BMW E60 CCC computer coding/programming. The easiest way...
Рет қаралды 149,278
7 жыл бұрынConsider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
This car came to me to install and code/programme a CCC (Car Communication Computer), on a 2005 BMW E60 545i.
The original CCC was completely dead, the diagnostic machine could not establish communication with the module or sub modules of the CCC,to I was show you this "no communication", but run out time...
A second hand unit was installed.
In this video I will demonstrate how to code the module to the car, this way is in my opinion, the easiest way...
Hope you enjoy the video.
Any questions put them below.
Like always, thank you for watching!
@jmanpt9157 6 ай бұрын
For all of those having problems after ccc replacement. Do the following: 1. Load NCSExpert. 2. Load Profile and select Expertmode 3. F1 (VIN/ZCS/FA) 4. F3 (ZCS/FA f .ECU) 5. Choose the right chassis 6. Select CAS/LMA 7. F6 (BACK) 8. F4 (Process ECU) 9. Select the Module you want to revert back to Factory 10. F2 (change job) ->Choose "SG_Codieren" 11. F3 (execute job) ->to start coding the ecu with factory settings according to the vehicle VO. The ecus codded will grab the available options from the V.O. no need to manual change anything. Repeat process for these ECUs: CHOST CAPPL CGATE CAUDI CTUNE
@LMAutoRepairs 6 ай бұрын
Thank you for summarise the video...👏 👍👍👍
@JL-wf2wp 5 ай бұрын
Howdy guys, is the listed process for those 5 ECUs going to fix my issue of having no audio? I recently succesfully reflowed my CCC unit. Now it works without rebooting itself but I have no audio ever since 😅 Thanks in advance 🙏 Greetings from Spain!
@DymondeLuv 4 ай бұрын
Hey! Please some help! Mine has 2 profiles. Factory and manipulation. Which one can I use?
@DymondeLuv 4 ай бұрын
Sorted 🎉🎉 thank you for the information! Used your advice and now my sound is on! Thanks a bunch!
@DymondeLuv 4 ай бұрын
@@JL-wf2wpyes it will work!
@Hammaneggs88 6 жыл бұрын
Awesome video. I'm in the process of swapping a ccc from an 07 M5 into my 04 545i. We have come across a couple issues that I think this video covers greatly. I'm praying this is the answer. Have a Blessed Day.
@LMAutoRepairs 6 жыл бұрын
jason hamman Thank you for the nice comment, hope you get it sorted...
@michaelclark2610 2 жыл бұрын
@@LMAutoRepairs q . B... B ,
@michaelclark2610 2 жыл бұрын
@@LMAutoRepairs Yeah I did I flash rs delete by itself, locked the dme, had the ftdi set at 115000 instead of 9600.. then I figured it out. Flash the RS and tune together, then go and recode half the modules... Don't wonder why no power to fuel pump , recode the ekpm and your car will work again lol. Thats what I just went .. pocket comment lol
@The911nut Жыл бұрын
Thank you! I had to replace my CCC, Logic 7 (option code on FA string $677) audio system dead afterwards, had to recode: - CGATE - CHOST - CAUDI - CTUNE - CAPPL Then you must reset CCC in order for programming to take effect, otherwise Logic 7 will not turn on. Hold both eject buttons on CD/DVD and Vol button in until screen goes blank. After the reboot, the audio system came on beautifully! This is the best way to recode your new CCC, trying to figure out German and the individual options is not a good way. BTW, I used basic NCSexpert with only the two profiles.
@LMAutoRepairs Жыл бұрын
😊 👍👍👍
@benjaminlopez8932 7 ай бұрын
Hi is there anyway you could walk me through the steps you mentioned I’ve replaced my ccc headunit since my navigation screen was black now screen works but have no sound.
@JL-wf2wp 5 ай бұрын
@@benjaminlopez8932 I have the same issue.. I reflowed mine and works properly without rebooting now, but no audio 😢 did you find a solution? 👀
@phr3ui559 4 ай бұрын
what is the CCC ror
@JL-wf2wp 4 ай бұрын
@@phr3ui559 ror?
@Ricardo_Caracol 7 жыл бұрын
Great video amigo!!! thanks
@LMAutoRepairs 7 жыл бұрын
Ricardo Mendes Obrigado! Thank you!
@stevemartin7321 6 жыл бұрын
Thanks for sharing your skills great help
@LMAutoRepairs 6 жыл бұрын
Steve Martin Thank you!
@ianmatterson5632 Ай бұрын
bloody awesome info fella..THANK YOU SO SO MUCH for sharing and taking the trouble to create this tutorial, your a star
@LMAutoRepairs Ай бұрын
😊 👍👍👍
@ianmatterson5632 Ай бұрын
@@LMAutoRepairs i'm going ccc to cic retro, does this mean i can only have /program the functions of the original ccc but with the new cic menu layout?
@LMAutoRepairs Ай бұрын
Yes... apart from some the CIC functions that you can also retrofit...
@ianmatterson5632 Ай бұрын
@@LMAutoRepairs well fingers crossed my 'upgrade' goes smoothly, i cannot believe the trouble those headunits gave you, talk about pushing ones limits, but should i need help would you mind if i dropped you a question or two if needed fella?
@Enis901 Ай бұрын
Hello! i have a question can i take any ccc unit and code it? it's like i bought a ccc unit from a pre lci car and mine is lci so now i get no sound haven't coded anything yet.
@stephenchalkley7848 5 жыл бұрын
Thanks very informative great skills
@LMAutoRepairs 5 жыл бұрын
Thanks! For watching and for your comment!
@janimughal7180 5 жыл бұрын
Hey lm Could you also tell me where to get the file to fully recode and update my ccc of bmw e60 530i 2004
@LAU3768 5 жыл бұрын
thanks for share your skiils , Great video
@LMAutoRepairs 5 жыл бұрын
Thank you for watching!
@colinlyne1660 6 жыл бұрын
gosh! Imsvvavr you make it seem so easy. but I know I have to do some google sereches for the softwear which I guess is outthere. many thanks for fantastic videos and education I love it cheers colin
@LMAutoRepairs 6 жыл бұрын
colin Lyne If you get the cable from the right place, will come with all the software...😉
@andreikelemen1530 4 жыл бұрын
Where i can found you mate. I got same problem with a bmw series 5
@ahmed-ty9zg Жыл бұрын
Hello my friend thankyou for your videos. Im wondering if you can help me im trying to connect an obd2 port to my ccc bench setup to code the ccc ive connected the can hi can low and 12v/grnd to the cas3 What else would i need please?
@MasterX767 7 ай бұрын
GREAT VIDEO! THANKS A MILLION!
@LMAutoRepairs 7 ай бұрын
☺️ Thanks! 👍👍👍
@Samb-ps6vk 4 жыл бұрын
Hi, I need to have a cic code/flash. Is this something you can do remotely?
@mrjesus61 3 жыл бұрын
excellent video, one question: when you buy cc used for e 60 does the audio need codinig?
@LMAutoRepairs 3 жыл бұрын
When you code the unit, it codes to the VO... so everything gets coded to the car specifications... Thank you for watching!
@moeluai5081 4 жыл бұрын
Very good straight forward video!. I have a question, will an E60 ccc unit fit an E90 ccc. Reason for my question is that they don’t share the same part number
@LMAutoRepairs 4 жыл бұрын
Most likely it will work... You will need to change the front fascia etc... and program it correctly... But I never done it, so don't take my work for it... Thank you for watching and for your comment!
