BMW E46 M3 Shifter Bushing Upgrade DIY (2001-2006 BMW M3)

Рет қаралды 27,183

Күн бұрын

►Within the linkage that connects the shifter inside the car to the gears inside the transmission, there are a series of bushings keeping everything in the right place. You'll need to replace those shift bushings with enough use, as they'll have gone loose and sloppy. Replacing the shifter bushings should make the 6-speed manual a much more enjoyable transmission as the shifts become tight and precise.
Watch along as Gareth Foley, FCP Euro's BMW Wizard, tackles a shift bushing replacement in a BMW E46 M3.
00:00 - Intro
01:41 - Tools Needed
02:45 - Job Start/BMW E46 M3 Reinforcement Plate Removal
03:13 - BMW E46 M3 Exhaust Removal
04:43 - BMW E46 M3 Driveshaft Removal
06:56 - BMW E46 M3 Selector Rod Pivot Removal
08:38 - BMW E46 M3 Shift Lever Arm Removal
09:50 - BMW E46 M3 Shift Lever Removal
10:13 - BMW E46 M3 Shift Knob Swap
13:02 - BMW E46 M3 Shift Lever Arm Bushings Swap
15:07 - BMW E46 M3 Shift Lever Install
15:38 - BMW E46 M3 Selector Rod Pivot Install
16:49 - BMW E46 M3 Shift Lever Arm Install
18:00 - BMW E46 M3 Selector Rod Install
19:26 - BMW E46 M3 Driveshaft Install
22:10 - BMW E46 M3 Exhaust Install
24:50 - BMW E46 M3 Reinforcement Plate Install
25:14 - Wrap-Up
Buy BMW E46 M3 Powershift Bushing Here: www.fcpeuro.com/products/bmw-...
Buy BMW E46 M3 Selector Rod Here: www.fcpeuro.com/products/bmw-...
www.fcpeuro.com/products/bmw-...
1997-2000 BMW 528i Sedan
1997 BMW 528i Shift Lever Bushing
1998 BMW 528i Shift Lever Bushing
1999 BMW 528i Shift Lever Bushing
2000 BMW 528i Shift Lever Bushing
1999-2000 BMW 323i Sedan
1999 BMW 323i Shift Lever Bushing
2000 BMW 323i Shift Lever Bushing
2000 BMW 328Ci Coupe
2000 BMW 328Ci Shift Lever Bushing
2000 BMW 328i Sedan
2000 BMW 328i Shift Lever Bushing
2000-2006 BMW M5
2000 BMW M5 Shift Lever Bushing
2001-2003 BMW M5 Shift Lever Bushing
2006-2010 BMW M5 Shift Lever Bushing
2001-2006 BMW 330Ci Coupe
2001-2006 BMW 330Ci Shift Lever Bushing
2001-2006 BMW 330i Sedan
2001-2006 BMW 330i Shift Lever Bushing
2001-2006 BMW 330xi Sedan
2001-2006 BMW 330xi Shift Lever Bushing
2001-2007 BMW 525i Sedan
2001-2007 BMW 525i Shift Lever Bushing
2001-2007 BMW 530i Sedan
2001-2007 BMW 530i Shift Lever Bushing
2001-2003 BMW 540i Sedan
2001-2003 BMW 540i Shift Lever Bushing
2002-2006 BMW 325Ci Coupe
2002-2006 BMW 325Ci Shift Lever Bushing
2002-2006 BMW 325i Sedan
2002-2006 BMW 325i Shift Lever Bushing
2002-2006 BMW 325xi Sedan
2002-2006 BMW 325xi Shift Lever Bushing
2004-2005 BMW 545i
2004-2005 BMW 545i Shift Lever Bushing
2006-2010 BMW 550i
2006-2010 BMW 550i Shift Lever Bushing
2007-2018 BMW 328i Sedan
2007-2018 BMW 328i Shift Lever Bushing
2012-2015 BMW 328i 3.0L L6 Shift Lever Bushing
2012-2018 BMW 328i Shift Lever Bushing
2007-2018 BMW 335i Sedan
2007-2018 BMW 335i Shift Lever Bushing
2012-2015 BMW 335i 3.0L L6 Shift Lever Bushing
2012-2018 BMW 335i Shift Lever Bushing
2008-2018 BMW 535i Sedan
2008-2018 BMW 535i Shift Lever Bushing
2008-2013 BMW 128i
2008-2013 BMW 128i Shift Lever Bushing
2008-2013 BMW 135i
2008-2013 BMW 135i Shift Lever Bushing
2009-2011 BMW 335d
2009-2011 BMW 335d Manual Shift Lever Bushing
2009-2016 BMW 528i Sedan
2009-2016 BMW 528i Manual Shift Lever Bushing
2011 BMW 1 Series M
2011 BMW 1 Series M Manual Shift Lever Bushing
2012-2016 BMW 528i xDrive Sedan
2012-2016 BMW 528i xDrive Manual Shift Lever Bushing
2013-2016 BMW 320i Sedan
2013-2016 BMW 320i Manual Shift Lever Bushing
2013-2016 BMW 320i xDrive Sedan
2013-2016 BMW 320i xDrive Manual Shift Lever Bushing
2014-2018 BMW 328d Sedan
2014-2018 BMW 328d Manual Shift Lever Bushing
2014-2018 BMW 328d xDrive Sedan
2014-2018 BMW 328d xDrive Manual Shift Lever Bushing
2014-2016 BMW 535d
2014-2016 BMW 535d Manual Shift Lever Bushing
2016-2018 BMW 340i Sedan
2016-2018 BMW 340i Manual Shift Lever Bushing
2016-2018 BMW 340i xDrive Sedan
2016-2018 BMW 340i xDrive Manual Shift Lever Bushing
2016-2018 BMW 330e
2016-2018 BMW 330e Manual Shift Lever Bushing
2017-2018 BMW 320i Sedan
2017-2018 BMW 320i Manual Shift Lever Bushing
2017-2018 BMW 320i xDrive Sedan
2017-2018 BMW 320i xDrive Manual Shift Lever Bushing
2017-2018 BMW 330i Sedan
2017-2018 BMW 330i Manual Shift Lever Bushing
SUBSCRIBE: kzfaq.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

