Finally the actual camber adjustments shown in the video, and this video is 11 YEARS OLD! Great video and I hope you see that this comment shows this video still helps people! Thank you!
@Stover19282 ай бұрын
I have looked for a video like this for several years! The ONLY video I have found that shows and explains the procedure in plan language . Thank you!
@ethanporter21078 жыл бұрын
wish other companies were this informative with p their products
@RgW00D7 жыл бұрын
Boomba and Mishimoto do amazing informative and install videos.
@AllAppleAllDay12 жыл бұрын
Great video! Really helps understand how the camber bolts work!
@romantrucha12 жыл бұрын
@kaleAe92 only if you'r looking for minimum change in camber. for more extreme hella flush style you need new struts baggs coilovers etc. depending on your budget and taste
@miltown76 жыл бұрын
thank you for you time , got your self a follower !!!!
@ercilvet7 жыл бұрын
Thanks for showing how to install your camber adjusters, it really helps ensure less screw-ups. Now,...... go bitch slap the guy who thought making a video in 240p was a good idea!!!
@ihavefallenandicantreachmy21136 жыл бұрын
Anything over 240 will melt your face and your camber bolts. You have been warned.
@waqarqadeer52178 ай бұрын
Thank you for explaining it so well ❤
@sam1118808 жыл бұрын
humm curious how this special cam bolt on the top struts is moving the wheel cylinder/rotor components out or in from the original upper strut mounting bolt , and where is the toe out /in setting is for the rear is it part of one of those lateral link arms in the back ( i though the lateral link adjustment bolts would be for camber instead of toe in ) Not sure still a little confused about the rear wheel adjustment in different types of vehicles.
@romantrucha12 жыл бұрын
depending how much of a drop the springs gave you sum cars gain negative camber when lowered but again thats all to your taste. but for a few degrees more yeah these bolts will help my SPC ones ran me about 20 bucks with shipping and all
@leeoneill87886 жыл бұрын
No comment but I have a question. Had my 2008 impala aligned after purchasing new tires the car had camber bolts by previous owner. Here is my question, does the camber always need adjusting? The alignment tech said no because the camber wasn't showing in the red after the alignment was done..
@thomaspattison924310 жыл бұрын
Like because you did it on an 8th gen corolla, the exact same car I doing this on haha
@shawnprime11433 жыл бұрын
Would this be the same procedure for a 2005 honda pilot? Too much negative camber to one rear wheel.
@micmar96707 жыл бұрын
07 corolla..how many camber bolt do the front have? 4? 2 on each side or 2 ? 1 on each side? thx
@natemarauder812 жыл бұрын
1. how much negative camber is possible to get from these? 2. what would happen if i put one on the top bolt and one on the bottom bolt facing opposite directions would i get double the camber angle?
@sunlite97594 жыл бұрын
Nice provided the wheel is straight and not pot hole bent. Car must be level side to side or you are just measuring an out of level car. (Measure height of car before lifting; then return to same height before adjusting camber.)
@georgiojansen77588 жыл бұрын
skip the first part tightening the nuts go immediately to last part I think alignment must be wheel on ground. now he had to do it twice.torqueing is good when the threads are clean.he made them dirty first time. goedendag
@anterpants10 жыл бұрын
All you really need is a level and a square to do these readings.
@spydr20212 жыл бұрын
i'm just putting lowering springs on my car, coilovers are too much, can i just lower it, then use these bolts so get the hella flush loook? im not trying to put too much negative camber either
@edwinlacbay55154 жыл бұрын
How about for toyota corolla 95 model is it possible to repair its toe in on the rear wheel?
@Hellahighlife11 жыл бұрын
My car is a dodge neon o4. I have a little - camber in the rear wheel. Can I do the same thing for stock bolts? It's stock height too.
@judges6912 жыл бұрын
Great Video, Thankyou. A+
@andez1012 жыл бұрын
that's to adjust camber? do i need to get that special tool or bolt? or what/ someone explain please?
@atif851110 жыл бұрын
I have Buick Regal 1999 LS. Does needs camber bolt adjustment ???
@yoramsadot27808 жыл бұрын
haw to shim rear alignment toe gap of 1/2 inch an each side
@mowithoutyou11 жыл бұрын
very useful video thanks
@JZXKenny11 жыл бұрын
Is it the exact same for front?
@tristin55410 жыл бұрын
Looking to add some negative camber to my set up. Does anyone know how much you can actually get out of this?
@RSx948 жыл бұрын
Is this on a golf mk3?
@sitinurdwilika58367 жыл бұрын
thanks , now my car camber :D just buy bolt :)
@84monterider12 жыл бұрын
Would this work on a Cadillac deville 2001
@user-gr1el2zz1q11 ай бұрын
My old stratus only has one strut bolt so the cam bolt is useless. Is there another way
@Anthony_in_Bloomington_Indiana11 жыл бұрын
While this work on the front wheel of a front wheel drive car? How much do the camber bolts cost?