@aimized1460 2 жыл бұрын
Yes it will fit a e90 and it will work once plugged. I can confirm this because my car is a 07 328xi ccc. My ccc died and I replaced it with one from a e60 as the cost for a e90 one was more than double… everything works except you will have to get the front trim panel to fit over the e60 one as it’s different trim cuts and sizes this is literally the only thing you should be worried about, is finding that trim piece to cover that ugly exposed ccc box or you don’t have to cover it with trim but it looks like crap. Edit if you want to match the VO numbers use a app like inpa to reprogram the coding but it’s pretty pointless to do unless your missing features that you had before but don’t have them now get it ? Cheers
@pawelm4502 6 жыл бұрын
good stuff
@LMAutoRepairs 6 жыл бұрын
Pawel M Thanks! 👍
@rameshm2100 2 жыл бұрын
thanks for taking time and explaining this in detail. will this instruction work for szl module?
@LMAutoRepairs 2 жыл бұрын
Yes... obviously the coding will be different, but the principle is the same...
@rameshm2100 2 жыл бұрын
@@LMAutoRepairs thanks I am going to try it today
@SuperInterpol1 4 жыл бұрын
Thanks for a nice video, I can do the same with the BMW F model.
@LMAutoRepairs 4 жыл бұрын
Yes.... but not with this software... F series is slightly different... Thank you for watching and for your comment!
@SuperInterpol1 4 жыл бұрын
@@LMAutoRepairs I have E-sys program and E-net cable which is for F series, do you think I can do the same programming or coding?
@LMAutoRepairs 4 жыл бұрын
@@SuperInterpol1 Yes... E-sys is the one... you can do coding etc...
@arditpashollari3025 3 жыл бұрын
Hi Need to code bmw e60 when retrofit climate control from pre-lci to Lci
@palflemmingryvnge6644 3 жыл бұрын
I skipped changing the VIN numbers on the modules last time, what is the purpose? I guess this is not needed?
@osmancinar7042 4 жыл бұрын
I need help for coding aux in my bmw e 64 you can help me ?
@gari4kata 3 жыл бұрын
Thanks very, Nice 👍
@LMAutoRepairs 3 жыл бұрын
Thank you for watching and for your comment!
@interestingthings4404 5 жыл бұрын
Great video, thanks for sharing it. I have 2008 E60 528i which doesn't have USB input for audio system, I know the premium package comes with this option. If you don't mind to tell me how I can code USB so it comes as available source to play music and what is the part number for USB cable connection is needed ? It would be great if you walk me through this process thanks already and have a blessing day.
@LMAutoRepairs 5 жыл бұрын
Hi You need to replace the TCU with a MULF high if I am not mistaken... and then all the wiring etc... it is more than just coding... Thank you for watching and for your comment!
@interestingthings4404 5 жыл бұрын
@@LMAutoRepairs , Bluetooth on this car is the first generation and only works for cellphone calls , you think is doable to upgrade so I can stream music from ? Thanks in advance .
@LMAutoRepairs 5 жыл бұрын
@@interestingthings4404 Doubt... that feature was not released untill a few years later.... Unless you check a dension system....
@thewhitestar206 Жыл бұрын
Anyone know what is (create fast boot image on INPA? My logo stuck:( Update! Old CCC unit is dead no wonder doesnt boot up, I replaced with m6 used ccc unit n coded via inpa. Working good now.
@giolz6379 4 жыл бұрын
Hello, question for you...I installed CCC from different car into my 2006 530xi...when I try to go in the menu with the wheel, it jumps from the top option to the last option but not in between. Is this because it is not coded or do you think something is wrong with my iDrive wheel? Thank you for this great video and information.
@LMAutoRepairs 4 жыл бұрын
Could be coding... but check live data... see what the wheel is doing... Thank you for watching and for your comment!
@sadikmamoun2847 6 жыл бұрын
hello there i would like to ask you for some help i have a case of a bmw e90 ccc that came to me with a rebooting problem the screen is white and it reboot itself i have serched the internet for a solution which i found that i have to reflow some chips on the pcb module but i don't know if it is going to work or should i replace it with a used one if so do i have to code it
@LMAutoRepairs 6 жыл бұрын
sadik mamoun Hi I have successfully reflowed one or two in the past... if that doesn't work then a second one, which yes, most likely will need coding...
@Nmax92 6 жыл бұрын
Great video, very informative. I have an issue with my 2006 E60. Here is the problem. 1. My keyfob does it lock or unlock the doors. I can disarm the car by putting the key in the door and if ignition. 2. In the iDrive, the bluetooth signal is not showing. I can check and uncheck the bluetooth in the communications menu but the bluetooth doesbt come on at all. 3. I checked the module in the boot, there is light on the fiber optics cable. When I unplug the bluetooth module and plug in the white connector, I can see a red light flash for a few times, but then it goes away. Any suggestions?
@victormachuca6621 3 ай бұрын
Ever figure this out? I’m having the exact issues down the letter
@trapmusicplug8388 Жыл бұрын
I found a easyier way to code aux in it worked for me since i dont know how to code and only care about audio. It worked perfectly
@trapmusicplug8388 Жыл бұрын
You need to change ecu (CHOST,CAPP,CTUNE,CAUDI,CGATE ) to match VO of vehicle, i then coded aux config to active thru bimmercode app on my phone. And it worked
@trapmusicplug8388 Жыл бұрын
To change VO Open NCS Expert - Load an Expertmode profile - Press F1 button - Select F3 and choose your car chassis from the list - Click OK and choose CAS from the list. (This is where NCS will read your VO from) - Press F6 - back - Press F4 - process ecu and Choose the ECU your would like to code with factory default options of your car - Press OK - Reset BMW ECU to factory setting - Press F2 change job - Choose "SG-CODIEREN" - Press OK - Press F3 "Execute Job" to start coding the ECU with factory setting according to your BMW vehicle order (VO) - ECU resetting is done. Change ECU to next module
@trapmusicplug8388 Жыл бұрын
No guaranteed to work but worked on mine i replaced my ccc unit but the aux was not greyed out but no sound came out so it was still under another vo
@LMAutoRepairs Жыл бұрын
@@trapmusicplug8388 You did essentially the same thing, but using two different things... You can do everything using NCS and/or the BMW tools... Thank you for watching and for your comment, surely will help others... 👍👍👍
@thewhitestar206 Жыл бұрын
@trapmusicplug8388 hello I need help, I accidentally clicked (create fast boot image)under INPA now my screen stuck logo. How do I reset this? Thanks
@mtillers88 6 жыл бұрын
Hi . Thanks for video. Got problem whit e60 radio . It's on mute and no chance to get off. Thinks unit gone . How can I code diferent unit to car? Are it's need to be same part nr . ? Thanks for advance
@LMAutoRepairs 6 жыл бұрын
Maris ti Not necessarily the same part number... but the same type of unit yes... I explain here how to get it coded... Hope that helps... Thank you for watching!
@Devilek1986 3 жыл бұрын
@LM Auto Repairs HI. It is very good viideo mate but could you tell me why when i type in my e63 vin it shows my Vin i faulty ? did u had that problem before? kind regards Dan
@LMAutoRepairs 3 жыл бұрын
Make sure you have all the daten files for your chassis, and NCS setup correctly... Thank you for watching!
@jordancobb2688 2 жыл бұрын
What cables do you use and how/where do you connect them
@LMAutoRepairs 2 жыл бұрын
Look for BMW D-Can cable... What do you mean, where I connect it? 👍👍👍
@dsmith2983 7 жыл бұрын
I got a used CCC from another car everything works but the audio plus the new system has 6 CD changer and bluetooth which mine do not. Do I need to get the new system coded?
@LMAutoRepairs 7 жыл бұрын
D Smith Hi If you want to get rid of the menus and functions that do not apply to your car, yes...
@ANSt15 7 жыл бұрын
I’d like to know what cable and software do you use. If you could please put links under the description below on where to get them in America. Thanks.
@LMAutoRepairs 7 жыл бұрын
STANLEY MOISE Hi Just Google 'bmw cables'... eBay might be a good place to start...
