Sparex Ferguson TEA20 # 5 Removing the piston.

Рет қаралды 11,574

4 жыл бұрын

This is a video on pulling the pistons, the sound is a bit quiet on this one.
Here is a link to the Kangaroo Stew where I bought it and got it running.
• Kangaroo Stew # 165 I ...
Some of the links I talk of in the introduction are below.
Queensland Tractor Spares Web Site:
www.queenslandtractorspares.c...
Queensland Tractor Spares Ferguson Parts Category Short Cut:
www.queenslandtractorspares.c...
Queensland Tractor Spares Technical Tab:
www.queenslandtractorspares.c...
Queensland Tractor Spares Downloadable Sparex Catalog Tab:
www.queenslandtractorspares.c...
Sparex Australia Web Site:
au.sparex.com/

Пікірлер: 39

@chrisduggins3435 4 жыл бұрын

Super good video series for a TEA Ferguson

@BundyBearsShed 4 жыл бұрын

Glad you think so!

@rustybum2 4 жыл бұрын

Thanks for this brilliant series Lance--------mind you, I wish I'd had this to refer to 20 odd years ago when I'd bought a TVO 20 in bits. Thankfully it was all there and I only had to buy new rings, shells, gaskets etc and I must have done it right because it;s still running fine today. Thanks for sharing, from a geriatric old fart in Ireland.

@BundyBearsShed 4 жыл бұрын

Thanks for dropping by, glad you enjoy the series.

@Spodokamono 4 жыл бұрын

These are excellent helpful videos Lance. While watching this I had 2 more video notifications from you as well. Wahoooooo. You'll have this finished by Sunday at this rate 😀 Jude will think she is getting taller the next time she uses the brush. 👍👍👍👍

@BundyBearsShed 4 жыл бұрын

Glad you like them! It keeps me busy.

@charleshart6992 4 жыл бұрын

Excellent video Lance - you make it look so easy! especially upside down!

@BundyBearsShed 4 жыл бұрын

Thanks 👍

@ianahmet9286 4 жыл бұрын

Great video Lance on the Tea 20 you do a good job , cheers

@BundyBearsShed 4 жыл бұрын

Thanks 👍

@transliv03 4 жыл бұрын

Excellent series, Lance. Good on you for sharing a lifetime of experience and tips, making it so much easier for the rest of us. All the best. Tony.

@BundyBearsShed 4 жыл бұрын

My pleasure!

@tijnvanbeekuitsneek319 4 жыл бұрын

Thanks Lance from the Netherlands, very good video. Stay healthy!

@BundyBearsShed 4 жыл бұрын

Thankyou, you as well.

@davidthomas1732 3 жыл бұрын

Your a Bloody Gem Lance. Thanks for sharing your knowledge.

@BundyBearsShed 3 жыл бұрын

Glad to help

@billweir6770 3 жыл бұрын

Another great series Lance...I'm back in another 14 days quarantine, so these are a brilliant way to fill my days. We did a TEF 20 a few years back and it did not have the offset bottom ends.....what a ball ache that was to fit the pistons/rings and liners back together - it really tested me and my brother, but we got there in the end. That would make a great video is you ever get one in your shed

@BundyBearsShed 3 жыл бұрын

I have one tucked away and even have the engine kit to fit if I can find time.

@billweir6770 3 жыл бұрын

@@BundyBearsShed Brilliant, I'd love to see that one day

@pm270100 4 жыл бұрын

good vid well done ///thats a low comp motor needs 671 blower on it

@BundyBearsShed 4 жыл бұрын

Wouldnt hurt.

@johnkinnane547 4 жыл бұрын

G'day mate good TV Regards John

@BundyBearsShed 4 жыл бұрын

Thanks John.

@smokeytexx 7 ай бұрын

why new liners before measuring may of got away with a hone and new rings ????

@BundyBearsShed 7 ай бұрын

Possibly but Sparex supplied a kit for me to fit. It was dusted badly though.

@popkinson 3 жыл бұрын

Hi Lance. Is the oil pump key driven from the distributor replaceable from the distributor side, rather then having to remove the sump again. ?

@BundyBearsShed 3 жыл бұрын

Yes the gear and shaft comes upwards after removing the distributor.

@chrisjackson4457 4 жыл бұрын

That looked fiddly lance trying to do that and film good stuff though 👍

@BundyBearsShed 4 жыл бұрын

The filming makes it interesting at times but not to worry, I fiddle along through it.

@scania1982 4 жыл бұрын

Mr. Bear, do you know if the main bearing caps are supposed to have locating dowels just like the con rod bearing caps? On my tea-20 the main bearing cap lacked dowels.

@BundyBearsShed 4 жыл бұрын

I dont think so, I have a video on the crank coming up but I didnt remember seeing them.

@hirenyadav6288 4 жыл бұрын

creakshaft oversized 10

@BundyBearsShed 4 жыл бұрын

No looks to be standard on this one.

@motorv8N 4 жыл бұрын

Great video Lance - more terrific tips. Question - my '52 has a bit of a clunk under load (on that poor No. 4 as far as I can tell). Assuming no major crank journal damage, is it possible to tap the old bearing shells out from underneath without pulling the head and pistons then slide new ones in the same way? Thought I might try the cheapest solution first....😬. If the crank is indeed flat enough to warrant machining or replacement I figure the unhappy sounds will be back in short order....

@hooter7003 4 жыл бұрын

motorv8N sure can fairly easy

@BundyBearsShed 4 жыл бұрын

Yes no problem doing that, just don't let the piston come down too far in case the bottom ring pops out the bottom. Im not sure if it can happen on these engines but just be aware of it as it can stuff up your whole day.

@BundyBearsShed 4 жыл бұрын

I might look at a centre main to show what can be done.