bodgit and leggit garage tips and tricks inside your video hopefully help you don't forget get your hands dirty this video look at how to wire up electrics on a car
Пікірлер: 168
@ben2e0omr2 жыл бұрын
I think you have just saved me around £400.Thank you bodgit!!!
@jap38622 жыл бұрын
I'm a bricklayer and I managed to get my head around the relay bypass kit successfully wired in with help from bodgit and leggit thanks bro!
@chrisvandenbosch16606 жыл бұрын
Followed Bodgits advice and successfully wired in my trailer electrics.. a proud moment as I usually struggle with wiring a domestic plug. Thanks for taking time to film the video Bodge..! first class..!
@bodgitandleggitgarage6 жыл бұрын
chris van den bosch thanks mate and congratulations well done I'm glad my videos are helping people that's what it's all about
@martynhart78237 жыл бұрын
Thanks for this vid. Great - no shaky camera and comprehensive detail put over in a pleasant way.
@bodgitandleggitgarage7 жыл бұрын
Martyn Hart thanks a lot mate much appreciated lot of work goes into my videos and nice to know people appreciate then
@joregan754 жыл бұрын
You just helped me pass my NCT , rear fog light would not work on car , checked the wiring for the towbar and there it was the sctochlock that was holding the cars blue wire to the towbar blue wire had broke and all the wires were hanging lose so I left the towbar blue wire off and reconnected the cars fog light blue wire , and bingo the car fog light worked again . I just wont use the fog light when towing a trailer, the rare times I actually tow the trailer . Great video thank you .
@wickhamdecks82987 жыл бұрын
I'm in Australia, good info and the audio is great. Pretty sure these same steps apply here, will make sure I return and watch this again when I do my tow bar build.
@bodgitandleggitgarage7 жыл бұрын
Wickham Decks ManuPro hi mate thanks a lot for watching it should be the same but I'm not 100% they might be some little differences but if they are they should only be small
@garrygemmell56762 жыл бұрын
Best explanation on youtube super simple no BS!
@MrWhichword10 күн бұрын
Very helpful. Thank you.
@Garibaldi07144 жыл бұрын
I did mine yesterday and was easy following your expert knowledge. Many thanks. 👍
@bodgitandleggitgarage4 жыл бұрын
Boom sorted I'm glad that video helped you mate
@lukemannion2988 Жыл бұрын
Just after fitting a towbar and needed help with wiring great video best one out there thank you for your help keep up the good work.
@bodgitandleggitgarage Жыл бұрын
Glad you enjoyed it glad it helped you that's what these videos are all about
@lukey35075 жыл бұрын
This video was useful for me, thanks Leon. Very informative and easy to follow :-)
@bodgitandleggitgarage5 жыл бұрын
Glad you enjoyed it mate that's what it's all about
@francesbrowne73782 жыл бұрын
you make it look so easy but I think I will take it back to garage when I get the canbus for my Jeep Renegade but this video its great just to check if you need a canbus or not thank you so much you explane is so well
@colauty25985 жыл бұрын
cheers, simple instruction, common sense required , Excellent !
@bodgitandleggitgarage5 жыл бұрын
thanks mate
@rikgraf7 жыл бұрын
Thanks for a great video extremely well explained and clear
@bodgitandleggitgarage7 жыл бұрын
thanks mate
@robertkennaugh20573 жыл бұрын
Thanks so much you really helped me for my car
@simonsas14925 жыл бұрын
Very helpful, thank you.
@Jovis88882 жыл бұрын
Doesn't help me because my issue isn't addressed but I really enjoy these presentations. Thank you. Good stuff.
@timnathan82863 жыл бұрын
It's good to gain the insight of what's required.
@johnwall88417 жыл бұрын
I have wired and fitted 6 towbars and about to fit another, working out the wiring has been a nightmare, you make it easy understanding the testing of the wiring socket, testers are on the way. Thanks
@bodgitandleggitgarage7 жыл бұрын
thanks mate
@steffiradbourne7662 жыл бұрын
Thanks got my caravan sorted
@bilimanjaro3 жыл бұрын
very well explained.thanks.