@matthewwhitmus1608 Ай бұрын
if you replace the ccc with another 2nd hand ccc with the same features. is it neccessary to change the vin? if i dont, will all the features work such as radio, maintenance schedules, oil level, etc
@LMAutoRepairs Ай бұрын
Should work if all the other features are correct... 👍👍👍
@andyheyman5738 5 жыл бұрын
Hi I have a error head unit not programmed correctly. I have been told that head unit is not original so need to change vin numbers. Can I bring car to you I am in bedford near Peterborough.
@Mambre79 7 жыл бұрын
Great video, thanks. What cables do you use for both softwares? I use k dcan inpa cable for coding, can I use it for the other programme BMWdash?
@LMAutoRepairs 7 жыл бұрын
Hi Thank you for watching and for your comment! As per the video, INPA can actually be used for both, coding and VIN change... however the VIN change with WinKFP it is a bit more tricky than with BMWDash.... BMWdash however, can not do the coding... (Theoretically it can, but even more complicated...) So, easiest way is INPA (NCS expert) for the coding, BMWDash for the VIN number changes...
@gunti80 7 жыл бұрын
lmsvvavr what interface do you use for bmwdash? isit possible to use dkan cable for the bmwdash software or have to get new interface? and which1? thanks.also can you do a video for programmi g a used dme or dde.thanks.top videos
@LMAutoRepairs 7 жыл бұрын
gunti80 Hi If there is a way of using d-can cable for BMWDash I am not aware of it... The interface comes with the software... just look for BMWDash and you will find it... When I have one to do and time to record it is will make a video for it... Thank you for watching and for your comment!
@gunti80 7 жыл бұрын
lmsvvavr cheers top videos top man.
@LMAutoRepairs 7 жыл бұрын
gunti80 Thank you!
@sorin-stefanalbu2933 Жыл бұрын
The same on BMW 320i E90 2006 (CCC Professional)
@dennisf726 4 жыл бұрын
Hey i need help with my E60 04. I bought a second hand CCC headunit from another E60, but I can only flick the Idrive weel up, down, left or right to go into a menu, but i can't turn it to choose witch option i want. Does it need coding? and if so, witch code?
@LMAutoRepairs 4 жыл бұрын
Never had to code nothing like that... Check live data for the controller... make sure is working correctly... Thank you for watching!
@marbury417 5 жыл бұрын
Can you please share the software that you use to change the VIN ... I am going to be doing this same process as I am replacing my CCC in my E60
@LMAutoRepairs 5 жыл бұрын
I actually said the name of the software during the video... BMW Dash Thank you for watching!
@theunick7879 Жыл бұрын
@@LMAutoRepairs Can I use kdcan cable to make it?
@LMAutoRepairs Жыл бұрын
Not for BMW dash...
@MrMintOne 5 жыл бұрын
Hi, i have ccc and bluetooth which i can only make phone calls, so is it possible to code it full bluetooth access that i can play audio?
@LMAutoRepairs 5 жыл бұрын
Hi No really... was not an option back then... Thank you for watching and for your comment!
@swekz Жыл бұрын
one thing that you skipped was after you was in ncs dummy did you edit the file there or did you just edit the .trc file in notepad and after that coded that file in ncs expert?
@LMAutoRepairs Жыл бұрын
NCS dummy it is just a helper that translate some of the coding... You can edit just the .trc file and code... You don't need the dummy software... 👍👍👍👍
@beudeanandrei 4 жыл бұрын
Hi buddy. I want to activate some settings in my IDrive CCC Business...and when processing the ecu I don't find the capps module...what should I choose? I want to activate the phone dialing option. Thanks
@beudeanandrei 4 жыл бұрын
I forgot to mention it's a e87 LCI 2007
@bam88 4 жыл бұрын
hey how about e65 ASK unit? any tutorial to replace it?
@LMAutoRepairs 4 жыл бұрын
Same principle... but I never done one... Thank you for watching!
@zsombi1758 5 ай бұрын
Hello! If your car has the same functions like the car you are bringing the donor ccc unit from, do you need to do any kind of coding? (even if the numbers on the units are not the same)
@LMAutoRepairs 5 ай бұрын
Possibly will be ok without coding... But it is highly recommended to have it done... 👍👍👍
@sandyjoe1047 7 жыл бұрын
Thanks for the awesome Video. I ran into an issue trying to code my CCC, I have a 2006 BMW 330Xi (E90). NCS expert do not have E90 chassis to choose so I found out from few other KZfaq videos that I should select E89. So I selected E89 and press Ok, another window pops up and asking me to Enter my VIN number, so I did. then it says "Faulty VIN". Why does it asking me for the VIN number ? I thought NCS Expert will retrieve that information from the car automatically? how do I proceed from here? Appreciate your help.
@LMAutoRepairs 7 жыл бұрын
Thank you for your comment! NCS should indeed retrieve the car details... Does INPA connects ok?
@sandyjoe1047 7 жыл бұрын
I figured it out, one of the configuration files for NCSEXPERT was missing. I downloaded it and copied it to bin folder. after that NCSEXPERT retrieved the car information and I was able to code it. Thank you so much for making this video. I was able to code my CCC successfully and now I have sound in my car. I was driving around for over a year without sound. Can't thank you enough for this tutorial. YOU ARE THE BEST !!!
@LMAutoRepairs 7 жыл бұрын
Hi Sandy! Thank you so much for the nice comment! Really good and satisfying, to know that you manage to get it sorted, and that some how my video has contributed towards to that!
@ryvaenge 4 жыл бұрын
BMW E60 2005, CCC unit had a long time troupble with rebooting, suddenly dead. Sent for repair, came back working with no sound. Bought cable and NCS expert. After reading out the data TOP_AMPL_TYPE: nicht_aktiv. Wrote back with FA info, it was correctly set to "logic_7". Still no sound. I could test sound from INPA from the Amplifier, that worked. Any ideas? One thing I was curious about in INPA, was: MOST CAN gateway ccc - status amplifier Mute: OK ??? Could this mean something like it is muted?
@LMAutoRepairs 4 жыл бұрын
A possibly... However, if everything was working before, I mean the sound obviously, as I understand the unit was faulty otherwise, I would check with whoever done the repair.... in case is something in the unit itself... i would start by ask if the repair would affect the coding of the unit.... Thank you for watching!
@soso94940 6 ай бұрын
Hi, was the original ccc rebooting all the time ?
@LMAutoRepairs 6 ай бұрын
No... I have explained the problem in the first 60 seconds of the video... The is one, the replacement unit had that issue... check here... kzfaq.info/get/bejne/fLepqJepx9Wdkok.htmlsi=QTGhnqFQTLMBeIga 👍👍👍
@samgod 10 ай бұрын
I swapped the dead CCC unit in my '06 330i with one from another '06 330i and it just flashes a white screen every few minutes instead of booting. Is this because it's not coded to my VIN and VO?
@LMAutoRepairs 10 ай бұрын
No... That means the unit is most likely bad... Double check connections, etc... but that sounds like a bad CCC... 👍👍👍
@XXandercageXX 3 жыл бұрын
hi , I want to activate voice control on e61 with CCC , this voice control not been active from factory , it is possible to activated? ty
@LMAutoRepairs 3 жыл бұрын
Yes... but you need the correct modules installed first... Plus the switch in the center console etc... Thank you for watching!
@DjTavy Жыл бұрын
Great video. I bought a ccc unit from a saloon car installed on my estate car and when I reverse on display show the wrong car model. How to change that? Also my climate won't stay on my settings is going on default everytime when I try to play with. Any idea please? TIA
@LMAutoRepairs Жыл бұрын
Have you coded the unit to your car? 👍👍👍
@DjTavy Жыл бұрын
@@LMAutoRepairs No, I didn't. I have Inpa and ista+ but I don't know where to find the module.
