WATCH THIS IF YOU OWN A MANUAL BMW

Рет қаралды 73,472

3 жыл бұрын

You should upgrade your clutch pivot pin if you own a BMW with a manual or SMG transmission. I have linked Brass and Steel upgraded pins down below. I also discuss the 5th gear lean on the ZF 5 speed manual transmission on this BMW E53 X5 3.0 with a factory ZF manual transmission. #bmw #bmwmanual
DIY For Shift Pin/Detents:
• BMW ZF 5 Speed Manual ...
Clutch Pivot Pin:
ECS Brass: click.linksynergy.com/link?id...
Genuine Steel:
Genuine BMW Clutch Fork Pivot Pin - Priced Each: Pin that is located on the bottom half of clutch fork for BMW
URO Brass:
amzn.to/3nXojyX
Transmission Shift Pin Repair Kit:
Genuine BMW Transmission Shift Pin Repair Kit: Fix your sticking Shift lever for BMW
Support my channel by becoming a member using this link: / @shoplifetv
My Amazon Store: www.amazon.com/shop/shoplifetv
Buy My Merchandise: www.shoplifetv.com
Ask me a question: www.shoplifetv.com
Request a Shop Appointment: www.shoplifetv.com
Instagram: @ShopLifeTV
/ shoplifetv
My vlog channel: / shoplifevlogs
KZfaq Business Inquires: Email me amotorwerks@gmail.com
Disclaimer: Some links will contain affiliate links. Due to factors beyond the control of ShopLifeTV, I cannot guarantee against improper use or unauthorized modifications of this information. ShopLifeTV assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ShopLifeTV recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ShopLifeTV, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ShopLifeTV.

Пікірлер: 197

@Dmxravin Жыл бұрын

The Pivot pin is not just plastic but it's nylon. Nylon is very hard wearing and self lubricating. No one talk about the fact that the pivot pin lasted for 20 years?

@berniewharton6535 3 жыл бұрын

Glad to see you folks are back.

@bobafittness1346 3 жыл бұрын

Glad to see you back. Keep coming the E46 content going!

@cleotusclump1007 3 жыл бұрын

I'm learning more every time I view your channel, keep up the good content. E46 4 Life! Be safe.

@dizzy83 3 жыл бұрын

It's crazy how I was looking this up on Friday about the pivot pin and he made a video about it

@M_Dennis87 3 жыл бұрын

Thank you so much for tackling this. I have a 2001 M roadster that will be going under the knife this winter. This is one of the projects I want to address.

@romero_mellow9573 3 жыл бұрын

As a BMW technician myself I must say I really enjoy and learn from your videos. Keep it up!

@cruzpartida3758 3 жыл бұрын

What’s it like working for BMW?

@BazvdB 3 жыл бұрын

I’ve learned a lot from your videos but I think it’s time you build a nice big workbench and take your professionalism to the next level. Good luck!

@Steve-gn4hk 3 жыл бұрын

Yo missed your videos. Glad you’re back at it.

@Stomper 3 жыл бұрын

Welcome Back! Good video as always!

@albertj2459 3 жыл бұрын

Glad to see you posting BMW content a again. Great info!

@ShopLifeTV 3 жыл бұрын

Haha have a lot more BMW and non-BMW content coming soon! Thanks man!

@jason83685 3 жыл бұрын

Bmws Manual are the most of pleasure to drive! nice to see you again.

@ShopLifeTV 3 жыл бұрын

Couldn't agree more! Hope you are doing well!

@wilfredocaraballo4846 3 жыл бұрын

Thanks man im about to have my clutch change soon. This video really helped out

@ShopLifeTV 3 жыл бұрын

Anytime man! Good luck with the service!

@gustavopavlini480 3 жыл бұрын

Man great content. Very helpfull and explained very well. Many things i learnt and will learn from you videos. Thank you for your hard work. Apprecuate it a lot. Have a good day.