@habibisakhi24504 жыл бұрын
Excellent work mate and very clean explication
@bodgitandleggitgarage4 жыл бұрын
Glad you enjoyed it
@goshhowhorrible83404 жыл бұрын
Thanks. Great video
@josephmuscat95726 жыл бұрын
Well done - very well explained
@bodgitandleggitgarage6 жыл бұрын
thx mate
@petercze30673 жыл бұрын
Thank you very much. It was very helpful. (:
@alibunford5 жыл бұрын
super good video. thanks
@wordavy5 жыл бұрын
thanks i was having the problem of more than 1 wire giving a reading followed your instruction jobs a goodun cheers
@bodgitandleggitgarage5 жыл бұрын
I'm glad it helped you out mate thanks for watching
@jamesplews32135 жыл бұрын
brilliant very clear, thank you.
@bodgitandleggitgarage5 жыл бұрын
thanks mate
@gee38834 жыл бұрын
Nice one matey. I am currently stuck in the middle of nowhere in eastern Europe and need to fit a tow bar to an old Audi your vids a huge help, top man.
@bodgitandleggitgarage4 жыл бұрын
I'm glad the video helped you mate I hope you got out of trouble
@gee38834 жыл бұрын
@@bodgitandleggitgarage I managed to get the tow bar fitted after a bit of a fight ,I didn't realise when I bought it that it has had a whack and was slightly out of line making all the bolts not line up. Wiring it 2 moz as I couldn't get the cable etc fingers crossed thanks again mate, saved me a few quid.
@bodgitandleggitgarage4 жыл бұрын
@@gee3883 I'm glad you got sorted and I'm glad my video Help mate all the best
@125sm35 жыл бұрын
Thanks for the video Leon
@bodgitandleggitgarage5 жыл бұрын
thanks mate
@DanielMarshUK7 жыл бұрын
Thanks for posting this... the Skoda main dealer told me that you can't do a home fit for a tow-bar and electrics but I fitted one to a Fabia Estate today and followed your guidance for the wiring. All works fine except one weird anomaly where if the main lights are on they switch off rather than get brighter when I break. When the main lights are off the brakes work as expected... not going to sweat it but will avoid driving at night instead ;-)
@bodgitandleggitgarage7 жыл бұрын
Daniel Marsh hi mate that is certainly unusual make sure you've got a good Earth and you are not back feeding through something also make sure you've got a good power direct from the battery and just make sure you have the correct box for your car
@jasonmatthewson85346 жыл бұрын
Many VAG cars overload protection and will cut the power to the bulb if it thinks there is too much power going to it. Any VW, Audi, Skoda or Seat after about 2004 should have a bypass relay ("Box") put in regardless of whether it has led lights or not. A lot of them run a dual voltage single filament bulb for the side & brake lights, which bypass relays can decipher the signal for and apply the correct lights on your trailer.
@napper14962 жыл бұрын
It’s because some cars will throw a wobbly due to canbus
@martintraynor60714 жыл бұрын
Brilliant video . Have you ever put trailer lights on a Peugeot Partner Van struggling having difficulty with the Break light and haven't even got the indicators Thanks
@shifty27553 жыл бұрын
You also need a TEB relay if your car has a bulb failure system. It takes the load off the circuit when your trailer is connected.
@jackthelad-ou6zu6 жыл бұрын
hi just a word in your ear this saying has bin going around for a very long time but we from Liverpool say it like this BODGUP-AND-LEGGIT just saying and thanks for the vid
@terryplatts28444 жыл бұрын
cheers mate good video - especially the "can" bit -i think my old bus doesnt have can so you will have saved me a few quid - also the tip about bigger fuse- its those little things that can catch people like me out , ill have a go at this -cheers....... around here we always used the term bodgit and scarper lol
@bodgitandleggitgarage4 жыл бұрын
lol thanks mate
@terryplatts28444 жыл бұрын
@@bodgitandleggitgarage - , just fitted one today,including indicator bleeper, i doubt i would have had a go without your video - total cost £11.99 and a couple of hours or so to fit ..... thanks again really appreciated.