@mackenzielamb65134 жыл бұрын
Will have to take tie rods into consideration.
@Dompass19992 жыл бұрын
ahh 2011 the good times
@Twizzlemytash12 жыл бұрын
helped so much thanx :)
@That.swole_ayala5 жыл бұрын
Ray romano??
@driftwhore12 жыл бұрын
Good
@CrazieFrogz9 жыл бұрын
i just installed struts and now on the passenger side I think the spring is rubbing the tire, i haven't done a alignment yet on vehicle. the drive side seems higher then the passenger side... could an alignment really fix my problem? i had really bad struts before the new installation...
@kirkw95skate9 жыл бұрын
lovepeacenotwar1982 if your tires are scrubbing you need wheel spacers but an alignment will only help if the shop does camber adjustments.
@CrazieFrogz9 жыл бұрын
yeah i just found out ford put out something on these the windstars and the spacers....
@shantaanunaage19773 жыл бұрын
where and how the price camber gauge
@TupacCrooks8 жыл бұрын
background music?
@seaperu15 жыл бұрын
new age
@mrlambo29722 жыл бұрын
I'm trying to look for Camber bolt torque specs and Im not able to find. If anyone knows can u please let me know thanks Nissan murano sl 3.5L 2003 fwd and need for rear dead axle.
@bulletclub4life11 жыл бұрын
Umm...Buy the tools? Google and ebay is a beautiful thing. Wish they both existed.. lol
@riverfallscory8 жыл бұрын
Where did you come up with the recommended labor time?
@mackenzielamb65134 жыл бұрын
In 3 minutes I can have the camber bare for adjustment. If knowing what to do this job, like any other one I've done, takes no time to do. Hardest part is rusty bolts.
@nlouisf10 жыл бұрын
does it work on all model
@MrMonoMate11 жыл бұрын
Hella flush.
@SexyJutsu9 жыл бұрын
is this something i can do on my own at home?
@oscarsevilla96589 жыл бұрын
No do it at a public parking lot instead.
@Rastameister8 жыл бұрын
Absolutely not because you need the alignment measuring equipment, camber angle specs, and expertise. You need to get an alignment shop to this job.
@oscarsevilla96588 жыл бұрын
+Rastameister chill b
@tee.tapia3808 жыл бұрын
+oscarsevilla09 jajaa nice respone
@hcashmore118 жыл бұрын
+What Ricers Do What Ricers do Yes if you buy a camber adjustment gauge you can
@riceburner47472 жыл бұрын
When u DISassembled bolt, u pulled left frm right. When u INstalled new camber bolt, u pushed right to left. Another words u reversed install. AM I WRONG?
@kaleAe9212 жыл бұрын
so you only need to change the top bolt?
@kusumdevi14972 жыл бұрын
Omni ka camber kaise hota hai
@katiebarrera85679 жыл бұрын
CAN DOES camber bolt good for a Honda accord 96 or not
@domiiniicanooactivo55919 жыл бұрын
Front part or back?
@user-jp8oh2el4j6 ай бұрын
Bukan itu sil harian belakang
@rosesantiago27967 жыл бұрын
Lol
@danteljackson7 жыл бұрын
most of the mechanics i run into seems to not even know what camber is... i ask them to adjust my camber and they just say "huh?" 😂 i see im gonna have to do it myself, dumbasses smh... how does a mechanic own a freaking alignment machine and dont even kno what to look for doing a wheel alignment smh
@KetogenicGuitars5 жыл бұрын
Hello there.This happens also here In Europe,Finland,Juva.So it is not inbreeding to claim? Local major car shop claims there is 300€ job to be done. They would not touch the chamber bolts because there is "something wrong". Bolts are too tight supervisor says. Is not that the reason in the first place why I take the car to their shop? They are supposed to dare touch those bolts?! I almost dropped right there on that lousy shops lousy counter...somehow manged out though... Obviously there was nothing to loose so we just opened those bolts and gravity did rest of the job. Chamber was immediately dropped to perfect. There must be some nice bump on leveled ground where you can check the result with plain eye.And of course the car is totally easier to drive.
@boostjunkie23205 жыл бұрын
Its not that they dont know how....They probably just assume like most people who want to adjust the camber that you are a dumb ass
@mackenzielamb65134 жыл бұрын
@@boostjunkie2320 no, the mechanic is still the idiot. For if a mechanic is to make money by fixing cars, playing stupid when someone offers you work is bad business. The dumbass mechanic could of had a paycheck, as the purpose of a job in the first place. Hardly see the customer a fool but the latter.