@LMAutoRepairs Жыл бұрын
You need toncode the module to your VO... Once that is done all the settings will match your car... 👍👍👍
@miroshatri8408 7 жыл бұрын
i am just traying to fix my own car and since i cant find a good programer anywhere near me i need to do it myself anyway i am from croatia so it is not an option that i come by so you can look at my car
@LMAutoRepairs 4 жыл бұрын
Hope you got it done! Somehow I missed your comment...🤦♂️
@mafilove07 Жыл бұрын
Can you do a coding on my E60? I have the new CCC facelift from last model. Shows Bluetooth as in you’re video but I don’t have. Please
@LMAutoRepairs Жыл бұрын
Just code it to the VO... 👍👍👍
@mafilove07 Жыл бұрын
@@LMAutoRepairs I’m not an expert …
@kathijakhan2548 4 жыл бұрын
Hi please tel me sir if my e90 module dont need to code any settings can i just code it without going to man trace file to modify any settings?
@LMAutoRepairs 4 жыл бұрын
You can code it to the VO.... and it will be coded to the options fitted on the car... or factory settings... Thank you for watching and for your comment!
@kathijakhan2548 4 жыл бұрын
Thanks for your reply😊
@makoesim 5 жыл бұрын
Hi I bought a used ccc and i coded it in my car following your instructions using ncs expert, now seemed everything works fine, is it necessary to change VIN numbers ? Cause i don't have bmw dash tool Thanks
@LMAutoRepairs 5 жыл бұрын
Hi That's great! You should get away without coding the vin... Thank you for watching and for your comment!
@makoesim 5 жыл бұрын
@@LMAutoRepairs then why everyone want to change the vin number ? Is it all about the voice command ? I have winkfp but there are tons of modules and it hard to tell which one require vin change Sorry for my bad english
@LMAutoRepairs 5 жыл бұрын
@@makoesim Yes... don't you have someone that can do just the vin change? I rarely used kfp to be honest...
@makoesim 5 жыл бұрын
@@LMAutoRepairs unfortunately no, bmw not so popular here in iraq, voice commands is not very important to me however i will try to change vin and fsc depending on what i can find from internet sources Thanks again
@MooGu95 4 жыл бұрын
Hey LM. I have a e60 nfl and i buyed my car with lci clima. The problem îs can't modify air distibution, any idea please!? Thanks
@LMAutoRepairs 4 жыл бұрын
Needs coding... most likely... Is the idrive the ccc or cic?
@StudioSasha Жыл бұрын
Hi ! I have BMW 528i e60 LCI 2010 . Uriginaly have 6.5 screne. Im upgrade to android 12 carplay . all work perfect,but switch screne to classic problem resolutions, after com to android factory settings and change resolutions not work for me. how to fix this ? Make diagnostic on ISTA D all Three Green only CID red ? Help Please. Thanks ,Best Regards,Alex
@LMAutoRepairs Жыл бұрын
When you start to mix systems, many things can go wrong or not work as intended... I can advise in this case... just double check the coding and the connections etc... 👍👍👍
@OneAuto 7 жыл бұрын
Will you be opening the CCC to see what was wrong with it? I feel that soldering iron heating up!
@LMAutoRepairs 7 жыл бұрын
LOL... well, I had a few repaired in the past, have although never done a video for it... This units tend to suffer from different issues... in this one I am pretty sure it is going to be the capacitors in the power supply area of the board... as the unit was not even booting... The car and the old unit have already been picked up... will for sure make a video of the repair when another one comes with a bit more time... Thanks...
@A.c97 7 жыл бұрын
lmsvvavr I hope you make this video because my 2005 bmw 530i is stuck on the bmw screen and will turn off and on nothing more comes up
@amatlense07 4 жыл бұрын
@@A.c97 did you fix your "screen stuck at BMW logo" problem?
@amatlense07 4 жыл бұрын
@@A.c97 if you did what was the problem?
@A.c97 4 жыл бұрын
amatlense07 I did fix mine a few years ago i ended up selling the car but what I did was I took the ccc unit out of another 5 series at the junk yard luckily the owner gave me the whole junk car to take off anything I wanted for free. The ccc units last I checked a few years ago was 300$ but if you can get it out of another car it’s worth it and super easy to replace I did it when I was 17 years old . Also have you tried to restart the unit I believe you press volume and the eject button and also another button I can’t really remember but you can look it up
@youessay7983 Жыл бұрын
Hi thanks for the awesome videos, iv e just replaced my e60 motherboard with one from an e90 lci that had pre set buttons when i try it with my faceplate it doesnt work but works perfect with the e90 faceplate. Do you know if theres a way to code my faceplate to the motherboard pls
@LMAutoRepairs Жыл бұрын
I don't think that is possible... I mean, possibly by flashing the module, but doubt it can be done by coding... 👍👍👍
@youessay7983 Жыл бұрын
@@LMAutoRepairs Thanks for the reply. Would default vo coding to my car not work in this situation then
@LMAutoRepairs Жыл бұрын
Not really... that codes the options for the car, not the specifics of each hardware...
@youessay7983 Жыл бұрын
@@LMAutoRepairs oh desr looks like the motherboard was a waste of money then. Thanks for your help
@smoothie1000 Жыл бұрын
Do you need a special cable for the dash tools or can you use same cable for inpa/ncs expert? Is the software free?
@LMAutoRepairs Жыл бұрын
It is a different cable... 👍👍👍
@smoothie1000 Жыл бұрын
@@LMAutoRepairs I updated donor CCC with the VO - it all works fine. Should I care about updating the VIN?
@LMAutoRepairs Жыл бұрын
Not really necessary, but if you have tools, I would do it...
@fredblogs3871 Жыл бұрын
hi great vid .. can you tell me plz if BMW dash can run on windows 10 if i put in win xp compatibility mode ?
@LMAutoRepairs Жыл бұрын
Never tried it... sorry... I have XP on a few laptops to run old softwares... But hou can try it... Or try a VM 👍👍👍
@fredblogs3871 Жыл бұрын
@@LMAutoRepairs thank you i will give it a try
@user-oy9fj4ec6i 8 ай бұрын
Great video. So helpful but I’m trying to find the software for BMW dash. Can’t find it anywhere. Can you help me? Need to code a replacement radio to my cars vin
@LMAutoRepairs 8 ай бұрын
You would still need the interface... As as far as I am aware, Dash only communicates with its own interface... 👍👍👍
@user-oy9fj4ec6i 8 ай бұрын
Thank you but where can I buy it or find it? I’m also trying to use WinKFP as an alternative but I missing some sp-Daten files I can’t find anywhere ☹️
@LMAutoRepairs 8 ай бұрын
Not sure where to get dash interface from... bought mine years ago... The spDaten you cN find them... dig a bit deeper...😉
@user-oy9fj4ec6i 8 ай бұрын
@@LMAutoRepairs thank you. I managed to get the spaten files I needed. Now I’m running into another snag. Hopefully you can give me some insight. Trying to code aux using ncs-expert but getting an error. I tried to add +NAUX to the VO but I’m getting the dreadful “Following feature is invalid for FA: + NAUX” from my research it seems many have encountered this but no one has a fix.☹️
@LMAutoRepairs 8 ай бұрын
@user-oy9fj4ec6i Skip that step... Manually activate the auxiliary on the CCC... See if that works... 👍👍👍
@wesleyd4310 4 жыл бұрын
How do I code ccc with logic 7 to a car without logic 7. What are all the tools I need? Please help!!
@LMAutoRepairs 4 жыл бұрын
As per the video.... it is all you need... Thank you for watching!
@tobertb 4 жыл бұрын
Wherer can I find a full version of ncs expert with all the dat files?
@LMAutoRepairs 4 жыл бұрын
You don't really... Unless you find it already packed... NCS is the software... you then need the correct SP-DATEN files for the car you are working on... Thank you for watching and for your comment!