@arkaywat117 жыл бұрын
Thanks for the vids. I've just wired a 2006 peugeot 206 SW tow bar and then I wondered if it may be "can bus" wired. Is there an easy way to tell. Everything works fine but I'm worried something may get damaged after prolonged use. Thanks!
@bobdelaplage6903 жыл бұрын
I film the rear of my trailer, when im alone....review it, and ...sorted....or when i have to go to M.OT....also carbrakes light and rear backuplichts( the white ones)are easy to test that way...💪hope this helped...as a return....Bob Belgium thanks brother!
@coloradoblues2 жыл бұрын
Very good , thank you . I'd like to ask if there is the possibility to feed the box from that 12 v socket inside the boot , if would be possible is it also fused already . Meaning could be a plausible alternative ?
@jamescavanagh92762 жыл бұрын
Great Video. You clearly care about your customers. Is the indicator buzzer you mentioned audible outside the car?
@Dekon19852 жыл бұрын
Great video thank you so much I would like to connect the fog light from the tail gate, it be would very useful if you show this to people in an other video Thank you
@alanbowen5754 жыл бұрын
Brill clear video Any chance you can do 13 pin electrics on a Navara D40 Cheers Keep up the good work
@ashbrauw4 жыл бұрын
thanks buddy, if we ever come across i'll buy you a drink 👍
@bodgitandleggitgarage4 жыл бұрын
Anytime mate glad my videos help. That's what they're all about.
@raycollins41492 жыл бұрын
Hi great video. I'm trying to wire a bypass into my 2013 mondeo and I brought the wire in from the right side. Does this matter. As in what side you splice of from. Thanks Ray
@habibisakhi24504 жыл бұрын
Would you able to tell me where to buy that tester please? Any brand name or other to use please. For car without led and 2007 car do I still need that box or no? Many thanks
@dymo992 жыл бұрын
Hello Bodgit, can you do a video on wiring up a single tow bar electrics with Can Bus wiring. Many Thanks
@TheM6aae8 жыл бұрын
Where did you get your tester from? what's the make please?
@anthonyhandsley23013 жыл бұрын
good video .but looking on you tube ,nobody shows how to install a trailer buzzer . could you please do a video on how to install a trailer indicator buzzer
@MrGentleNick6 жыл бұрын
Yes, I do not like Scotch grips either, and like you, use solder or crimp plus and sockets and heat shrink (remember to put in place first) and pipe pliers are better more often than not
@bobdelaplage690 Жыл бұрын
Thx brother, so you just make T connections on the existing wiring ?
@simonrawle78857 жыл бұрын
this is one of the few jobs il pay someone to do
@swedishkev5 жыл бұрын
Hi there mate, I hope you can help me. I have an Xsara Picasso from 05 ,It is muliplex,canbus. I have fitted the towbar and now need to do the wiring. The 7 pin wiring is 2 harnesses. One with 4 wires and the other with 3 wires . This towbar and wires are for a Picasso. Why are they split up like this ? I have a by-pass relay and I can see I have to screw all the wires into the relay. But then I am confused ,can it all be wired to the left side of the lights or how do I know if I have to wire in on both sides ?. The left side is 8 wires going to the backlight and the right side is 6 wires. Lets just say you explain to me that I need to wire both sides, Do I then lets say the red is the lights on wire and I need to connect this to the red on the relay. Do I need to add an extra wire there and take it over to the red on the other side. ? Also the colours on both sides are a little diffent. Appreciate your help. I have tried registering on the Citroen Picasso owners club for over a week .something really wrong with their site. All the info is there and I can not get to it, very frustrating.
@tommyh8185 жыл бұрын
Will a bmw 120d 2005 have can bus wiring
@roadrunner86675 жыл бұрын
Do i need one of those boxes for a 2006 passat 1.9tdi b6 ?
