BMW Turbo Cartridge Replacement F10 F25 F30 E84 320i 382i 528i Z4 N20 N26 2012-18

No video

BMW Turbo Cartridge Replacement F10 F25 F30 E84 320i 382i 528i Z4 N20 N26 2012-18 - Save Much Money

Рет қаралды 64,963

Күн бұрын

How to replace the turbo cartridge on BMW F10 F25 F30 E84 320i 382i 528i Z4 N20 N26 2012-2018 easy if you follow my video and save yourself a lot of money $$$$.
🛠 Large circlip pliers:
www.amazon.com...
🎦 Exhaust Manifold Turbo Removal on BMW X3 iDrive 28i N20 2.0 Engine 2011-2017
• Exhaust Manifold Turbo...
🎦 Other BMW X3 repairs:
Tricky Harness Starter Removal - BMW X1, X3, X5, 3, 4, 5 Series, N20 2011-2017
• Tricky Harness Starter...
How To Remove Spark Plug Coil Wiring Connector - BMW X1, X3, X5, 3, 4 & 5 series
• How To Remove Spark Pl...
BMW X1, X3, X5 How To Remove Spark Plug Coil Wiring Connector
• How To Remove Spark Pl...
Radiator Fan Removal on BMW X3 - Few Tools Needed
• Radiator Fan Removal o...
How to Put BMW in Neutral - 2010 & Up, Most Series
• How to Put BMW in Neut...
BMW X3 Front Axle (driving shaft), CV Joint Easier Removal - Clicking Noise When Turning
• BMW X3 Front Axle (dri...
💰Save money on your car/truck maintenance and repairs:
DIY Car Compression Test at Home - The Best Way
• Cheap Way To Check For...
Fast and Easy Way to Restore Faded Car Paint and Scratches - With Minimal Tools
• Fast and Easy Way to R...
The Best Way To Fix & Repair Broken Wire in Your Car - Soldering Car Wires Together
• The Best Way To Fix & ...
Don't let Timing Belt Failure Happen
• Don't let Timing Belt ...
Look what happens when you neglect your engine oil
• Check and Change Your ...
How to diagnose and replace wheel bearing going bad on any car
• Whining, Grinding Nois...
Check your Engine, Coolant, Transmission, Power Steering Fluid, and Brake Fluids
• Check Your Car Fluid L...
Learn 3 Symptoms of Blown Head Gasket
• Learn 3 Symptoms of Bl...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

Пікірлер: 142

@ES-iv6wb Жыл бұрын

This video is super underrated! Easily explained by a pro. Thank you 🙏🏼

@Motorcarnut Жыл бұрын

Thank you very much for your kind words!

@TerrybleGamer 2 жыл бұрын

At 3:49 you said that these valves are not common to fail. If I might add, they certainly are. So much so that a lawsuit was started because of this problem, demanding that the engine be replaced under warranty and/or the waste gate had to be repaired. Other than that, I find the video informative and easy to follow. Thank you :)

@Motorcarnut 2 жыл бұрын

Thank you for bringing that to my attention, I was not aware of that. Maybe someone could benefit from this information.

@haydenmurphy9211 Жыл бұрын

Where can I find this info, I’m currently having this problem and keep getting forms for wastegate rattle but that’s not the problem I’m having the flap itself went bad

@Motorcarnut Жыл бұрын

I’m working on a video right now that should be done soon about how to replace the waste gate flap for good.

@nazeer3495 Жыл бұрын

you a magician im currently doing one on a n20 thank to you and i saved alot of $$

@Motorcarnut Жыл бұрын

Lol, thanks for the comment I really appreciate it!

@tyler951 2 жыл бұрын

Excellent stuff. Really doesn't look bad... after you get the turbo out.

@Motorcarnut 2 жыл бұрын

Thanks, Yes its not.

