Great video. I will be fitting a tow bar to my vw transporter 2007 t32 next month and this will certainly help me. 👍👍
@YoucandoitwithJules3 ай бұрын
Thanks for the feedback and let us know how you get on. You can do it 👍
@CheckEnginePlusMinus3 жыл бұрын
Very good job 👍👍💪
@YoucandoitwithJules3 жыл бұрын
Pleasure hope you got it wired up ok. You can do it.
@FrankgoddenАй бұрын
Hi I've a 2010 t5 can I wire it straight in the loom I thought Cambus was for led lights
@YoucandoitwithJulesАй бұрын
If it's can Bus which was Facelift T5.1 then no, check on Rosstech website for more details on can bus. www.ross-tech.com/vcds/canbus.php Let us know how it goes. You can do it 👍
@markrichardson70823 ай бұрын
Hello there I have just purchased a tow bar for my 2007 vw transporter 2007 t5 / t 32 and with the tow bar is a really would your advice be to fit the rely or just go straight into the loom. Many thanks
@YoucandoitwithJules3 ай бұрын
2007 straight into loom is much easy and doesn't effect the electronics. Keep us posted of what you do. You can do it 👍
@markrichardson70823 ай бұрын
Thank you for your reply. Will keep you posted. I maybe a little while until I get chance to fit the tow bar but I will message you 🤜🤛👍
@iDiveDOTtv Жыл бұрын
Hey that's a fantastic video. Clear and concise 🙂 Does this way not make it throw any errors with CANbus or anything like that? I had thought there needed to be some jiggery pokery done so that alarms didn't start flashing on the dash.
@YoucandoitwithJules Жыл бұрын
Hi for the vans 2009 and before (Ie T5) all good. Later you need a relay setup but shouldn’t throw any errors unless a light out. Hope this helps. You can do it 👍
@iDiveDOTtv Жыл бұрын
@@YoucandoitwithJules Cool. That sounds nice and easy then. I didn’t really know what the can bus stuff was but seems it’s just super low voltage or power. Knowing I can bypass it with relays and not throw a light is good. Thanks for the video 👍
@sambrookhouse47754 жыл бұрын
Great video. Did you have to fit anything/ spacer to pack out the towbar to enable the rear bumper to fit correctly?
@YoucandoitwithJules4 жыл бұрын
Sam Brookhouse Hi just seen this question. No I didn’t have to pack anything it fits perfectly. That’s with a Westfalia TOWBAR. If it’s not that make then I can’t comment. Hope it goes well and let me know 👍
@uwtab68983 жыл бұрын
I've tested the wires... Wire 1 and 3 both respond to the direction light to the left. Completely confuses me.. Any ideas anyone? I wish I could just find an diagram of the car wires there,.. but haven't found any after many many hours of searching.
@BeauMadeline3 жыл бұрын
Hi. Where did you take the positive power supply from? Cheers.
@YoucandoitwithJules3 жыл бұрын
Hi I’ve just spliced into the cables in the wiring loom. If you are talking about a main positive for a caravan I haven’t wired that up in this video.
@BeauMadeline3 жыл бұрын
@@YoucandoitwithJules no worries. Cheers mate. I've ran 2 cables to tge engine bay. Managed to find a good easy access not far behind tge battery. Thanks for the reply. Think I'm sorted.
@YoucandoitwithJules3 жыл бұрын
Nick Oliver Hi, yes there’s a hole in the bulk head behind the battery, if you take blackpanel out behind the battery. I cover it in my video about mains feed into the van. You can do it
@YoucandoitwithJules3 жыл бұрын
Also on some vans there’s a positive mains feed under the left hand seat ( also covered in the video) You can do it 👍