@craigwilson777 Жыл бұрын
The connections your using are pish m8 they give you norhing but hassle thanks for the video
@wingwong3984 жыл бұрын
Hi after you done the left indicater where does the green wire go on the other indicator I tried putting the green wire on the other side but it won’t work everything else does
@michaelhurley27218 жыл бұрын
Thanks for the video. Our merc is 2003 (no led) so I can wire BOG STANDARDLY? only there is a switch on the merc dash that is for towing
@jasonmatthewson85346 жыл бұрын
Even though mercs have standard bulbs they still need the bypass relay ("Box") they have very sensitive bulb failure systems. Any switches and bulbs on the dash for towing will only be activated with a dedicated wiring kit & re programming the car.
@martinreid78997 жыл бұрын
Thanks for the videos - been trying to source a canbus compliant 12v voltage tester unsuccessfully - any you can recommend? - Cheers, Martin.
@bodgitandleggitgarage7 жыл бұрын
Martin Reid hi mate all I can really do is tell you the ones I use this is the videos to the ones I have got kzfaq.info/get/bejne/bLWYepp4rJfKko0.html
@bobdelaplage6903 жыл бұрын
Bigger fuze, nice info....+ 5 v ?
@billywhizz986 жыл бұрын
Brilliant tutorial what is the circuit tester you are using and where can you buy it from I have one but not as good as that shows you the voltage
@bodgitandleggitgarage6 жыл бұрын
william walker hi mate they're not available anymore as far as I know maybe eBay would be your best bet if one comes up
@charandass32284 жыл бұрын
Hi thanks for your video it’s very helpful I have bmw 320d e90 2011 model how I can find out it’s Camber wire or normal wire thanks
@bodgitandleggitgarage4 жыл бұрын
Hi mate I've done full video series on exactly what to do and the equipment you need to do this job I explained everything in the video
@diesalweasel6 жыл бұрын
Hi thank you for your video at the video 1 min .what the make and model of your tester which is can bus compatible. Best regards james
@bodgitandleggitgarage6 жыл бұрын
James Birkin hi mate the one I was using in this video was a Sykes pickavant Terminator
@AndyK.15 жыл бұрын
A lot of cars will have a spare connector in the back where a factory option tow bar plugs in. So it is worth having a look for a spare connector along the rear. It makes the job easier and doesn’t overload the cars wiring.
@mrcaboosevg60895 жыл бұрын
If they're cars likely to be used for it, hatchbacks like this aren't gonna have on
@lukejones12443 жыл бұрын
Would that be in the light?
@AndyK.13 жыл бұрын
@@lukejones1244 No. it gonna be where a tow wire can enter the car thru grommet and plug in. or Maybe on one side of the car.
@NickBowmanYewTewb7 жыл бұрын
This video is great, I was verging on the terrified looking at the wiring kit / instructions I got from Halfords. If you get a chance to look at the one remaining question I have left...from this video it seems like I won't need the bypass relay supplied, instead I should just directly connect the wires without it (guessing the bypass relay is only needed for can bus wiring)? Whether you get a chance to reply or not - thanks a lot for doing the video.
@bodgitandleggitgarage7 жыл бұрын
Nick Bowman hi mate this video is for car without canbus I will send you the link to a video I did with a car with can bus wiring it's very important you know what your car is you can cause a lot of damage if you get this wrong thanks a lot for watching kzfaq.info/get/bejne/jpdjislkkrXNpY0.html
@NickBowmanYewTewb7 жыл бұрын
Mine is a 2004 Mazda without LEDs so I guess without can bus (I will verify before I do anything!)
@lukejones12442 жыл бұрын
How do you test which cable into the light is the Earth?
@betterlivindserv96058 жыл бұрын
hi Bud nice video need your help, I have a Bmw 1 series 5dr hatch back E87 05 Plate and i want to know how to do a dedicated wiring kit, I've had a look online, i thought a dedicated wiring kit would mean i don't have to cut wires and just plug it in is this the case or not, costs £140 so i don't want to risk cutting cables , if i have to do this anyway i will put in a relay and do it myself.