@tyler951 2 жыл бұрын

@@Motorcarnut Here is mine, did a 3 month 2,000 mile check up and clean up on my leak. Not getting any worse from what I can tell. This is a N55B30A on my 2017 X3 xDrive35i with only 40K miles. Not seeing any oil burning from the exhaust or smelling it. Probably going to have to eventually replace the cartridge aren't I? kzfaq.info/get/bejne/epaHYMJmscuuo4E.html

@Motorcarnut 2 жыл бұрын

No, not necessarily. If the cartridge was leaking from the turbine seals you would be blowing blue smoke out the tailpipe. The only place it could leak oil in that area is from the oil feed tube o ring that goes into the cartridge and they are know to fail.

@danielc5436 16 күн бұрын

Thanks 🙏 for the great vid sir! The turbo in my F30 has just failed at 300,000km and I think this might be the solution for me as well. However, before I make my purchase, I just wanted to know if you’ve felt any power loss after installing the new one. 🙏

@Motorcarnut 15 күн бұрын

Sure no problem! No, if anything even more power because it’s brand new new.

@erickcontreras9322 4 ай бұрын

Amazing video. Well explained👌🏽 It would be nice if you posted links for the parts you used. But then again i might be asking for too much already... thank you for the knowledge 🫡

@Motorcarnut 4 ай бұрын

Thank you for the feedback! You can get the parts on EBay or Amazon with your year make and model.

@raymondresendiz2202 6 ай бұрын

Thank you so much! Very well explained

@Motorcarnut 6 ай бұрын

You're very welcome!

@dinhvanpham8102 Жыл бұрын

Thank you for a fantastic tutorial video. I have a damaged turbo which was taken out of my car BMW 525D F11 2012 xdrive with a N47T engine. Can you please tell me where to buy a new Turbo Cartridge? I want to repair my old turbo.

@Motorcarnut Жыл бұрын

Thanks for the comment! Yes, you can look on eBay they are good quality ones there.

@hotbutterypopcorn9652 Ай бұрын

Would you have any ideas on how to fix a turbo leaking oil? My repair sheet from bmw says that its a turbo fix/rebuild for wastegate outside tolerance. Is it the seals? Will replacing the entire turbo fix it? Or a new wastegate actuator? Id rather buy what i need amd fix it myself rather than paying six grand for bmw to fix the issue. 2013 bmw 328i x drive...any info would help 😊 Thank you for all that you do!

@Motorcarnut Ай бұрын

Thank you! Appreciated. The cartridge replacement will fix your problem.

@gussusancabezas3990 2 жыл бұрын

Excellent video for the turbine replacement. What is the other video that shows how you remove the housing?

@Motorcarnut 2 жыл бұрын

Exhaust Manifold Turbo Removal on BMW X3 iDrive 28i N20 2.0 Engine 2011-2017 kzfaq.info/get/bejne/pp-IldmZrbWzln0.html

@musclefactory9181 Жыл бұрын

I’ve got a couple options for installation that I wanted to run by you and see what you think? Option #1 install coolant pipe and oil pipe into engine block below the header before installing the exhaust manifold? Option #2 install exhaust manifold, firstly, and then the pipes if clearance will allow it? Option #3 fit the Turbo cartridge into the turbo housing after option #2 ? Option #4 Assemble the Exhaust Manifold and marry the cartridge to the turbo housing and carefully bring it into positioning with the studs, considering option #1 Bro I’m asking you this because it gave me annoying Turbo dreams 😂 I literally couldn’t sleep.

@Motorcarnut Жыл бұрын

Option A, depending on your model and year. Assuming engine is still in the car.

@Bond786muslim 15 күн бұрын

Whats the cause on a whining sound in the engine when the engine heats up? But the car running normal.

@Motorcarnut 15 күн бұрын

Too vague of a question? But more specific

@cxexzzz3662 2 ай бұрын

My turbo has definitely gone bad but I’m not getting any codes, my car has had a huge loss in power in low end rpm, it’s like I’m not getting boost at all til around 5-6k rpm. And my turbo spool Is super loud for no reason

@Motorcarnut 2 ай бұрын

Turbo sounds like it gone

@Bond786muslim 15 күн бұрын

How do you know ur turbo is not working?