@shemied2570 3 жыл бұрын
@@LMAutoRepairs can you code my ccc head unit online using my network
@robertban851 3 жыл бұрын
Hello! And congratulations for video! Can you help me with a situation pls? On my e91 i have ccc business navigation on small display. I put a ccc professional navigation with big display on it. I try to code like in your video, but the CAPPL ecu is not in my list in NCS Expert. What can i do? I'm stuck... :(
@LMAutoRepairs 3 жыл бұрын
Hi What have you changed, just the screen? Thank you for watching!
@robertban851 3 жыл бұрын
@@LMAutoRepairsHi, I change the screen and the navigation (that piece under the climate panel, wiht 2 cd/dvd entry)
@LMAutoRepairs 3 жыл бұрын
OK Change the VO first... Remove the Mask and add the CCC... Code the whole car, and everything should work...
@UDRElectronics Жыл бұрын
So just to understand.. until min 19:46 you show the "usual procedure " to code the new module but the best and easiest way is from 19:46 further
@LMAutoRepairs Жыл бұрын
Hi Not exactly... You must have skipped parts of the video... as I have explained it all... 😉 👍👍👍
@camargovideos6612 3 жыл бұрын
Hello had you replace a module with hw 9.8 for hw 12.5, and no sound issue bc the 12.5 is for logic 7 amp
@LMAutoRepairs 3 жыл бұрын
I obviously can't remember now those sort of details... all the ones I have replaced always worked like a treat... make sure you code/encode everything accordingly... Thank you for watching!
@camargovideos6612 3 жыл бұрын
Do you have any video where you code the radio from logic 7 to stereo?
@LMAutoRepairs 3 жыл бұрын
No... But you be able to do it by just remove logic 7 from the VO... Thank you for watching!
@bym007 7 жыл бұрын
Great video mate. You really clear a lot of coding steps and questions. I have a question for you. My CCC unit died and I replaced it with a used CCC unit (slightly newer CCC unit with felt touch buttons). The previous one was same as your video. I installed it and it was working fine, except the iDrive controller does not work. What needs to be coded ? Thanks for reading.
@LMAutoRepairs 7 жыл бұрын
Babar MUGHAL Hi Thank you for watching and for your comment! So, you have installed a NBT system?
@bym007 7 жыл бұрын
The unit is an updated version of the CCC, resembling this picture. (revtronic.com/wp-content/uploads/2014/04/BMW-CCC-PROF.jpg). The iDrive Controller does not work. Thanks for replying.
@LMAutoRepairs 7 жыл бұрын
Babar MUGHAL Can't really say much... CCC or CIC should work with the same controller... Not sure about NBT... If yours is not working, first of all ask the people who sold it to you... they might be able to help. If that is not an option, diagnose the car, to make sure the controller is working correctly... if is working, check coding...
@mikigorov994 7 жыл бұрын
can it be done with abrites for bmw?
@LMAutoRepairs 7 жыл бұрын
Miki Gorov Hi Can't tell... I do not have that tool... Look at the literature for it...
@synter3843 Жыл бұрын
Hi ive damaged my nit with andriod do you know which chip is video card pls?
@LMAutoRepairs Жыл бұрын
What do you mean? An aftermarket unit? 👍👍👍
@synter3843 Жыл бұрын
@@LMAutoRepairs Hi sorry i should have read that back before sending lol. I fitted an android screen to my ccc now i have no screen but sound is working. after googling i see the cause is the android screens damage the video card/chip of the ccc. do you know which chip controls the picture pls
@Cristi10077 5 ай бұрын
My CCC has NO chime(parking sensor sound, bmw GONG) but I have music What’s wrong with it??
@LMAutoRepairs 4 ай бұрын
Hi Have you scanned the car? What is the background of the problem? 👍👍👍
@smoothie1000 Жыл бұрын
Can I just save my existing ccc CAPPL RCU and load it into the replacement one?
@LMAutoRepairs Жыл бұрын
Not really... I mean, you can if both have the exact same SW version... otherwise can cause issues... Best thing is to just code the CCC to the VO... I have videos on that... 👍👍👍
@smoothie1000 Жыл бұрын
@@LMAutoRepairs does the car already know what features it has and can it automatically code to the replacement ccc ? I plan to buy a used one off eBay.
@LMAutoRepairs Жыл бұрын
@@smoothie1000 Yes... all the options of the car are stored in the VO... so, if you code the car to the VO, everything will be set to your car... 👍👍👍
@4aces814 9 ай бұрын
i install big screen on mask2 and resolution is different can you show how to coded screen for right resolution?
@LMAutoRepairs 9 ай бұрын
You can do it with NCS expert if I recall correctly... by changing the screen size in the coding settings... 👍👍👍
@4aces814 9 ай бұрын
@@LMAutoRepairs i cant find this option by anychance you can do video
@LMAutoRepairs 9 ай бұрын
@4aces814 I don't have a car to try... Buy if you don't see the option, your mask might not be capable of an higher resolution... Upgrade the head unit...☺️
@arditadili6936 2 ай бұрын
Hi I got a new ccc unit because the old one wasn't working on my e92. The new ccc has restored all the functions but no audio. How do I code that in, and if applicable do you know how to do that with bimmercode?
@LMAutoRepairs 2 ай бұрын
Never used bimmercode, but NCS expert will do it... Just code everything to the VO... 👍👍👍
@arditadili6936 2 ай бұрын
@@LMAutoRepairs Gotcha, I don’t have a windows laptop. I just have a Mac. I’ve tried looking at different videos on how to get it on my mac. Do you have any more straightforward information. As to how to even download NCS expert on a mac? I appreciate all the help so far!!
@LMAutoRepairs 2 ай бұрын
No... not a mac used... perhaps with some sort of virtual machine...
@kevinhumbert5183 7 жыл бұрын
This an awesome video. Can you help me figure out how to resolve my Bluetooth not work?
@LMAutoRepairs 7 жыл бұрын
kevin Humbert Hi Which car are we talking about?
@kevinhumbert5183 7 жыл бұрын
The bmw e60 bluetooth system.
@LMAutoRepairs 7 жыл бұрын
kevin Humbert OK... Those modules are known for giving problems... what are you symptoms? Is not working at all?
@kevinhumbert5183 7 жыл бұрын
My only thing that is not working is the bluetooth.. The car see the phone, pairs to the phone but will not connect. It shows the phone on the screen and on the phone as well but will not connect at all for any bluetooth usage.
@LMAutoRepairs 7 жыл бұрын
kevin Humbert Which phone are you using? Just to test, have you tried another phone? Remember that if your car is one of the old models that never had a software upgrade, it might suffer from connectivity and compatibility issues... if that makes sense...
@gritsgong 6 жыл бұрын
Hi I have the annoying airbag light code 93F9. I replaced the positive battery cable but still no luck. I have a vehicle inspection coming up soon and I won't pass with the dreaded airbag light 😩. I bought a used SGM/gateway security module and airbag module. If I install this on my car then do I have to flash / recode this module to my car for it to work? I'm kinda scared to juts plug it in because I'm it sure if it will through a ton of codes. Urgently need your help of flashing or recoding this model. Could you help me out?
@LMAutoRepairs 6 жыл бұрын
LoL... It is funny because I have the same fault on my E65... I clear it, and it comes back some time later... I am planning to do my one somewhere this summer.... I believe you will need to code it, like VIN number etc... Flash is another story, I would say that if it came out from a car with the same amount of airbags and safety features, flash will not be required... I know you already bought a replacement, I am planning to attempt a repair on my module before move to replace it... You should have no problem in plug that one in, make sure the battery is disconnected first... Do you have the equipment to clear codes, and code the "new" module?
