Bsa B31 Plunger Restoration Part 11
Рет қаралды 8,467
3 жыл бұрынMore work to the engine, chaincase and other stuff.
@UPTHETOWN 3 жыл бұрын
Looks better than new
@500dbd34 3 жыл бұрын
Cheers
@wank7763 2 жыл бұрын
I love this video restoratiin BSA .
@singhkarm6520 8 ай бұрын
Very good work
@500dbd34 8 ай бұрын
Thank you! Cheers!
@bradfisher478 2 жыл бұрын
Magical
@500dbd34 2 жыл бұрын
Thanks for the comments, always appreciated. Cheers B
@T8Hants 3 жыл бұрын
I am playing catch up with this series as I have a 1949 B31 rigid, but I also have the option of going plunger as I have a spare frame.
@500dbd34 3 жыл бұрын
Good luck with you project.
@colinbagshaw1796 3 жыл бұрын
For future reference your chaincase slider seal is 180 out, the flat end goes to the rear FYI :-)
@500dbd34 3 жыл бұрын
Correct, well spotted.
@EveAntony 3 жыл бұрын
How long did it take to complete this 35 min. work in real-time?
@500dbd34 3 жыл бұрын
Hi, not sure if I have replied to you but the original video files were about 1 -1/2hrs long, I use 4 and 2 times speed and lots of editing, otherwise it would take ages to watch. Thanks B
@davidclapham1066 3 жыл бұрын
Hi Brian, is the chamfer you put on the top piston ring just for ease of assembly, or for some other reason?
@500dbd34 3 жыл бұрын
It was not rebored but new rings fitted, a light chamfer on the top ring clears any lip that may be at the top of the bore. only a very light chamfer or some compression may be lost. Cheers B
@sutrisnobayu6613 2 жыл бұрын
Like
@brianthombs8668 2 жыл бұрын
hi Brian, when you fit the sliding plate onto its felt gasket, have you bolted it down tight to the case or left it slightly loose so free to slide, I noticed you used loctite on the bolts.
@500dbd34 2 жыл бұрын
The slider needs to move a bit so i dont overtighten the bolts, I just back them off a bit. Mediun strength Locktight holds them secure but can be undone easily when required. I fitted the slider the wrong way (see comment below) try not to do that. Anyway thanks for the comment though, appeciated. Cheers B
@brianthombs8668 2 жыл бұрын
Many thanks Brian, very helpful. Great series. Regards Brian T
@MartynStubbsTBS 3 жыл бұрын
Mr Alfonso will you change the original point's for electronic? If not why not?
@500dbd34 3 жыл бұрын
This is a 6volt Magneto model and i'm not sure if electronic would work. I want to keep it as original as I can, Thanks for the comment.
@paisaboltahai4751 3 жыл бұрын
Upload the Next part of 12 please as soon as possible
@500dbd34 3 жыл бұрын
kabir khan , won’t be long
@alexisfelix8308 3 жыл бұрын
Its verynice, I have not seen the head gasket,?
@500dbd34 3 жыл бұрын
Hi, no head gaskets on these engines but it’s good practice to Lap the head and barrel. Cheers
@alexisfelix8308 3 жыл бұрын
@@500dbd34 thanks for the message,I love this
@paisaboltahai4751 3 жыл бұрын
Please new video Uploaded part 12
@500dbd34 3 жыл бұрын
Be ready on Sunday, thanks
BalcevMMA_BOXING
Рет қаралды 14 МЛН
Brian Alfonso
Рет қаралды 6 М.
SolidWorks Tutorial ☺
Рет қаралды 6 МЛН