@Motorcarnut 15 күн бұрын

In a BWW you will get all kinds of turbo related codes for one and vehicle will have no power or boost as it did before

@musthakahamad 10 ай бұрын

this is very good video , but can u show us how to remove the turbo and from car.. that should be helpful

@Motorcarnut 10 ай бұрын

Ok next time one comes in.

@crowdsfavorite4660 Ай бұрын

Do you have a link for the n55? I have a x3 f25 n55 can’t find a cartridge kit for it

@Motorcarnut Ай бұрын

I don’t off hand, try eBay

@Tony-jv5pr 3 ай бұрын

Nice video, I'm wondering whats the nm of the tighting.

@Motorcarnut 3 ай бұрын

Have to look up your particular vehicle , they are different from year to year and model

@Zrmotors 4 ай бұрын

Thank you great educational video

@Motorcarnut 4 ай бұрын

Glad you enjoyed it! Appreciated.

@census3370 Жыл бұрын

My turbo is shot I’m praying it’s like this. Where can I find the piece you replaced!! Great vid!

@Motorcarnut Жыл бұрын

Thank you!, On eBay, some sell rebuilt OEM ones.

@boomy818 Жыл бұрын

You can do this, but the wastegate valves are a common failure item on these cars, and if your doing just the cartridge its only a matter of time until you have to replace everything due to bad wastegates

@Motorcarnut Жыл бұрын

This is true. That’s why I have videos on replacing the flapper wastegate valve as well.

@edwardannobil7908 2 жыл бұрын

Can you give a link for the turbo cartridge ?

@Motorcarnut 2 жыл бұрын

www.ebay.com/itm/324708153060?fits=Make%3ABMW&hash=item4b9a1d36e4:g:4HgAAOSw091c5RJh

@erer9961 Жыл бұрын

Outstanding video, i want to know where did you get this Cartridge for the N20 TURBO?

@Motorcarnut Жыл бұрын

You can look on ebay

@baims8367 11 ай бұрын

Where did u buy the replacement turbines for $250. I must of missed where u said u got it .. thanks for the info

@Motorcarnut 11 ай бұрын

Depends on what you want? Aftermarket or OEM. EBay has both. Just type in your vehicle info.

@zanastumasonis 4 ай бұрын

can oil leak out the turbo besides from the oil feed and return orings? can it leak straight out the turbo somehow?

@Motorcarnut 4 ай бұрын

Yes, and cause oil burning

@dinhvanpham8102 Жыл бұрын

Hello, I appreciate a lot your sharing o\f knowledge. I had a turbo crash. The workshop replaced a new turbocharger. After that my car acts lik in limbo with no boost at all. I ran a diagnostic and it confirm my booster pressure solenoid was defective. I replaced a new one and all errors disappear except error 29A400 saying charging pressure actuator position control. charging pressure actuator closed too far/positive deviation. My rode is a long plastic going from the wastegate to the turbocharger locked by a c-clips. Please help me. I need to make a crack pressure and adjust the wastgate properly.

@Motorcarnut Жыл бұрын

This has to be adjusted with a scan tool, do you have one?

@dinhvanpham8102 Жыл бұрын

@@Motorcarnut I have a scan tool. I have watched many videos at KZfaq where several recommend a Mityvac hand pump vacuum/pressure in order to find and adjust the crack pressure point. Have you used a hand pump to adjust the wastegate?

@user-nh8td2hr1x 2 жыл бұрын

Hello I am about to change my turbo on my f30 .i can see oil leaks from turbo but I do not have power loss yet . Is it possible to be something else than turbo failure ?

@Motorcarnut 2 жыл бұрын

The turbo has oil and coolant flowing through the bearing to keep it lubricated and cool. Could be one of the gaskets or oil rings connected to the turbo unit.

@brokentobuilt Жыл бұрын

Its entirely possible to have a failing turbo without any noticeable power loss

@advxnturxwithmx Жыл бұрын

doing this on my n20 this week. Do you need a new charge pipe hose/clamp when doing this job?

@Motorcarnut Жыл бұрын

@DJSmacks201 2 жыл бұрын

I need to do the same exact think!!!!

