I notice there's zero sealant on the head of the bolt and the washer That's a great place for water to seep in. Rip transom in 3 years.

They used to call that bracket the Grady Drive. Not sure who made it but that was definitely made for Grady stock. Bad for peeling. Had one for years.

Great work. I can’t understand why owner didn’t sandblast and repaint bracket if he didn’t have money to replace it. 😩

I had the same boat. Pre 90 hull. Grady really went cheap back then, plastic thru-hulls, suppers below water line. Didn't glass any holes after drilling.

You guys are absolutely amazing, thank you for sharing !!!.

when used hummer never turn bolt, only nut! if turn bolt by hummer hole became bigger and silicon moved out from hole, will leak soon !

All that work just to put those awful Hondas back on 😢

The engine are inverted: propeller right rotation clockwise propeller left rotation anticlockwise. For the rest all perfect.

Aww yeah.. A-aron letting all the tools fall off so he can blame everyone later 😂. Who took my wrench??!

That makes sense get the transom repaired and nicely refinished then bolt the crappy corroded bracket back on?

Those Hondas look so heavy! Nice job, I just wish the fiberglass guy had done his magic to the bracket to match the transom. You guys still based out of the marina you were at last year or did you guys strike out on your own? If you did make a go at it on your own you would make a ton more money with just a little added headache. Technicians are becoming harder and harder to find.

Just curious was this an inboard motor boat before you went install brakes for a outboard motor

Nice work guys

why not make a plywood templet of the bracket with the 2 holes for your 2 mounting bolts then hang it to finish the drilling would that of been a little easier then all that shimming .. no? not telling how to do your job but thats how i did it on my old boat worked out perfect but love your work and videos

How to get bracket to sit the way you want it on forklift.... building shims. You can get them at a home building store like Lowes. Its easier than trying to find someone the exact right height... on this type of application you can use them over and over.

Regardless if it is covered by the bracket, should have removed the centerline marks created. Nice install, shame the owner didn’t spend the cash to replace or apply new powder coat to the existing bracket

How long did it take you guys to get that bracket level?

why you mount it so low? it should be much higher

@ 0:10 Donny, cracked me up

That’s my neighbors boat great vid guys

How to set engine mounting hole? hull bottom of ?

Good work my friend. Thanks for the videos

Did you guys relocate ? I just ordered a shirt i have some re power questions . If i had a choice of a Suzuki 250 or honda 250 which one would you go with ?

Tuesday means born again boating 😎

Nice job gents!

Looks like he eats a lot of square grouper and fudge brownies

love your videos. How about a scupper video?

I'd just built one out of aluminum more style

what is the purpose of a outboard bracket? what is in the core of it?

Why wouldn't the inside of the transom be finished to the top edge, wouldn't the idea to keep all water out to reduce the possibility of any damage? How many transom's need to be changed?

I have seen a bunch of videos like this do you contact the boat manufacture before you do this. I ran a quick calculation, and that bracket will add an additional torque to the transom of 1100 LBS just in a static load based on 500 LBS @ 24"that does not include the torque they produce or shock and vibration. I called Grady White and asked about putting a engine bracket on that boat They said no you should not do that it was never designed for that and will not handle the added force and will screw handling center of gravity among a long list of other things.

Why on earth would you not address the bracket condition?

Where did you get/buy the bracket from?

Would have been nice if you were telling us how to measure for a bracket

your helper is gorgeous

Why does the motors have to be so far from the back of the boat?

Great work! 👍👍👍

Why didn't you show marking and drilling the center holes?

Needs to be a Manbun alert in thumbnail

Not clear how you find the centerline. Could you please better explain it?

What did they redo the transom core with if you remember?

Why didn’t you just make a template and pilot drill the mounting holes instead of all the messing around with the forklift and shims

The engines weren't counterrotating?