@MrCuckoobox 3 жыл бұрын

Hey, Jason, Always enjoy your informative vids and you make everything look so easy. You are a motivator. Glad you are back in NC.....Wish you were in the RDU area........Just did a Tbelt on a M20 in my E30.

@ShopLifeTV 3 жыл бұрын

Hey! I hope you are doing well and I really appreciate the support and kind words! I am glad to be back in NC, I'm sure ill be visiting RDU area sooner or later. Hope my videos continue to help!

@AndrewRamirezOlvera 3 жыл бұрын

Thank you for the information! Good thing I haven’t done the manual swap for my 330i zhp yet

@phallock73 Жыл бұрын

Thanks!

@jamesrobinson1579 3 жыл бұрын

A good video. Thanks. I am shocked and dismayed though, that you didn't address removal of the awful shift delay valve! I have had 5 BMWs in a row (e39, e30, two e36s and an e83... after discovering the delay valve on the e39 about 2 decades ago, the very first thing I always do is drive up on a ramp, remove the stupid thing and bleed the clutch back hard. (in the M3 and X3 I still have, I also replaced the rubber clutch line with stainless braided just for good measure. Your clutch will last twice as long at least (because you aren't always slipping it like a granny shift EVERY time you let the pedal out) It definitely doesn't make it difficult to shift! I recently put a stage 3 clutch and UUC evo3 in the M3 and it is still slick and smooth. This is a deletion EVERY BMW manual owner should do. It takes minutes and only requires a couple of wrenches. Zero dollars for a huge improvement in shifting.

@lmc333 Жыл бұрын

Excellent and clear explanation! Superbe video bro. Thank you.

@worldsails2000 3 жыл бұрын

I replaced the shift pins in my wife's '02 M Coupe due to the 5th gear lean. It was not as hard as I thought it would be. I've never removed a transmission before and it was much easier than I thought it would be. I bought the tool kit used off eBay then turned around and sold it for more money than I bought it for. I wasn't too happy that the shop who replaced the clutch didn't recommend this as the clutch was replaced just a year before. While I was in there I replaced the clutch pivot pin with a brass one like in your video.

@ShopLifeTV 3 жыл бұрын

Many shops run on production and would rather replace the big issues only and have faster turnaround. Sometimes these shift pins/detents can cause more of a headache when replacing and shops would lose money since they wouldn't be able to quote the job correctly.

@Codeman785 3 жыл бұрын

Dude, I just found you and I can't thank you enough for videos like this. We need more nitty gritty part swap videos like this, they are rare.

@Nico_335i_DCT 3 жыл бұрын

Very nice tips brother and sister. Dutch regards, Nico.

@FilmsByZapata 3 жыл бұрын

It’s been a cool minute 💯👌🏽 good to see you back on here Jason. Hope everything is well 🙏🏽

@ShopLifeTV 3 жыл бұрын

It sure has, nice to see you in my comments again! My pinned comment explains! Hope all is going well for you too!

@y2ksierra 3 жыл бұрын

Great video! 👍

@ShopLifeTV 3 жыл бұрын

Thank You!

@markii72 3 жыл бұрын

I used to own a Z3 with a 5-speed manual made by GETRAG, and it also showed the 5th gear lean. Sometimes when shifting into 5th, the spring of that gate got stuck and it would not center the shifter when taking it out of 5th. It also showed some signs of stubborn shifting with cold outside temperatures, so I drained the old transmission oil while hot and replaced it with Pennzoil Synchromesh (made for GM GETRAG transmissions). It shifted like butter hot and cold afterwards, and the leaning 5th gear problem was completely(!) fixed. That was a cheap fix and money well spent!

@ShopLifeTV 3 жыл бұрын

The fluid definitely helps the situation! Fluid should be changed every 30-40k miles regardless. Thanks for sharing your experience!

@tommytenzo 3 жыл бұрын

I’m having a similar issue. There’s almost no tension on the shifter going towards 5th gear. And it’s hard to go into reverse

@Astra8676 3 жыл бұрын

Hey dude, glad to see you!!!!