@Motorcarnut 2 жыл бұрын

Go for it, makes the car run like new again

@DJSmacks201 2 жыл бұрын

@@Motorcarnut getting a whining noise when I hit the accelerator!! I narrowed it down to find out it was the turbo!! Just want to know if this is definitely the solution!!! And we’re u getting the drivetrain malfunction?

@Motorcarnut 2 жыл бұрын

Can’t say for definite, because I’m not there diagnosing it but yes it was throwing codes and burning oil

@YTKushSmoke Жыл бұрын

My 328i 2013 has 80k mls. Mine is throwing code P1290. Mechanic scanned it and said something about the waste gate. I’m waiting for a diagnostic on Wednesday. I only get drivetrain malfunction if I do a hard pull and kill engine and don’t give it time to clear code (5mins) before starting up again

@Motorcarnut Жыл бұрын

Wastegate actuators are a common failure on these cars, it's probably that.

@YTKushSmoke Жыл бұрын

@@Motorcarnut So my best bet is to replace just the actuator first, before I get told “you need a new turbo” by the mechanic? Right? Would it hurt to swap the actuator with a new one even if that wasnt the problem to begin with? Would I have to code it or something? This is my daily driver, so whatever it is, i plan on getting it repaired. Thanks for the fast response. I really appreciate the info

@Motorcarnut Жыл бұрын

Yes, and they do have to be reprogrammed with a scanner.

@Xanadu98 Жыл бұрын

@@Motorcarnut if I get a new turbo with a electronic actuator do I still need to reprogram it or will it just be plug in play

@Motorcarnut Жыл бұрын

The electronic one may have to be reprogrammed. You can replace it and see if you get boost codes, if not you’re good to go.

@user-rq5hj8hr3e 8 ай бұрын

Just wanted to know if the water to runs out of my exhaust system look like it runs through the turbo charger bmw 318i 2016 model

@Motorcarnut 8 ай бұрын

The water you see out of the exhaust is normal condensation. Coolant runs throught the turbo to cool it off.

@davidcollison8490 Жыл бұрын

Great video

@Motorcarnut Жыл бұрын

Thank you, much appreciated!

@Sipho-Msayi 2 жыл бұрын

Great video, thanks

@Motorcarnut 2 жыл бұрын

Thank you!

@zacharysuttle6753 7 ай бұрын

Please tell me , on the cars youve done these CHRAS on hopefully n54 how long have u seen these after market ones going for ? Like miles an hm. Im about to replace mine with svt its a 6+6 high flow , its got a 9 blade turbine on the other side rather than 11

@Motorcarnut 7 ай бұрын

Can't say how long but did many of these and never had one come back.

@jonathanrealestate Жыл бұрын

Disconnecting the cartridge off the turbo has been a huge bump in the road. Did yours just come apart easily?

@Motorcarnut Жыл бұрын

Yes, spray some penetrating oil first then try giving it a few taps, there is a pin for alignment and sometimes they get hung up there

@jojomosgo 2 ай бұрын

for the one's on Ebay, do you have any perspective if the $230 upgraded unit is a better choice than the $100 normal unit?

@Motorcarnut 2 ай бұрын

I don’t know which ones you are referring too?

@jojomosgo 2 ай бұрын

@@Motorcarnut items 203716228612 and 353394217332. I think these are all Chinese. I was hoping to find a German one

@AlvaroRamon998 2 жыл бұрын

Hello I was doing the same procedure and I notice you place the compressor lock ring in wrong position at 8:25, I made the same mistake, the Ohm lock has one side with some angle on the edges....

@Motorcarnut 2 жыл бұрын

The bevelled edge faces up on the snap ring, it’s hard to see it in the video.

@bennybeeeee 2 жыл бұрын

Thanks man

@Motorcarnut 2 жыл бұрын

You're welcome!

@lucasramushu8522 Жыл бұрын

Hey, if it's burning oil, does it also reduce coolant or burn it? Please help

@Motorcarnut Жыл бұрын

You mean the turbo cartridge? It could because it’s water and oil cooled.

@mczacify Жыл бұрын

Is it possible to replace just the wastegate for f10 2012 n20 bro?