@gritsgong 6 жыл бұрын
lmsvvavr thanks so much for replying. Yes, the second hand module is also from another E60 M5 so I will attempt to just install it and see how it goes . I have Inpa , NCS expert, WINKFP, and tool 32. I also have ISTA/D but for some reason it won't connect(NET-0015: HOST NOT FOUND)?😣 How about restoring the SGM gateway module to factory default settings to clear the code from its memory? if yes then will these instructions work? 1 Start WinKFP and select F3:- Update ZUSB 2 Select ECU type and the ECU will appear along with a list of part numbers. 3 Select ok and the main menu will re-appear 4 Select VIN and enter the cars VIN no. and select OK. 5 Select Done 6 Select Prog. ZB_update, you will be asked to confirm the update, Winkfp wil state the number of times the module can be re-programmed. 7 Sit back and wait. 👆🏽I found this online somewhere. Or just use the second hand unit? I don't know how to code the VIN to my car if I change the module. I also installed the LM2 light module for daytime running lights and I think the VIN needs to be matched to my car as well. Will the instructions above work?
@LMAutoRepairs 6 жыл бұрын
Jermaine Hall I never performed a lot of work with kfp... When I mentioned repair, I meant hardware wise... I believe, or I hope that the problem on my one is going to be with some components inside the module... I might be wrong though... If I need to attempt to reflash it, I will be trying with ista-p or with the MaxiSys... If I was you, I would just save the original coding from your module with NCS, plug the second hand one and ensure that the common options under the coding do match the original one... BMW dash can easily change the VIN number...
@gritsgong 6 жыл бұрын
lmsvvavr ok thanks. Can you tell me how you save it with NCS? And what's BMW dash ?
@LMAutoRepairs 6 жыл бұрын
Jermaine Hall You know when you read the module with NCS and the reading is saved on a trc file? Dash is another bmw interface... Google will help you finding it... Otherwise kfp is your option to change the vin...
@Enis901 Ай бұрын
Hello! i have a question can i take any ccc unit and code it to my car? Because i bought a ccc unit from a pre lci car and the partsnumber is not the same and mine car is lci so now i get no sound haven't coded anything yet.
@LMAutoRepairs Ай бұрын
Already replied...
@Enis901 Ай бұрын
Where i cant see that?
@LMAutoRepairs Ай бұрын
On your other comment...
@Enis901 Ай бұрын
@@LMAutoRepairs Thanks i did code it today and it work so the answer for the others like me yes you can put in a ccc unit from pre lci car and yes you can take another partsnumber it doesnt need to be the same. But i have another question and that is if i can change the front panel from my old unit to the pre lci unit, beacuse the old had the touch buttons??
@joseesteves9407 3 жыл бұрын
Boa noite Luís, Poderia partilhar o link do aplicativo de alterar o VIN, não consigo encontrar no Google nenhum link para descarga! Obrigado e parabéns pelo óptimo trabalho e partilha com todos.
@LMAutoRepairs 3 жыл бұрын
O Dash 2.0 precisa do próprio cabo... Não funciona com o d-can cable... A outra opção é o winkfp... que faz part das BMW tools... Obrigado!
@joseesteves9407 3 жыл бұрын
@@LMAutoRepairs Caro Luís, tem alguma dica de como fazer o processo do video pelo winkfp? preciso colocar o vin do meu carro de E61 2005 num CIC proveniente de um carro de 2008. Melhores Cumprimentos
@LMAutoRepairs 3 жыл бұрын
É um procedimento que envolve algum risco... e tens de ter tudo instalado incluindo os ficheiros necessários para o carro em questão... difícil de explicar aqui... Eu fiz no passado com o winkfp... mas foi antes do KZfaq... e nunca gravei... Existe bastante informação de como fazer... pode não ser para o módulo que precisas, mas o procedimento é similar para qualquer módulo...
@GerlindeMeier 7 жыл бұрын
Great Video, i have change my CCC (the old one has the reboot Bug :D ), but now it dont save the bass / trebble / Fader / Balance and other settings :( i go wild XD
@LMAutoRepairs 7 жыл бұрын
GerlindeMeier Hi You need to have it coded to the car FA... in other to assume all the car specs and options...
@GerlindeMeier 7 жыл бұрын
I have to Update my CCC. Not the same software-version. Thats why it dont save the personal settings:(
@LMAutoRepairs 7 жыл бұрын
GerlindeMeier Hi Software update is not the same as coding... but you already know that. Although you might need to code the ccc first and change his vin number, prior to update the software... it all depends on which approach you are go into use .
@ress87 7 жыл бұрын
Do you have audio at all? If so, the following is probably all you have to do. You have to recode your new CCC unit to your car. There is a easy way to do this in NCS expert (much easier than the process in this video). Some background: Your car has a VO (Vechicle Order), also called FA which I think is the german translation. The VO is a string of text with information about what options your car have. For example, a car with Logic 7 has "$677" in the VO, a car with HiFi instead has "$676". Menus are missing because your new CCC is matched to a different VO. The fix is quite straight-forward: 1. Get BMW standard tools installed. This is the most difficult step, FOLLOW THE INSTRUCTIONS CAREFULLY. www.mediafire.***/folder/a7jvirbs559ib/Software ***=com 2. Get to know the software and make sure your connection to your car is good. You can do that by reading som fault codes, testing seat buckles etc. in EDIABAS. 3. Close EDIABAS and start NCS Expert. Load profile expertmode. 4. Press F1 (FG/ZCS/FA) 5. Press F3 (ZCS/FA f. ECU) 6. Select your chassis (E89=E9x) 7. Select CAS 8. Press F6 (back) 8b. Optional: Make a backup of your FSW_PSW.TRC in /WORK folder (Google it) 9. Press F4 (Process ECU) 10. Select the first module you need to code (CGATE), see explanation below 11. Press F3 (Execute job) 12. Redo step 4-9 13. Select the next module you need to code (CHOST) until all five are coded 14. Done! Your CCC is now matched to your VO (the options on your car) You still might have to change VIN etc., but this pretty much what he does the first 18 min of the video. EDIT: This process is shown @ 18:30 this video. You should do this for all modules in the CCC: CGATE, CHOST, CAUD, CTUNE, CAPPL, in that order. Then reboot the CCC (press on/off/mute-button, eject CD, eject DVD at the same time) and everything should work.
@LMAutoRepairs 7 жыл бұрын
ress87 ress87 Hi Yes I did have sound... everything worked just fine. All you have explained in your comment is exactly what I did as of 18:30 on the video... In this video I just tried to explain different ways to code the ccc... When I say the easiest way, is not the way I explain at the beginning... is the way when I actually code the ccc... Thank you for watching!
@jaycee7735 7 жыл бұрын
I need a used footwell module programmed for my 2010 X5 - can you do it for me?
@LMAutoRepairs 7 жыл бұрын
Johnny Carter Hi I would love to help... but I already have too much in my hands... Sorry for that...
@jaycee7735 7 жыл бұрын
thanks. Do you know of a way I can get this issue fixed without it costing me a fortune?
@LMAutoRepairs 7 жыл бұрын
Johnny Carter What is the issue with yours? If there is nothing with yours software related, a cheap way to do it would be either swap the MCU'S or the data on them... There is other options, but I would have to investigate... as each case can be slightly different...
@ianmatterson5632 Ай бұрын
which cable are you using/can we use for bmwdash?
@LMAutoRepairs Ай бұрын
Came with the software, I believe a dedicated interface to work with it... 👍👍👍
@ianmatterson5632 Ай бұрын
@@LMAutoRepairs that explains why my 30mins of trying to reconfig my connections and adapters failed..okay my only hope of doing this comes down to wether or not you made a further video showing the vin change with the other software you mentoned?
@LMAutoRepairs Ай бұрын
Winkfp... I started using the Autel for that, which does basically the same thing as winkfp, and never came to actually make a video for it... But I am sure there is plenty of info out there on how to do it... 👍👍👍
@ianmatterson5632 Ай бұрын
@@LMAutoRepairs i've search but could not find a utube video that deals with JUST changing the cic vin's (ANT CDMASK CDGW AND CIC APP) with winkfp..and i can't seem to buy the cable for bmwdash...