Anyone have tips on finding a 30ft center console ? Hull only

Hi can u please provide me the measurements for building a transom for my regal 2665 to convert from inboard to outboard

good luck on your boats i quit everyone keeps selling me to sell it and I think I am everyone is pushing my dream away :(

Like everone else said it's a grady bracket. I have one on 25 dolphin. I have twin yamaha f225s and they touch when almost fully turned. I plan to replace it, but prices are way to high right now

When did you get a female coworker?

Great work👌🏻

It wasnt even several years ago I sub'd this channel, back in the beginning, it was about High End Ultra cool navigation installs and slick High Performance lake and sea craft. NOW it's all about fixing junk and draining milky lower unit lube. time to Move On...

I have a transducer question. I had a Sim rad crew seven and transducer installed a couple years ago and the transducer has always been loose where it mounts to the bracket is this correct? Should the transducer move to allow for play or should the bracket bolt be tight?

I found some ready made once on usa websites but the price including transport and customs in india is costing a lot if u can assist me in building one it would be great

Tripod and small hoists work the best. All the rot in those boats came from rigging. They didn't glass the drill holes or cuts (notch transoms) the big disappointment was the scuppers under water line at the dock. If a hose popped off it would sink the boat. Lesson learned, research the year your boat was built (recession years) and the CEO of the builder. Alot of those guys sacked quality companies for the sake of huge exit bonuses. Look at OMC, one guy ruined that company.

Where are you guys located in Florida?

Where are these guys located

The shot I needed to see was the inside. The lower corner bolts that seemed to barely make it into the bottom hull. The inside shot would have shown the bolts relative to the stringers is what I would like to see. Your not really filming for other mechanics

nice job

curious as to how long and the cost for a job like this?

The boats a little crooked on the stand

Hi I am from India can u please assist me in converting my regal 2265 to outboard because getting a ready to fit welding world is costing a fortune due to transport custom duty etc

and now after all that cant afford the fuel lol

I was going to say what others have said, cleaning up the bracket prior to installation should be pushed. The idea of installation, hanging engines on, rigging and already had a new transom installation is just stupid. Are they going to install a couple blown engines, since that seems to be the mindset? How much to bead blast ,prime and paint? Sounds like the owners have spent to much time in the sun.

Where can I get a 36 Center cancel boat for cheap

looks like Inboard original. Engine WAS likely almost originally placed in the forward/middle. I'd be skeptical about The Balance having been hyper-extended she gonna porpoise as she tries to Plane Out. That would be a very heavy hull, with all that twin engine torque lifting that beast? I must have missed How all the hardware and controls get to the engines? I'd never advise this variation from design.

You sealed the bolt holes with 5200 between the bracket and transom. I was wondering if water can get through the actual hole where the nut and washer is?Do you have to seal it as well?

That old bracket needs some 20-year-old Evinrude's

멋지네요 very nice video

Owner put that big ugly bracket on that nice clean transom

this transom wil rottig soon, the whaser wil let water tru the bolt into the transom , i did not see you put anny seal around the bolt it self only on the transom and braket. yeh yeh i know my spelling sucks dont shoot me i a domb dutch farmer

To bad owner didn't refinish bracket base at least.

Comment for the algorithm

Can u please assist

Not prepping and painting that bracket before installation makes poor sense, wtf

You are torquing bolts from the wrong side - basics of the mechanics.

I thought you were better that. Layout was great until you ignored all your marks and downhill from there. Bolting a rusty old banged-up bracket to a Grady White with a newly restored transom? Ridiculous.

Usually, I do the same alone twice faster))

I thought that was a chubby woman till it spoke.

bad service

Cherry picker

Lot of keyboard captains in the comments this time @bornagainboating

Add a bracket an Armstrong bracket put on my 245 seahawk sport cabin model. Declosing the Stern the cost of the bracket? And mounting? The. Bracket? Cost. Me $5000 it was well worthat I had twin 115 Mercury's on It

Comment for the algorithm