@ShopLifeTV 3 жыл бұрын

Hey man! It has been a minute lol My pinned comment explains! Hope all is well!

@Astra8676 3 жыл бұрын

@@ShopLifeTV yup... All is well, was just wondering where you were, with all the stuff that's going on in the world !!

@andreslopez9318 2 жыл бұрын

Great vid i have a 5sp manual e36 and 5 gear pops out unless i hold it in place. No grinding noise or clunks

@ninetyonemfive 3 жыл бұрын

I appreciate all the info...I have a 91 M5 that might need a trans rebuilt. I was told there's a loose bearing inside. I'm getting a second opinion soon

@goldenratio183 3 жыл бұрын

new video lets go!

@winnabegobob1547 3 жыл бұрын

I miss watching your videos

@brendam455 3 жыл бұрын

omg you solved my 5 gear lean when i get off the freeway i aways skip a gear bec its stuck in 5 lean

@N.P.DETAILINGUK 3 жыл бұрын

Hey bro glad to see the shop going well! How much are those shift pins?

@edward9862 2 жыл бұрын

I just got done bolting the transmission back into the engine block. Maybe next time. 🎉😂

@michaelmarcus509 3 жыл бұрын

Own a manual 528it touring, and a engine trans swapped 318ti with the ZF and both have 5th lean thanks so much! Also 328i e36 came with ZF if that helps anyone!

@jacobacheson4702 3 жыл бұрын

Hey shoplifetv! Love the vids

@ShopLifeTV 3 жыл бұрын

Thank you Jacob! Hope all is well!

@jacobacheson4702 3 жыл бұрын

Thank you! You too! I just want to say your vids have helped me so much. I’ve learned how to swap all my interior and did a manual swap just from your videos. Your channel is the best!

@ShopLifeTV 3 жыл бұрын

Glad that my videos have helped and hope they continue to do so. It's always a great feeling when you DIY! Keep on DIYing!

@shootmkillerxd8101 3 жыл бұрын

Hey Jason can you please make a video on swapping ms45 to ms43 for newer e46s for tuning. Thanks!

@bobross6677 3 жыл бұрын

Well now i have more advice for the e36 i wanna buy

@Testa11 Жыл бұрын

The other day I saw a x5 manual I was like wtf lol

@brookef1540 3 жыл бұрын

Your videos have been my go-to for keeping up with my E46 M3 maintenance for years now, so thank you for the quality info! I'm not having any luck with my current issue though- my M3 is a 6spd manual (about 120K miles), and suddenly it is hard to engage the shifter into 1st and 2nd gear. The shifter feels like it's not lining up with the gears right... I was able to force it into the gears to get home. From what I've read, it could be as simple as rebuild kit, to a not-so-simple transmission issue. Any advice? Thanks again for your informative and helpful vids!

@louiseitner916 9 ай бұрын

Hey man. Did you manage to solve your problem? If so, what turned out to be the cause? I have the same problem @brookef1540

@fredcaroline7600 3 жыл бұрын

How to replace input and output shaft bearing on Getrag 240 5 speed. I also can't find a reverse gate on Getrag240 5 speed. Thanks

@madoushi1634 3 жыл бұрын

Thanks for the video, I've watched all your videos, I have a 6 gears manuelle 320d, all shift gears are good except the 2nd which don't pass smoothly but requires more force, could you tell me what possible causes are making this problem?

@JohnFaire 3 жыл бұрын

Another "while your there" moment, is the rear main seal. What are the chances of messing that up? I know bmw sells the housing for it with the seal in place so there isn't a chance of pressing it in too deep. But, what about the oil pan gasket area. If sliding a new surface to be sealed on, like the real seal housing, wouldn't that be a big potential problem for new leaks if not careful. How could we be sure, after doing the work, we will not acquire a new leak at area where the real seal housing meets the oil pan gasket? Also, put in the discription a Link to the pins for the reverse and 5th gear gates, as well as the other pins you mentioned.