@fredblogs3871 Жыл бұрын
Hi me again lol sorry.. also can you tell me what comport to set BMW dash to some say 3 others say 1 does it make a deference?
@LMAutoRepairs Жыл бұрын
No... makes no difference really... As far as you can communicate will be fine... 👍👍👍
@fredblogs3871 Жыл бұрын
@@LMAutoRepairs thank you for your reply the reason i asked was that all other software works ie communicates with car port 1 but BMW dash does not .. might be with it being older?
@LMAutoRepairs Жыл бұрын
@@fredblogs3871 Some software does not share ports... Check under windows system with ports you have available/free and choose one of those... 👍👍👍
@mafilove07 Жыл бұрын
Same problem on E60. Are you in Uk? Thanks
@LMAutoRepairs Жыл бұрын
Yes... Do you have any tools? 👍👍👍
@mafilove07 Жыл бұрын
@@LMAutoRepairs no I don’t. I’m willing to pay and travel to you’re location.
@janimughal7180 5 жыл бұрын
Hey lm When i am going to read ccc aplication An error comes up Wrong ecu coding index And i cant read my ecu and cany do my own settings Can you help me.
@LMAutoRepairs 5 жыл бұрын
Most likely you have not set up ncs correctly... Or your SP-Daten files are incorrect for the i-level of your car... Thank you foe watching!
@janimughal7180 5 жыл бұрын
@@LMAutoRepairs how to set the i level according to my car ?
@LMAutoRepairs 5 жыл бұрын
@@janimughal7180 Jani, all that info you can find it with Google... I do appologise, but I can be here explaining you the basics... If I ever came across the opportunity, I will make a video for it... You need to read... read a lot! To understand how everything works and is set up...
@janimughal7180 5 жыл бұрын
Hey lm please tell me one last thing that when i diagnose my bmw with carly on navigation its says dvd drive is not in operation but my dvd is working ....do you think its a coding issue ?
@LMAutoRepairs 5 жыл бұрын
It might be a glitch or a bad code description on that Carly software... I bet used it, so can't really comment...
@janimughal7180 5 жыл бұрын
@@LMAutoRepairs hey man sorry to disturb u again when you go to factory reset did you uncheck the psw.man file from profile edit psw fsw ? For factory reset to appl
@LMAutoRepairs 5 жыл бұрын
@@janimughal7180 Yes... the .man file is to code the settings you change yourself...
@janimughal7180 5 жыл бұрын
@@LMAutoRepairs thnx i ll update you after doing it
@janimughal7180 5 жыл бұрын
Hey lm I tried to code my ecu to default but when i execute job its an error wrong ecu coding like .i choose right ecu e60 but i dont no why it say that and cant coding ...coapi error 200.. wrong ecu coding help me
@rampantking777 5 жыл бұрын
please help me bro, usb not reading every track on usbstick, what can i do?
@LMAutoRepairs 5 жыл бұрын
🤔 It might be a compatibility issue... try either a different USB stick, or see if there is a software update for the car... Hope that helps. Thank you for watching!
@rampantking777 5 жыл бұрын
thanks, i try to find out if there is any update but don't know how, on bmw website it is not recognize my VIN number, probably because car is old now, can you help?
@LMAutoRepairs 5 жыл бұрын
@@rampantking777 Hi You never mentioned which car we are talking about... and that didn't help... 😉
@rampantking777 5 жыл бұрын
Ohh sorry, it's 2007 e60 530d LCI
@LMAutoRepairs 5 жыл бұрын
@@rampantking777 Ok... i would try to check for updates... That will be dealer or someone with the right equipment... Hope that helps!
@Samb-ps6vk 3 жыл бұрын
Hi, I bought the dash 2.2 which came with a CD. However, nothing on the CD is in English and I cannot proceed to install. The seller is poor at support. is there a way you can assist me.
@LMAutoRepairs 3 жыл бұрын
Are you sure is 2.2? I only have the 2.0... Thank you for watching!
@Samb-ps6vk 3 жыл бұрын
LM Auto Repairs, i have 2.1.0. Can you send me a copy of your installation software
@LMAutoRepairs 3 жыл бұрын
@@Samb-ps6vk Here you have... drive.google.com/file/d/1O8LpXENhQb_0y30qW4Qhfjf2FGiXbvwp/view?usp=sharing
@Samb-ps6vk 3 жыл бұрын
LM Auto Repairs, thanks a million. I have another question, would you mind send me a mobile number and I can give you a call?
@toparapaparazzi69 6 жыл бұрын
Hello, i monted android system in my car bmw 520 E60 year 2005 CCC but i don´t have AUX input, the android work but don´t have sound on speakears, nobody in Portugal can program this.I will buy install the program and try solve the problem my question is it´s possible do that with the android system monted or the old GPS screen?
@LMAutoRepairs 6 жыл бұрын
+António Ribeiro Auxiliary on the ccc is usually not complicated to install or code... which android system are we talking about?
@toparapaparazzi69 6 жыл бұрын
8.8 "Quad Core Android 4.4 multimedia player BMW Série 5 E60 nAVIGATION gps Bluetooth Wifi
@toparapaparazzi69 6 жыл бұрын
Can you help me ?
@LMAutoRepairs 6 жыл бұрын
+António Ribeiro I can try... but as you can imagine I can't do a lot remotely...
@toparapaparazzi69 6 жыл бұрын
I see yours videos i think you are from Portugal...you have facebook or whatsApp
@kalineske2748 Жыл бұрын
I replaced my CCC and there is no sound. There is also no option for Logic7, is there a way to code that?
@LMAutoRepairs Жыл бұрын
Just code the CCC to you FA/VO... The coding will do the job... 👍👍👍
@flnvaz Жыл бұрын
I have the same issue, had to swap out the CCC in an 2009 X5 and all works except the sound. What did you use to code this?
@LMAutoRepairs Жыл бұрын
As per the video...
@raduionutmoreanu4847 7 жыл бұрын
Hi,i have a problem with my car bmw e60 06 plate.and somebody did something with ncs and messed up something and now is saying "light sistem fault"and the car on elevator is came up on dash..please give me an advice to fix it.thanks
@LMAutoRepairs 7 жыл бұрын
Radu ionut Moreanu That can be fixed by recode the car to the VO. If the coding is what is causing that problem... it might be a coincidence... Have you scanned the car?
@raduionutmoreanu4847 7 жыл бұрын
lmsvvavr thank you for your quick answer..i have tryed but im not to good in that.i was looking in your videos and i added cd changer.and also yesterday i was upgraded to ccc and the sound its not that good like before.should i code something else?cheers
@LMAutoRepairs 7 жыл бұрын
Radu ionut Moreanu Code it to the VO, providing the VO contains all the car features... If you do not know what I am saying, Google it... I have been awaiting to have one around to make a video explaining how to do it, but didn't had one yet... however might be that there is some videos for that here on KZfaq... you need to search....
@raduionutmoreanu4847 7 жыл бұрын
lmsvvavr i will do.thank you for your advice.
@raduionutmoreanu4847 7 жыл бұрын
Sorry i forgot to ask you with wich app can i change the vo?ncs?
@Samb-ps6vk 4 жыл бұрын
Hi, where can i get a good copy of bmw dash?
@LMAutoRepairs 4 жыл бұрын
It comes with the tool... Thank you for watching!
@Samb-ps6vk 4 жыл бұрын
LM Auto Repairs would you mind send me a link to source it please.
@LMAutoRepairs 4 жыл бұрын
@@Samb-ps6vk www.cardiagtool.co.uk/bmw-dash-interface-for-210-version-1639.html BUY AT YOUR OWN RISK
@Samb-ps6vk 3 жыл бұрын
Thanks, order and waiting on delivery.
@modestasandrijaitis5412 2 жыл бұрын
What cable need to use for this bmw dash software?
