Sheet Metal Tutorial | Engine cover design in Creo Parametric
Рет қаралды 19,339
4 жыл бұрынLets design sheet metal part in Creo Parametric
The basic sheet metal design
• Sheet metal Design in ...
Unbend Sheet metal
• Sheet metal Unbend in ...
Mapkes in Creo Parametric
• Create mapkeys, Nested...
@SuperJJ37 3 жыл бұрын
Great job!
@user-jk9fb8py9k 4 жыл бұрын
good job! love your videoes!
@kbnchannel1991 4 жыл бұрын
Useful one
@ganeshn.6847 Жыл бұрын
great one sir...
@anitahase7621 3 жыл бұрын
Hello sir please share link for punch and notch command in surfacing
@kirankhairnar8678 4 жыл бұрын
I get a lot of inspiration from your videos Create a video like this
@omegaalpha5735 2 жыл бұрын
Mera bend back command fail ho rha hai… kya karu
@EETLASIUENGINEERINGSERVICE18 Жыл бұрын
Aapki wjh s m design engineer ban pai. Pahle degree thi sirf.
@prakashsutar2846 3 жыл бұрын
though i had followed each step exactly shown in video whenever i am trying to unbent it shows me error as "Highlighted swept flange walls cannot be unbent. Recommended actions: Redefine flange wall section or trajectory." can you please guide.
@CADxTraining 3 жыл бұрын
Try to reduce the flange height and check
@amritkaur2949 2 жыл бұрын
same issue
@CADxTraining 2 жыл бұрын
Try to modify the dimension of the flange
@mohammedmusthafa90 4 жыл бұрын
Hi sir, great explanation. can you share the those drawing pdf for practicing ?
@CADxTraining 4 жыл бұрын
You can take a snapshot in hd resolution from the video.
@BerkMirnak 4 жыл бұрын
I'm using Creo 5.0 and Creo can't unbend the design. Is there a problem with me? or maybe the version? By the way it's really inspirational video. Thanks for that.
@BerkMirnak 4 жыл бұрын
Sorry, problem is on me. The measures are inch not mm, i figure it later.
@mechlown 2 жыл бұрын
Hello, I am following this tutorial but the "Unbend" function fails in the regeneration... Any hints for that??
@CADxTraining 2 жыл бұрын
Try to increase the part accuracy.
@mechlown 2 жыл бұрын
@@CADxTraining the only difference I see is that, when I make the flange, i have to select one by one all the edges, while I saw that you do all in one time. Can be this the cause of failed regeneration? just in case, can u explain how do you select all edges in one time? thanks
@DigiSculptStudio 2 ай бұрын
@@mechlown right click the edge and then left click
@normanny7760 2 жыл бұрын
there is unbending problem what to do?
@CADxTraining 2 жыл бұрын
Try to increase the accuracy. Go to "File-prepare-model properties-accuracy" and increase the accuracy. Change the value to 0.0001 that's it.
@normanny7760 2 жыл бұрын
@@CADxTraining THANKS IT WORKED
@chetanadsul2394 4 жыл бұрын
Why did you took 30 degree taper angle while it is given as 120 degree
@CADxTraining 4 жыл бұрын
It's 30 degree one side and 120 degree other side. You can go with any angle depending upon your side.
@chetanadsul2394 4 жыл бұрын
@@CADxTraining ok
@normanny7760 2 жыл бұрын
AFTER DIVIDING I CANNOT MAKE THAT AS START POINT WHEN I CLICK ON RIGHT CLICK THE COMMAND WINDOW IS NOT APPEARING
@adityakshirsagar6059 10 ай бұрын
need to long press of right click
@normanny7760 10 ай бұрын
@@adityakshirsagar6059good luck for your future
@kirankhairnar8678 4 жыл бұрын
Make a video copy Geometry and Public Geometry plz
@vineethteja322 2 жыл бұрын
unbent is not happening, it is showing error. after modifying the flange dimensions also i am getting the same error.
@CADxTraining 2 жыл бұрын
Increase the part accuracy
@vineethteja322 2 жыл бұрын
@@CADxTraining I made it 4 times Bro, but still I'll work on it.
@CADxTraining 2 жыл бұрын
Change the part accuracy
@satishsingh-sy6nn 2 жыл бұрын
Dear sir in Creo 3.0 this section in not unbend plz give the solution
@CADxTraining 2 жыл бұрын
Move the flange outside the edge.
@satishsingh-sy6nn 2 жыл бұрын
@@CADxTraining still not unbend in this also it shows error Highlighted swept flange walls cannot be unbent. Recommended actions: Redefine flange wall section or trajectory.
@CADxTraining 2 жыл бұрын
Try to increase the accuracy. Go to "File-prepare-model properties-accuracy" and increase the accuracy. Change the value to 0.0001 that's it.
@satishsingh-sy6nn 2 жыл бұрын
@@CADxTraining itS done thanks
@CADxTraining 2 жыл бұрын
Good to hear.
@sandipsamanta7075 11 күн бұрын
Unbend is not working at 8.33
@CADxTraining 11 күн бұрын
Increase the file accuracy. It will work. kzfaq.info/get/bejne/np6TedOSm53Sdn0.html
@sandipsamanta7075 11 күн бұрын
@@CADxTraining Thank you so much. Its worked. I tried multiple times but I failed. Thanks for this support & your video is very informative.
@ganeshkurade4968 Жыл бұрын
Sir drawing is not visible
@CADxTraining Жыл бұрын
Play the video at 1080p
@siemenscadsolutions9994 Жыл бұрын
Excellent video #siemenscadsolutions
@besko269 4 ай бұрын
Why i cant use bend back?
@CADxTraining 4 ай бұрын
If you are getting any error then try to increase the file accuracy.
@besko269 4 ай бұрын
"Feature failed to regenerate" always show me this
@besko269 4 ай бұрын
Highlighted surface cannot be bent back. Highlighted swept flange walls cannot be bent back. This two messages also
@CADxTraining 4 ай бұрын
Increase the file accuracy and try
@besko269 4 ай бұрын
I tried that too, but everything is the same again
CADx
Рет қаралды 17 М.
StarTech TV
Рет қаралды 9 МЛН