierbravo8536 3 жыл бұрын

How many quarts does the 600 takes??

@BLRTUNING Жыл бұрын

I believe around 2.6 but you'll need to look in your owner's man

@jamescantu7726 3 жыл бұрын

How hard is it to do the coolant. I damaged my radiator and have one on order. I didn't see a drain plug on the radiator.

@BLRTUNING 3 жыл бұрын

It's not fun I can tell you that.. you can pull one of the hoses off but be prepared for a mess... Also I do offer the radiator protective grill for the Can-Am ryker I ship those anywhere in the US and my friends over treal performance carry my product and ship it anywhere outside the US.. KZfaq is very bad about sending notifications to the actual person that owns the KZfaq channel. I am literally just now seeing your message and it says it's 5 months old. I greatly apologize for this... If you would like to reach out to me in order a radiator protective Grill to protect your investment please feel free to reach out to me through the blr tuning Facebook page.. m.facebook.com/BLRTUNING/

@tuannguyen-pt6qs 3 жыл бұрын

Hi bill I plane to buy can am ryker but I don't have garage can I park outside.if can am water proof?ty

@BLRTUNING 3 жыл бұрын

Yes you can park the bike outside it's not going to hurt anything if it gets wet

@giovannam925 4 жыл бұрын

Are those the Rhino ramps? Thanks for this video. 👍🏾

@BLRTUNING 4 жыл бұрын

Yes they are you can purchase them on Amazon.. they should be right around $50 they're usually sold out on Amazon because there are very popular product.. you can also purchase them at O'Reilly's.. www.amazon.com/RhinoGear-11909-RhinoRamps-Vehicle-Capacity/dp/B006EGAIII/ref=mp_s_a_1_11?dchild=1&keywords=rhino+ramps+12000&qid=1592502382&sr=8-11

@BLRTUNING 4 жыл бұрын

@giovannam925 4 жыл бұрын

BiLL Ramseyer thanks looks like Walmart sells them out by me as well

@187Apollo 2 жыл бұрын

How many miles until you change it again?

@BLRTUNING 2 жыл бұрын

Change your oil every 6,000 miles

@187Apollo 2 жыл бұрын

@@BLRTUNING awesome! thanks Bill!

@TheBlackboy504 9 ай бұрын

Can I reach out to you for help? I’m trying to ask a question.

@BLRTUNING 9 ай бұрын

Send an email And we can exchange contact information. blrtuning.tech@gmail.com

@TheBlackboy504 9 ай бұрын

Okay

@jhillestad 3 жыл бұрын

Where did you jack the bike up in the back to allow the jackstand to be placed where it is ?

@BLRTUNING 2 жыл бұрын

Under the swing arm

@ryanmorgan2475 2 жыл бұрын

Didn’t heat the bike up will it be a problem

@BLRTUNING 2 жыл бұрын

It won't be a problem it's just that oil drains quicker when it's warm. When oil is cold it gets thick like honey. When it's warm it gets thin and runs a lot better. Basically when it's warm you'll get more oil out of the motor then if it was cold. But no worries just let it sit there and drain for a little bit longer

@wolfeman6310 3 жыл бұрын

very nice video Bill.. Question I was going to buy a 1500 lbs ATV/Motorcycle from Harbor Freight. Would that work to change the oil?

@BLRTUNING 3 жыл бұрын

As long as you can get it up in the air it will be easier to change the oil but you can do it from on the ground it just doesn't have a lot of ground clearance underneath of it so it is definitely much easier to get it level and up in the air

@RobertTorres1981 4 жыл бұрын

Mine only came with one set of O-rings

@BLRTUNING 4 жыл бұрын

That's what other people are saying as well so I guess I got a bonus

@williamperez5537 4 жыл бұрын

Where did you get that funnel from?

@BLRTUNING 4 жыл бұрын

O'Reilly's

@GrillPiece63 4 жыл бұрын

Bill, did your oil filter receptacle had any oil in it during the change? It was the case for me.

@GrillPiece63 4 жыл бұрын

But mine had a least half of the receptacle.

@BLRTUNING 4 жыл бұрын

@@GrillPiece63 it would not be uncommon to see oil sitting in there.. as you drain the oil out of the bike that will slowly as well.. that's why I say pull the drain plugs off and then open that because in some cases it can be completely full and totally make a mess of oil going everywhere as soon as you open the seal.. if I'm understanding you correctly you're talking about both spot where the oil filter sits and you have to undo the three bolts to open the top ..

@BLRTUNING 4 жыл бұрын

@@GrillPiece63 Yes mine had oil in there as well but it drained out as I drain the oil out of the motor. I let it sit with the drain bolts out for 10 minutes..