@hkgs1 3 жыл бұрын

Hey , this is great info, thank you , I have E46 M3 Manual, recently we replaced Clutch, Flywheel (both LUK) and a brass clutch pivot , however there is a play and noise coming out of Transmission to Propshaft which is very annoying , any ideas why it would be ?

@31acruz 3 жыл бұрын

Hi, question for you. I am replacing the shifter bushings on my 2000 BMW Z3, instructions call for "slightly dropping" the transmission a little to get access to the top clip. My question is, once I disconnect the gibo isn't the transmission still connected to the engine? a solid item, the transmission will not move "a little" as it is still bolted to the engine right? and if it does it will put stress on the engine. Or will the engine mounts give a little to allow for the "little drop"? thanks.

@myfire9554 3 жыл бұрын

Love your videos. Very descriptive and informative. You do need to invest in some better camerawork though.

@MrTarcira 3 жыл бұрын

Long time bro

@francom9692 3 жыл бұрын

I own a 2006 e87 when I set off the gearbox judders but not always do I need to replace the clutch

@tdwcamar095 3 жыл бұрын

I have a manual 02 330ci couple and I’ve noticed from 1st to 2nd gear I get shutters/vibration from around my driveshaft. Don’t really know if it’s trans or driveshaft related. Could it be giubo related? 190k miles. Not sure what bushing have been replaced around that area.

@leoneltovar5157 3 жыл бұрын

Hi your videos are great. I just wanted to know if you do swaps auto to manual on a 04 325 ci sulev .

@alexpeters9992 3 жыл бұрын

A worn out pivot ring; Is that why when I press the clutch in the noises stop coming from the transmission? Also good info on that 5th gear lean. I could never figure out what was wrong.

@saganworshipper6062 3 жыл бұрын

I have the ZF 6spd in my E90 328xi, are there any specific weak points on that transmission? I have 90k on my original clutch so at some point these will be things I need to consider. Thanks as always!

@TheMrbumpersticker 3 жыл бұрын

I’ve actually heard of a lot of negatives regarding the brass pivot pin in the way it wears faster or just as fast as the plastic one. The stainless replacement seems to be the best option.

@Chicitypo 3 жыл бұрын

Yup, I’ve read the same thing. Many say it’s worse than the plastic ones.

@AliAmer-ij2cs 3 жыл бұрын

How to control the movement of the hand gear for BMW x5 2002

@josephphelps6913 3 жыл бұрын

Will this pin cracking in the transmission problem cause my transmission to slip into neutral when I stomp the gas?

@adamcamberos5634 3 жыл бұрын

bmw has start off assist inactive and a drive moderately light what can thr problem be someone help seems like some is wrong with traction what can it be cant figure it out if I step on gas it will take off then slow down ...

@fazrulrusdi3709 7 ай бұрын

The refresh kit for zf is it can be use for getrag as well..both are 5speed

@littlevwalters 3 жыл бұрын

I love all your video. Can you help me? I'm trying to change the Headlight housing for the 2004 BMW 330 ci. it a task that I'm not succeeding

@goldcoastrob984 3 жыл бұрын

Hi from Australia my 2001 x5 3.0i manual and was having trouble with the shift being sloppy there no feeling in the gear change any ideas or a fix

@tycharles241 3 жыл бұрын

Hey can you tell me if the E46 and E90 transmission bell housing bolt pattern the same?

@milossteelm3 3 жыл бұрын

@ShopLifeTV I have a Manual 2002 BMW e46 M3 and I rarely(accidentally) while in 1st Gear let go of the Clutch Pedal while the Car is Running and the Car kinda lunges forward from the Rear and you can hear it creak. Is this damaging anything, and if so what parts should be checked/replaced? TY

@in54ne82 2 жыл бұрын

I hope my brass pivot pin lasts me a while because I've seen them get worn out pretty quick. Stainless steel is the way to go from what I've seen.