Пікірлер: 29

@jonathanalastra5752 5 ай бұрын

I recommend anyone who is deciding to do this on jackstands in your garage. Go through the extra effort to remove the exhaust and driveshaft. Trust me it’s definitely the way to go. I did it without removing and looking back definitely should’ve removed it and saved so much time and effort compared to taking it out.

@legambaz Жыл бұрын

Enjoyed clip. What a big job for a shifter. I wonder how often this part needs maintenance. Unbelievable how many chassis braces BMW uses in their cars

@newtypecs700 Жыл бұрын

you guys are best👍

@alexderkach_ 3 ай бұрын

7:02 - 7:20 important observation. Will try doing it without removing the drive shaft 👍

@moStallion 2 ай бұрын

So is the shifter on my 550i the same as the 545

@MegaBusted101 Жыл бұрын

what is wrong with the website, i cant place my order. I have been trying to do that for few days now but no luck. I sent a e-mail but all the solution given to me did not help. the issue after the website was under maintenance few days ago

@lovepreetsinghhanjra1997 Жыл бұрын

👍👍👍

@hoomandavodi8981 Жыл бұрын

Great video. I have a 2006 m3, 1st & 2nd gear get stuck and won’t move when in higher rpm, but with low speed and low rpm can change them just fine. Downshifting is no problem. Any thoughts?? Thanks again for the great contents 🙏🏻✌️

@mettaworldelbow7104 Жыл бұрын

Late but had the same issue with it being shiftable at low RPM, locked out at high RPM. In my case it was a sheared pivot pin that was leaving the clutch release arm dangling / misaligned. In turn it also destroyed my throw out bearing. Did the clutch and flywheel while in there as well, and there's a BMW stainless steel replacement for the pivot pin to remove the silly failure point of a plastic pin that requires dropping the transmission.

@FailofWar127 2 ай бұрын

@@mettaworldelbow7104 were you just locked out at high rpms or would it also grind slightly? I think i may have a very similar issue

@mettaworldelbow7104 2 ай бұрын

@@FailofWar127 If I remember correctly initially it would just lock out, but it got worse with time and eventually it would lockout + grind if I attempted to shift at high RPM. Was basically forced to crawl around shifting below 3k

@matthewnicholas6365 Жыл бұрын

I did most of this on my garage floor on axel stands. I stopped at the Bush that mounts onto the gearbox as couldn't drop the brace down (i assumed it needed a jack under it, which I didn't have) Not a nice job on your back, not at all. My exhaust is now making horrible noises because I think it's touching the chassis brace. Need to adjust that and check it isn't also blowing 😢

@fcpeuro Жыл бұрын

Nice work doing this on your back, Matthew! Sometimes you need to go back and finetune these things 😢

@matthewnicholas6365 Жыл бұрын

@fcpeuro I used to enjoy getting under a car but now I'm in my 40s it takes it out of me. I slid over gravels and nuts from time to time. I took my shirt off and it looked like I'd been savaged by someone or something 🤣

@JohnnyCorleone Жыл бұрын

Do you guys have a video doing this for an e36 m3?

@valdeabeast3283 Жыл бұрын

I was putting this back together and when I connected the shifter with the shift selector rod I noticed that inside the car after installing it my shifter know wasn't centered it was up and to the right when it was in neutral and I have no clue why or how to fix it fo you know what the issue is thanks

@tari9553 10 ай бұрын

did you ever find a fix to this? my shifter currently sits so far forward I can't shift into 1st, 3rd, or 5th gear. Any help is appreciated.

@user-vw9ur1bi6k 7 ай бұрын

@@tari9553i think u have installed the shifter rod 180 deg away..the shifter rod is bend..and need to be facing backwards..he has said it during removal of the shifter rod

@AnthonnyAndria Жыл бұрын

dude the extra load you put on the engine mounts is huge by not supporting that gearbox

@5abivt 9 ай бұрын

Dude, the engine mounts see 300 lb-ft of torque of twisting motion with the heat from an exhaust and running engine and cooling system. Hanging about 60-75% of a 115 lb transmission isn’t hurting anything

@AnthonnyAndria 9 ай бұрын

@@5abivt go do calculate the total load due to engine weight versus the gearbox overhanging and then come back defend your point of view

@gardenofnightmare 3 ай бұрын

Could I use 3D printed bushings for this? Would they wear out too quickly?

@DanielEhlmann 3 ай бұрын

They would definitely wear too easily. You’d have to use some exotic filaments (meaning a $$$$ printer)

@heinekencorona8151 6 ай бұрын

just finished rebuilding my shifter, it was a cunt of a job, solo, on jack stands, laying on my back. I didnt remove my driveshaft though. Learned a lot and the shifter feels better now. anyone has similar experience.

@jonathanalastra5752 5 ай бұрын

About to do it tomorrow

@jonathanalastra5752 5 ай бұрын

Hey I have a question, how did you get the pin off that holds the shifter above the transmission, he’ll of a job man

@heinekencorona8151 5 ай бұрын

@@jonathanalastra5752picking tools and a lot of frustration.( time stamp the part in the video you're referring to. )