Don't break your drone like I did! My unboxing, review, setup, and repair of the Happymodel Mobula6 2024!
Пікірлер: 27
@godangle24 күн бұрын
You gotta be careful with lactate, it is plastics. When you say "Loctite all screws", someone might accidentally Loctite the canopy screws. The best practice is to check for loose screws periodically especially after big crashes.
@jbaked258522 күн бұрын
I use a post level to set my drone on for calibration. Generally they’re taller than 6 inches which allows for the cord to point down. I also get a physical indication, in the level, that the craft is actually on a flat surface.
@Braincho26 күн бұрын
Nice vid bro. 4:45 - you can fit BT2.0 plug into A30 - it goes in smooth so no need to solder/resolder.
@CG-RC26 күн бұрын
Thanks for the info!
@XxKiloxX40626 күн бұрын
Im new to ELRS and this is exactly what I needed to see to get mine setup! thank you!
@CG-RC26 күн бұрын
Glad it was helpful!
@shogunemperor26 күн бұрын
Daaaamn bro! Awesome video!! Love how detailed you are!!!
@iRazvan274526 күн бұрын
i was so focused on your video that i was filling my cup on the side it spilled everywhere 😂
@CG-RC26 күн бұрын
😅
@darwin_win21 күн бұрын
Hi, God damn, I love your post! It was awosome. New Mobula6 looked damn good! By the way, your recorded video was pretty good without much noise or break up with analogue. Can you tell me what goggles and reciever are you using? I am using skyzone o4o pro and stock reciver for my mini whoops but there is much noise and break-up. Thank you bro!
@CG-RC16 күн бұрын
I am using the HD Zero headset with the TBS Fusion analog video receiver module. Its a good combo!
@nyclassic4ever13015 күн бұрын
Thats the Eco
@Hellfire_FPV27 күн бұрын
very cool
@BergeronFPV27 күн бұрын
Never locktight a motor screw, Just buy spare screws. I lose mine alot, you can buy like 1000 pieces of them for about $5, When you land nice and flat you can hear the metal screws click, there taking alot of the impact. M1.4 x 4mm works, you can spend more money for titanium to save on weight. Make sure they aren't countersunk tho. Countersunk screws would start the 4mm measurement from the top of the head. I made that mistake recently.
@smika71027 күн бұрын
RIP 3/4 motors of my first build. Screws ripped off locktite to the motor
@CG-RC27 күн бұрын
Good info. I haven't had an issue with lock tight on my drones before. But better safe than sorry. Thanks for the advice.
@smika71027 күн бұрын
@@CG-RC if you have dexterous hands & allocate the correct amount it bet it works.
@godangle24 күн бұрын
I know it seems counterintuitive, but if you turn down your VTX power indoors, you can actually improve your signal because reflected signals can cause interference, especially a higher power levels.
@BergeronFPV27 күн бұрын
you dont need to change that plug it holds bt2.0 in tight. you want it.
@CG-RC27 күн бұрын
Cool, I didn't know that. I guess I should have tried it first. lol. Thanks for the feed back!
@brandon968927 күн бұрын
My analog 2024 mob 6 lost video feed in 2 packs. By far the worst experience I've had in FPV so far.
@o-rex389817 күн бұрын
Find a way to fix it?
@smika71027 күн бұрын
May as well not add music
@CG-RC27 күн бұрын
I am curious, why do you say that? Also, which section? Just trying to figure out how to make better videos. Thank!
@smika71027 күн бұрын
@@CG-RC 16:20 is rough. Sounds like white noise over a drum beat with a drunk person screaming xD