@borisp9499 3 жыл бұрын

I have a question in regards to the spring on the e46 M3 SMG transmission. You said that if that spring breaks the transmission won't shift. Can you explain why this spring breaking causes trouble in shifting. I know that it is the same transmission (and same spring) for the manual version of this car and I've never heard of that happening to the transmission. This spring clicks in the little roller into front (1, 3, 5) or rear (2, 4,6) gates, so I don't know why if it breaks how would it stop the transmission from shifting.

@donspinaczo 3 жыл бұрын

I have a manual E91, it is very heavy to put first gear when engine is cold. Oil changed twice, didn't help. Do you have any experience with that?

@neversaywho7753 3 жыл бұрын

Hey bro, I've got a bmw e36 325tds and I'm trying to manual canvert it, would you be able to give me some tips and a list of parts needing to do this please, thanks

@victoranguiano7401 3 жыл бұрын

Looking to get my 04 E46 tuned can you recommend a shop in LA or Orange county

@gerardogoveche8064 3 жыл бұрын

Hey men i have this question...im doing a Manual swap on my e46 328i the transmission is a zf from a e36 what i need to make it fit any help would be appreciated

@shami2613 2 жыл бұрын

Hi mate in x3 manual 2008 car jolts while accelerating feels more on the left front wheel.

@Dominicane1 2 жыл бұрын

I have the same year and model 2001 BMW X5 3.0 with a 5 speed. I just picked it up and noticed it is slightly jerky when shifting into 2nd gear. Any ideas or tricks of what it can be?

@whiskeyonetwoactual1116 2 жыл бұрын

How much is the going price for an E46 manual refresh to include the $20 part you mention?

@mms16mms16 3 жыл бұрын

Damn... Just yesterday I reinstalled the transmission in my 165k mile 530xi (had the original factory clutch) and left the original stock pin in. One day later I watch this video... doh! It was not cracked, but now I’m worried.

@zosimajoe1012 Жыл бұрын

Thanks for the video but I have question plz, my car is BMW e87 116i ( P018481) i checked which clutch i need on BMW with OEM 21 20 7 576 519 so I found 2 clutches, diameter 230mm and 228mm , is that makrs a difference?? So please im waiting for your answer

@alext91 8 ай бұрын

Alexis Hi guys I have a 05 530i and I found a manual from a 06 335i it’s this transmission would work for my e60 and wat else I’m going to need Thank you very much guys for your support and kindness may the LORD BLESS YOU TALK SOON

@MrClarck100 3 жыл бұрын

Do all BMW S5-31 gearboxes have the same bolt pattern? I just bought an e46 320D with a 5 speed (S5D-280Z) and was wondering if it would fit a M50/52/54.

@josephbambara7426 Жыл бұрын

Thanks for the information, washing you on the e 46 platform, got me into the e 46. I own a 2000 323i, manual. For the past 4 days, I been having some issues in my e 46, shifting is harder, and when I press the clutch, I hear a knock sound coming from the real, then today I hear a winding sound . Can you please tell me what you think could be the issue. Thank you very much

@TheSchoolCircle0311 Жыл бұрын

does the 5th gear pin/ detent repair (kit) also apply to the 6speed 330xi transmission?

@Leeholtom2911 3 жыл бұрын

Hi is this part on the E46 M3 manual gearbox?

@basithph8958 3 жыл бұрын

A BMW with a manual transmission would be a nice car to own

@ShopLifeTV 3 жыл бұрын

Any BMW can be converted to a manual with the right amount of money lol! But you are right all manual BMWs are a blast to drive!

@AliAmer-ij2cs 3 жыл бұрын

How to adjust the skewer gear for me BMW x5 2002

@hbel71 2 жыл бұрын

If I need Crank the engine bay hand the car manual transmission need to do something in transmission or go ahead and carank it?

@breakrebuildrepeat5321 3 жыл бұрын

Just purchased a 2008 335i E92 manual with 150k doing maintenance on the brakes and suspension now before getting into the powertrain. My idea is to make 450hp no more then 500hp nothing crazy, probably going with pure turbos pure600. Any clutches you recommend?