@LMAutoRepairs 2 жыл бұрын
For the Dash 2.0, I got the cable with the software already... For NCS, a D-Can cable will do the job... 👍👍👍
@modestasandrijaitis5412 2 жыл бұрын
@@LMAutoRepairs problem is that i need to change vin of my ccc unit and i read that d can cable wont do a job
@LMAutoRepairs 2 жыл бұрын
Will do with WinKFP... 👍👍👍
@modestasandrijaitis5412 2 жыл бұрын
Problem is with this ccc unit that when i change i idrive settings menu units to miles and mpg on my cluster its still shows kilometers and l/100km
@LMAutoRepairs 2 жыл бұрын
You need to have it programmed/coded first... 👍👍👍
@aimized1460 2 жыл бұрын
Hello LM, I have a important question for you as you know very much stuff about these things. I switched my ccc unit because it was dead, from a e90 for another one from a e60. The problem I have is the AUX is greyed out on the head unit screen and I cannot select it. Could this be because of the vin number differences ? Do you reckon if I had them matched that the aux would become selectable again ? All I want to do is just play music from my iPhone to the car speakers man thank you and god bless you
@LMAutoRepairs 2 жыл бұрын
Hi If you haven't coded the unit to your car, do that first... including the correct the vin etc... Thank you for watching and for your comment!
@aimized1460 2 жыл бұрын
@@LMAutoRepairs thank you so much for your reply brother I really appreciate the feed back. I will be matching the ccc with my carVIN within the next week or so. I will come back here and tell you wether or not it solved my issue it’s the least I can do as your videos have helped me a tremendous amount and also saved me thousands from the dealership aka ass benders. God bless you, you golden hearted human being !
@LMAutoRepairs 2 жыл бұрын
Don't just match the vin, make sure you also code it to the vo... to "tell" the unit that it is fitted onto a E90... As internally it is programmed to an E60...
@aimized1460 2 жыл бұрын
@@LMAutoRepairs ok I will try my best to accomplish this task. I’m very good at DIYs again I will come back and let you know if my issue has been fixed. Almost forgot do the HW versions matter or have any major differences my old ccc was 9.8 and this new ccc is HW 12.5 ? Once again cheers brother
@lakers-1 5 жыл бұрын
If you can code, it is time to replace OEM unit with a Pioneer double din radio in the display hole.
@sara78130 7 жыл бұрын
hi mate i got vaxuhall zafira 1.8 over heating i replace very single part just ecu left with fuse box ,,, i put diagnostc code is u0009 i dont now can u hlep me abit thanks
@LMAutoRepairs 7 жыл бұрын
Hi Overheating? The code you have is for: " CAN-Bus Node no Communication The control unit was informed by other control units, that the data it sends is not valid. Effect: The control unit doesn't take part on the bus communication" So, If the car is fitted with a cooling module, check that the code is not for that module... If it is, you might have found the problem, the only thing left will be to find the root cause... Otherwise head gasket?
@sara78130 7 жыл бұрын
hi i put notheeeer fan also i replace head gasket but sill over heating fan come on 225 and working on law speed
@LMAutoRepairs 7 жыл бұрын
KURDISTAN uk Your reply was bit confusing... Sorry... Anyway, I know this basic stuff, but, water pump? Thermostat? Air trap? Can you communicate with the cooling module, and actuate the fans?
@sara78130 7 жыл бұрын
yes i replace all even fan raditor water pump ....
@LMAutoRepairs 7 жыл бұрын
KURDISTAN uk Well... in that case I don't think I can help mutch more... you will have to investigate and figure out what you are missing... as you can imagine I can't do a lot from here... Nevertheless fell free if you have any other questions...
@TheTatoloco74 6 жыл бұрын
I need help I’m in Philadelphia i have a 2007 e61 with ccc and when i start the car I’m only getting the bmw on the screen and it never goes away they told me it needs to be recoded idk how help
@LMAutoRepairs 6 жыл бұрын
Alex Robles Hi I much doubt that is the problem... is the CCC the original from the car?
@TheTatoloco74 6 жыл бұрын
lmsvvavr yes it is the guy i bought the car from said he try to update it with a laptop and after that the radio never turn back on only thing that comes on is the bmw logo we try the 3 button reset and it turns off and back on but stays on bmw
@LMAutoRepairs 6 жыл бұрын
Alex Robles I would say you need to try to update/reflash the module... and go from there... Probably the update the previous owner tried to perform, has somehow failed, leaving the CCC inoperative... I would advise dealer or someone with the correct equipment to try to update it again...
@TheTatoloco74 6 жыл бұрын
lmsvvavr do you know anyone in Philadelphia that does that kind of work
@LMAutoRepairs 6 жыл бұрын
Alex Robles I don't even know where Philadelphia is.... Lol Just joking... I am in the UK... I would see how much the dealer wants to do a software update on the car...
@janimughal7180 5 жыл бұрын
Hey man great work I am facing error on my bmw e60 530i ..on my ccc climate control it says .wrong coding KLIMA_SG_ARTS.... could you please tell me how i fix it ? Ur reply will b appreciated
@LMAutoRepairs 5 жыл бұрын
Hi Preform the same procedure as on this video, but on the climate module... that should code it to the basic settings... Thank you for watching and for your comment!
@janimughal7180 5 жыл бұрын
@@LMAutoRepairs how to code it basic and also tell me where to get files for ccc ?
@LMAutoRepairs 5 жыл бұрын
@@janimughal7180 Jani, I suggest you to read as much as you can on the subject... there is plenty of info out there... I can't just explain you here in two sentences how to do it... it is a bit of a procedure... make sure you have bmw tools all set up and configured, along with the correct daten files for you car... You can damage stuff if you do it wrong...
@janimughal7180 5 жыл бұрын
@@LMAutoRepairs thanx but feel bad to hear u that
@LMAutoRepairs 5 жыл бұрын
@@janimughal7180 What do you mean? 🤔
@unauthorisedgangsta 6 жыл бұрын
Where are you based?
@LMAutoRepairs 6 жыл бұрын
Abid Rahman Peterborough... Thank you for watching!
@unauthorisedgangsta 6 жыл бұрын
LM Auto Repairs I have a failed ccc, keeps rebooting and bmw logo keeps coming and off, would you be able to repair?
@LMAutoRepairs 6 жыл бұрын
There is places that specialize in repair those unis, and even offer warranty! You will be better of with someone like that than with me... Usually that problem is caused by poor contacts on the BGA chips... which a reflow can easily fix the problem... I have sold my reflow machine long time ago... and reflow such big chips the old way, (With the air gun), is not a very good practice... is kinda ok for small chips, but not for the ones on the CCC... Get in touch with this guy for example... www.ebay.co.uk/itm/Bmw-Pro-CCC-E60-E63-E64-E90-E92-E81-E83-E89-E70-IDrive-Repair-Service/183286608144?hash=item2aacbbb110:g:KjQAAOSwxeBZr8j7 There is other places offering the same service, just google it... Hope that helps.
@jarrettg6634 3 жыл бұрын
I have a M-ASK system non-nav. I have a CCC unit in the mail, can anyone point me in the right direction as to how to code the CCC unit to my car from M-ASK
@LMAutoRepairs 3 жыл бұрын
Change the VO and code the car... Thank you for watching!
@jarrettg6634 3 жыл бұрын
@@LMAutoRepairs turns out I’m getting a CIC , is the coding process relatively similar?
@LMAutoRepairs 3 жыл бұрын
Yes... but there is wiring modifications needed for the cic... Is not a straight plug and play... As it is for the CCC...
@t-rexo6537 4 жыл бұрын
Die haben dein Auto falschrum zusammen gebaut !!!!
Infinity Circus
Рет қаралды 7 МЛН
Immersed
Рет қаралды 111 МЛН
E60 M5 Outlawz
Рет қаралды 13 М.
МАРТИН БОГАТЫРЕВИЧ garage
Рет қаралды 529 М.