@bodgitandleggitgarage8 жыл бұрын
hi mate as far as I know it all depends on the kits you bye I have not done one this way myself on a BMW I had a quick look at a couple of kits and it looks like they are just plug and play but I cannot be 100% certain I know for certain things you can buy both a plug and play one and one you have to wire in yourself what I suggest you do is email the person you are buying the kit off I know I haven't really help you with this question I'm sorry but I have not done one this way myself let me know how you get on thanks
@davidguest60046 жыл бұрын
I have a new shape Vauxhall Vivaro 2014 1.6 CTDI. I’m stuck wiring my 7 pin connector up to the vans wiring. Not sure if it’s standard wiring or cam bus.
@bodgitandleggitgarage6 жыл бұрын
David Porter hi mate the easiest thing to do is go to somewhere that sells the tow bars and buy a kit for your car they will give you everything you need for your make and model it saves all the guests work
@neilcurrie33864 жыл бұрын
Just watched your video, can I please ask if you know if I would be able to wire up a towbar the same way on a 1987 Mercedes 190e 2.6 ( having to use secondhand towbar, new ones are pretty much obsolete now....). Do you have to have audible signals by law for mot. Cheers
@bodgitandleggitgarage4 жыл бұрын
Hi mate with the vehicle that old you can just worried him normally with no problems whatsoever as long as you use brand new bolts with a second-hand one you will not have any problems
@v0rtex7617 жыл бұрын
hei, when all wires are connected like this, is there no shortage of electric power for the light bulbs? and wont the wires get burnt since some wires will support twice as much bulbs than before, if not more for some... regards Dovis btw easy explanation, thanks for the video
@bigdorkification7 жыл бұрын
Dovydas Tyrius hes wiring them in parallel so the current will increase to support the tow bar lights. The circuit with factory wiring will be more than capable of handling it. He did advise that a higher amp fuse is installed but isnt really needed. The fuse is mainly to protect against a short circuit.
@theinnocentbuda7 жыл бұрын
hello I just fitted my towbar to my "corsa c 2004" and now i dont know if it has canbus wiring. can you help me find out if it has it or not? thanks and keep up the good work. :)
@terryrich42853 жыл бұрын
Well if it makes you feel better I'm about to hard wire my 2007 corsa d and take the chance lol
@gerrybongo6 жыл бұрын
Can anyone tell me where to buy a can bus compatible tester please ? . Great vid and helped me loads thanks bodgit and leggit
@bodgitandleggitgarage6 жыл бұрын
gerrybongo hi mate any good quality one will do you find there's lots of really good second-hand ones out there on eBay and things like that
@gerrybongo6 жыл бұрын
can you recommend one that's safe on newer cars , or what it needs to be able to test . searching eb#y but nothing jumps out .
@alphajoint7 жыл бұрын
don't you have to also wire in a 12v supply to the relay? or did I miss that bit?
@bodgitandleggitgarage7 жыл бұрын
Antony Williams no don't need to do anything like that on this particular car with a car with canbus wiring you have to put 12 volts to the box but not on this model
@andygray37865 жыл бұрын
Great video. Thankyou Shame you weren’t fitting the buzzer too
@bodgitandleggitgarage5 жыл бұрын
Buzzer?