@juancoliorangel9419 Жыл бұрын

I don't know if I would have to buy another transmission or do the job myself changing all the pressure springs. I would really appreciate it

@MichaelAMangone 3 жыл бұрын

I couldn't find rebuild parts or a kit for my ZF S6-37BZ. Any suggestions? The gates are still positive, but I'd like to put another 100K miles on it.

@mohitnawketand9087 3 жыл бұрын

Hi can I bypass a leaking oil cooler in a 2008 320i oil is mixing with coolant

@itsjustcarguy 3 жыл бұрын

Hm, I wanna rebuild mine , any tips?

@AlmazaHookahLoungeTempe 3 жыл бұрын

Can you let me know why my BMW 530 I pops out of the gear second and fourth when you push and let go of the gas pedal

@jessieszygenda1587 Жыл бұрын

Can you please send show me the location of the CTC solenoid on 2003 530i bmw auto transmission

@vassamoylov9902 3 жыл бұрын

Say no to the brass clutch pivot pin. The brass deforms rather quickly so either go with the stainless steel version from bmw or the plastic one.

@juancoliorangel9419 Жыл бұрын

Good afternoon, I have a BMW 325i 2001 manual trasmission, 2.5 motor, and all the speeds fit fine. Only the 4th speed scrapes to enter. Do you think the problem is the pressure spring, or how can I locate it? Could you help me? Thank you.

@elliotthensley8844 3 жыл бұрын

Hey I have a 330i ZHP and my car rattles while I’m neutral usually only when it’s cold. When I press in the clutch it stops. Wondering if it’s the pin or the throw out bearing or something else? Need help ASAP!

@Brux7777 2 жыл бұрын

Hi, my cousin just 525d touring F11 , manual gearbox and the shifting on 2nd always cracks. Any sugestion? Best regards

@anjolguzman9236 3 жыл бұрын

The gs6 53dz fit in a m54 engine? Please answer

@nwsk00 3 жыл бұрын

my e36 is stuck straight in gear im so bummed idk what going on i was power shifting thought cause it was cold

@dominiquesantiago7618 2 жыл бұрын

Hey man is there any way we can set up a zoom or face call i have some questions man

@CNCant Ай бұрын

Thank you for these videos. I have 2006 325xi manual. Bought it as a project car. There is a problem with gearbox/shifter. I can shift into a gear without depressing the clutch on a running vehicle. Shift feels and sounds normal, but nothing happens. Stuck in neutral. Please help

@freemanmiracle7975 2 жыл бұрын

What can cause cold start hard to shift into 1st or reverse even after new fresh ATF fluid change on my E46 330i 6 speed. It is smooth after warming up or driving around. Can that pivot pin cause this problem?

@ismaeladame9031 2 жыл бұрын

I have a question I have a 325.I if I going reverse it jumps off gear and if I driving and I put it to neutral and put it to 2 gear it won’t let me idk if it the shift non or transmission

@teodorjitcu7262 3 жыл бұрын

Hi I have a bmw 520d f10 2010 manual...and I can't put it in reverse! I don't know why... all 6 gears and clutch works perfectly

@gyimpity 2 жыл бұрын

Hi, You might be the guy to answer this, I have a 330Ci 6 speed 2004, First gear is very notchy and sometimes is almost impossible to stick it into 1st at the lights. any ideas? goes in easier if the car is still rolling.

@garypearson8556 3 жыл бұрын

My 98 BMW M3 with 6 puck racing clutch is still hard putting in gear I bled the clutch with a syringe and got all the air out of it please help

@johnberry9415 3 жыл бұрын

Hi, I have 330ci 2003 automatic transmission, in this year am remplace 3 times the flexplate triangle go with the torque converter make a lot noise after 2 moth , I like to know any experience abaut and why happened several times, thanks.... For anyone help...