Camo Drive ... 30 feet of decking in under 2 minutes

Рет қаралды 48,281

4 жыл бұрын

That's right, 30 feet of decking installed in one minute 25 seconds using the CAMO faster tool. Yeah .... if you are a contractor ... you need this it will save you time & money ... not to mention your back and knees!
#camofasteners #deckbuilding #contractorsecrets #lifeatLDD

Пікірлер: 34

@obedargueta7284 Жыл бұрын

“Look how quick this goes” after he placed a roofing nail on each beam as a spacer and has to remove each one before putting down the next board

@kevinblanchard611 Жыл бұрын

Right! The nail is holding the board it's not spacing anything. This guy should work for Bidens crew of lying scumbags.

@DarrellWefel-ts2kr Жыл бұрын

You don't need the space treated lumber it'll shrink as it ages

@daodwali3654 2 жыл бұрын

alright tiger king

@smokeskull 2 жыл бұрын

That cool

@Slyder695 Жыл бұрын

Will it work for solid edge azek?

@TheRayDog 2 жыл бұрын

What I'm finding is the PT deck boards need to be bent into position at nearly every joist. There is no way to have a board placed over a long stretch with consistent spacing otherwise.

@greghartmann4984 2 жыл бұрын

CAMO has a new tool called Lever. Get a few of these and they will lock your deck boards straight and in place the entire length.

@cybrisma6564 2 жыл бұрын

how's that work, were your board already bolted at the other side? what If I prefer to have a tight space in between boards, will it still work? Luther

@greghartmann4984 2 жыл бұрын

The Drive tool installs the boards tight. In this installation Joe was using nails as spacers. You can gap the boards to any spacing you would with any other fastening system.

@michlalonde691 3 жыл бұрын

what about the screws you put first to hold the plank? now you have to remove them ...

@daltonbray4498 2 жыл бұрын

I believe you put a spacer between the plank that’s secured already , then from the other side use it to push the new plank into the spacer, camo drive does the rest!

@muffinsmuffins8074 Жыл бұрын

The nails at each joist are the spacers between boards and they act as the backing to hold the board in place while he is edge screwing it in

@timkevwitch862 Жыл бұрын

Why don't you put the screw in the other way so it pushes the board into the other board?

@kevinblanchard611 Жыл бұрын

Great question. I was wondering also.

@blitzinstripes3788 Жыл бұрын

He already did that side FIRST.

@aldoogie824 3 жыл бұрын

How's it perform with IPE?

@andrewslezak441 2 жыл бұрын

I believe Simpson Strongtie sells a stainless screw that is self drilling into Ipe. It’s a plug system as I think.

@GP-mw9nj 11 ай бұрын

we do it much faster with the grad system for decks from grad concept usa

@normanlace3655 Жыл бұрын

now you gotta screw the other side.

@timcopeland 4 жыл бұрын

never been a fan of those little holes it leaves. they are not invisible.

@lddinteriorsanddesigns 4 жыл бұрын

I've gotta say ... it is pretty hard to see the holes.

@greghartmann4984 4 жыл бұрын

I haven't seen anything less visible. Uhh... Hmmm.....I guess if it was less visible I wouldn't have seen it?? Anyway it sure looks nicer than screws through the surface and for about the same cost.

@timcopeland 4 жыл бұрын

@@greghartmann4984 we like Hidfast.

@andrewslezak441 2 жыл бұрын

@@greghartmann4984 it becomes real visible once the board dries out and the edges start to crack. Or the screw heads snap leaving the deck feeling loose.

@mastershredder2002 Жыл бұрын

Don't trust anyone who uses a Ryobi.

@KazakovNik 2 жыл бұрын

И за токую шляпу просят 20 штук ? ) да пятерик красная цена

@kenb6102 Жыл бұрын

Take that all you Ryobi haters! You don't need an expensive Dewalt or Milwaukee to do the job!

@rileycoble5842 Жыл бұрын

I don’t hire anyone that uses Ryobi. If you have one or two for uncommon tools that you use than I can see that. But if it’s for your main tool then I’m going to wonder what other things you cheaped out on.