@andrewgallagher87568 жыл бұрын
hi mate great vids! whats the probe you are using to test the wires have electric?? thanks
@bodgitandleggitgarage8 жыл бұрын
hi mate i am using sykes pickavant terminator
@andrewgallagher87568 жыл бұрын
Thats great! I see its all mainly irish cars in up in the north and its great to see people using their knowledge to help others! And its cars we are aware off and not all U.S specs lol cheers
@bodgitandleggitgarage8 жыл бұрын
+Andrew Gallagher thanks mate
@johndoherty86816 жыл бұрын
been looking at this video all looks easy , but been looking at the wiring on my car and two plug sockets fitted witch i have been told that they where but there when the car was made and told that there for caravan trailer sockets would but a pic up but do not know how
@bodgitandleggitgarage6 жыл бұрын
john doherty hi mate don't really understand what you are saying but yes there is two different sockets one for a caravan which charges a leisure battery and one for the trailer lights or caravan lights
@johndoherty86816 жыл бұрын
hi sorry you did not under stand , what i should have said that the two sockets that are fitted in my peugeot where fitted the time the car was made ,so the one socket that is there for the lights can i run a tow bar on it cheers
@gavinhole92962 ай бұрын
Yeeeaaaa haaaaaa!
@stuartmurphy68005 жыл бұрын
Would love to know is it the same for a 2002 vauxhall zafira
@bodgitandleggitgarage5 жыл бұрын
Hi mate the wiring on the towbar will be the same colours but the wiring on the car will not be if you follow the same procedures you will be ok you just need to make sure if you need the canbus box for your car
@stuartmurphy68005 жыл бұрын
@@bodgitandleggitgarage it don't have led lights and no ecu at the rear for canbus lighting anything before 2005 I've read is safe.
@BillsAllotmentDiary7 жыл бұрын
Hi buddy i've asked question on this before but now getting round to putting the tow bar on. My Citroen C3 2002 model I believe is multiplex wiring? The towbar I have is new but bought as second hand the guy wrote some instructions down which make absolutely no sense ( so yep there are no wiring instructions ) the kit i'm using is like the one in the video but has a small box attached which I believe is the sounder to let you know when the indicators are off or on. will need advice on that as well but for now. I have a 3 lead digital tester can I use that to test the car plug connector as you do with your tester? I'm guessing yes? can send a picture if needed. Also the towbar is already wired to a 7 pin plug, I see these are normally wired one way IE the break lights to say pin 6 is this universal for UK / Ireland? Ive had a few people say that the C3 light wiring can be problematic and can damage the ECU if wired wrong so any advice would be greatly welcomed buddy? I got a quote for a garage to do just the wiring this was £60 so would like to save that if can do it myself Cheers Bill
@bodgitandleggitgarage7 жыл бұрын
Billy The Loam Gardener hi mate it's very hard for me to tell you what to do as to be honest I do not understand your message you will have to send me pictures I might build to get a better understanding then
@BillsAllotmentDiary7 жыл бұрын
bodgit and leggit garage cheers mate I've done more research and think i got my head round things. as the towbar was from another C3 same year and not needed a relay box I'm assuming it's not full cam but i think similar wiring to car you put the towbar on. my main worry was the ECU being damaged but as there is no voltage except the signal going back to the ECU i cant see it causing an issue to the ECU am i right in that thinking? if so then i can take a pic of the tester i have to see if it's ok using that for the checks you did could i also use a multi meter. i know its hard to explain and understand your confusion just hoped I'd explained better cheers bill
@bodgitandleggitgarage7 жыл бұрын
Billy The Loam Gardener hi mate give me the details of your car number plate Exeter I will find out if it needs the box
@BillsAllotmentDiary7 жыл бұрын
Hi mate Iv'e messaged you the details you asked for cheers
@BillsAllotmentDiary7 жыл бұрын
Hi mate did you manage to find the information for me sent you a pm with the details. Cheers buddy
@lukazleong4 жыл бұрын
How big fuse u suggest ? Ha
@mikestorey62422 жыл бұрын
Mk3 cortina
@grahamharradine96384 жыл бұрын
i have a 2010 audi a3 what side should i wire it from NS or OS i dont have led do i need a box ?.