@Motorcarnut Жыл бұрын

Yes, 2 bolts and the arm clip and it comes off

@GP-007 6 ай бұрын

On my b47 engine 190 hp , work that operation?

@Motorcarnut 6 ай бұрын

Yes

@GuillermoHernandez-br8gl 8 ай бұрын

Excelent

@Motorcarnut 8 ай бұрын

Thank you!

@Velezl209 Жыл бұрын

I'm looking to do my turbo. But I'm hesitant about the quality of the cartridge can you provide any updates on how it's aged and If you've had any issues come up with it?

@Motorcarnut Жыл бұрын

I’d recommend a high quality OEM unit if possible.

@Velezl209 Жыл бұрын

@@Motorcarnut any notable issues?

@Motorcarnut Жыл бұрын

As far as what? With a high quality one , no issues the cheap ones are fine but don’t know the longevity of those so far

@Slowww_F30 7 ай бұрын

Will this work on a blown turbo?

@Motorcarnut 7 ай бұрын

Yes, that’s what it repairs

@phil_aesthetics Жыл бұрын

Is it possible to get a cartridge for the N55 turbo as well?

@Motorcarnut Жыл бұрын

Yes, search eBay if you want an affordable one

@geovannycarrion6221 2 жыл бұрын

Where do you get it from I'm having that problem right now can you please send me the information to get it

@Motorcarnut 2 жыл бұрын

www.ebay.com/itm/Turbo-Cartridge-CHRA-for-2011-17-BMW-320i-328i-520i-528i-X1-X3-Z4-N20B20-2-0L-/324708153060?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0

@my4cavs Жыл бұрын

Is this applicable to the x1? BMW replaced my engine a year ago, (due to a mechanic not repairing correctly) now they are telling me I need to replace the turbo charg.

@Motorcarnut Жыл бұрын

I don't know your year but if it's a 4 cylinder, yes

@my4cavs Жыл бұрын

Thank you, sorry it is a 2015. I did find the name, cartridge,thank you again. Great information! Great video.

@Motorcarnut Жыл бұрын

Ok, thank you for the comment

@Patcha2003 Жыл бұрын

Ok but where’s the video about where it’s located cause I can’t find anything

@Motorcarnut Жыл бұрын

You don’t know where the turbo is on your car?

@jamesmccallion4526 Жыл бұрын

Anyone know a reputable cartrage replacement for n55 engine

@Motorcarnut Жыл бұрын

Try eBay, there are sellers on there that remanufacture the OEM units.

@derekkchung 10 ай бұрын

Wastegate rattle is the number one problem. U need to know / learn how to weld. If the cartridge is out and if the blades are in good condition, mind as well rebuild it for $30 parts than couple hundreds $ to replace the cartridge.

@Motorcarnut 10 ай бұрын

Definitely, one of the reasons, have a video on that one too: kzfaq.info/get/bejne/bMtmqK5618ecgpc.html

@callumleeson1238 Жыл бұрын

Do you have to balance it?

@Motorcarnut Жыл бұрын

No, they come balanced.

@FranklinChang 2 жыл бұрын

Where did you buy that turbine part? part code?

@Motorcarnut 2 жыл бұрын

Just look on ebay with you year make and model and engine code and you'll find them around $200 shipped

@my4cavs Жыл бұрын

WHat is that part called, turbine?

@Motorcarnut Жыл бұрын

Turbo Cartridge

@generralugenerralu5987 Жыл бұрын

Donde puedo comprar esta piesa ? Gracias

@Motorcarnut Жыл бұрын

EBay, just search : BMW n20 turbo cartridge

@generralugenerralu5987 Жыл бұрын

Gracias. Muy útil este video. Intentaré cambiar esa piesa yo mismo ya que tengo conocimiento de automecanica. Algún concejo en especial además del video?

@Motorcarnut Жыл бұрын

You're welcome. Besides hand tools you will need a big snap ring pliers like in the video. Just take your time you should be fine.

@mayakaahla991 Жыл бұрын

Is this called the “impeller” ?

@Motorcarnut Жыл бұрын

It’s called the turbo cartridge