@BillSikes.4 жыл бұрын
Yours is canbus, dont do it without a canbus relay, it dont matter what side you use, but industry standard is usually offside
@bodgitandleggitgarage4 жыл бұрын
Very good advice
@paul-ne1bh4 жыл бұрын
hello can you help me ,i have a peugeot 3008 year 2011 i have put a tow bar on it i am putting the relay on the wire loom of the car do i have to take the negative leed of the battery many thanks
@bodgitandleggitgarage4 жыл бұрын
Always best to use the power from the battery as it's completely separate from all the other systems you can use an earth at the back just make sure you have a separate Earth and it's not shared with anything else
@paul-ne1bh4 жыл бұрын
@@bodgitandleggitgarage many thanks my problem solved ,i have a 12 volt point in my boot can i take the live of that with a fuse fitted
@bodgitandleggitgarage4 жыл бұрын
@@paul-ne1bh I personally wouldn't do that mate you want a standalone 12-volt direct from the battery but it's your car you can do what you want
@paul-ne1bh4 жыл бұрын
@@bodgitandleggitgarage i will take a live of the battery like you have told me to, you have been a big help thanks a lot
@bodgitandleggitgarage4 жыл бұрын
@@paul-ne1bh anytime mate I'm glad I can help
@swedensy3 жыл бұрын
I have no wires on left or right. Only amplifier and fm unit. Audi A4 quattro 2006.
@thestiffmeisterguesswhosba92604 жыл бұрын
Where can I get a good tester like that
@bodgitandleggitgarage4 жыл бұрын
ebay mate
@TheM6aae8 жыл бұрын
sorry the DSO I meant...
@bodgitandleggitgarage8 жыл бұрын
hi get it from uk and ist a hantek dso 1200
@eotvosmarcel676 жыл бұрын
Hi.Sorry but how it is possible when I put my car on reverse the electric is going for ewerithing.Its not wireling for nothing.Its Peugeot boxer 2005.
@bodgitandleggitgarage6 жыл бұрын
Eotvos Marcel hi mate I'm not too sure what you mean but what I would suggest to do is look at your rear light make sure you have no water corrosion on the connections or any cross wires
@eotvosmarcel676 жыл бұрын
bodgit and leggit garage Hi.Thank you for answer.Yes I change caster.Was rusty.And was wrong eart.But is work now.Thank you.
@tonywatson1412 Жыл бұрын
If black is ,left tail. And brown is right tail. Then why not connect to the proper corresponding wires on the car
@bodgitandleggitgarage6 ай бұрын
🤣🤣🤣🤣🤣🤣 Where to begin with this message? Did you not watch the video? Did you not see everything working properly and correctly in the end? So obviously I connected it properly. If you are trying to say you have to join up with the same wire colour in the car then wow just wow
@martinwalters6285 жыл бұрын
I hate to disagree but you should not connect left and right tail lights together and increase the fuse rating. You should run twin cable across to the opposite side and connect both side lights separately as well as the indicators and leave the fuses as they are. Bad practice to uprate fuses.
@bodgitandleggitgarage5 жыл бұрын
If you understood properly you would understand that it's no problem do you know what in series/ in parallel means
@barryporteous49044 жыл бұрын
CAM? bus?
@TheDeclanking5 жыл бұрын
It's not can bus wiring it's pulse width modulation pwm
@napper14962 жыл бұрын
If it’s a newer car this is wrong as you’re going to end up costing folk money and warranty issues. Newer cars are canbus and if you do this it’s going to make car throw codes etc
@bodgitandleggitgarage2 жыл бұрын
Before making comments make sure you read the title properly and watch the video properly I clearly state this is how you wire a Towbar Without canbus I have done another video how to do it another video how to do it if your car has canbus wiring
@bodgitandleggitgarage2 жыл бұрын
Your comments has absolutely no relevance to this vidno relevant to this video I don't understand why people do this why people do this especially when You don't read the title or watch the video properly just try and make just try and make a smart comment to make yourself comment to make yourself feel good or look good when it has absolutely nothing when it has content of the video
@johnyqtx3 жыл бұрын
So I'm watching how to wire a 2001 golf with this video... And get an ad for the new Bentley Continental GT V8??? Cmon Google/CIA/BillGates/MI5/BigBrother, you can do a lot better than that...