My 2019 Can Am X3 RC started having the dreaded 'dtiveline rattle' even with the Can Am set screw fix. Grease was my only other option and I couldn't find a video on adding a grease zerk so I figured I'd just make one quick. Enjoy!
Пікірлер: 36
@Horton234 ай бұрын
Cutting fluid is your friend here, specially turning that bit that fast.
@4x4Play4 ай бұрын
You're absolutely right!
@304trails8 Жыл бұрын
I have the same issue. 2019 xrc as well haha. I was going to replace the entire drive shaft because I figured they were just wore but I never heard of that set screw solution before May try that and put a grease zero on like you did before I spend 400 bucks.
@4x4Play6 ай бұрын
I would try, it fixed my issue completely
@304trails86 ай бұрын
i went back to a factory carrier bringing recently after replacing my small shaft. it has minimal play still but you can only hear it at like 60 so im not mad about it haha. i think the easiest solution to this problem is to just replace the small shaft and the bearing and if you still have significant rattle your diff bearing is probably bad. @@4x4Play
@michaellorenzi45222 жыл бұрын
Hi, I’ve got a 2019 X3 Max. No noise yet, but I want to keep up on the maintenance. Did you have to remove the drivers seat to get that kick panel off?
@4x4Play2 жыл бұрын
Yessir
@michaellorenzi45222 жыл бұрын
Ok thx!
@DavidCook422 жыл бұрын
This looks pretty good. But does the grease move to the other splines? Or just where the fitting is.
@4x4Play2 жыл бұрын
Yep, spreads pretty evenly once you pump it in
@DavidCook422 жыл бұрын
@@4x4Play awesome thanks!
@jasonstull23752 жыл бұрын
Really wish someone would do a video of the sound so we can compare.
@4x4Play2 жыл бұрын
I didn't get the rattling on vid unfortunately, but it's very obvious. It sounds like a loose piece of metal rolling around
@danielt74486 ай бұрын
Did this fix the rattle I have the same thing maybe ? Sounds like a washer loose on a screw just bouncing around or something happens around 40mph goes away if you haul ass sometimes it’s louder then others can not find it for the life of me
@4x4Play6 ай бұрын
Yep totally resolved the problem, haven't had an issue since. Does your rattle go away when you run in 4x4?
@danielt74486 ай бұрын
@@4x4Play not sure I never checked that I will try today and let you know thanks fkr the video .
@willismartindale55693 ай бұрын
When it like rattle dose it seem like grind almost I’d feel it on the gas pedal mostly
@4x4Play3 ай бұрын
Yes, exactly. And mine was only in 2wd
@Randy_843 жыл бұрын
I get a rattling noise right around 40-45mph. Sounds like it's coming from the rear. Can't seem to find the issue.
@eddietrujillo2242 жыл бұрын
Yup exactly what mine is doing I have the 2022 sounds like if you have a bunch of pennies I a metal coffee can rattle from 40 to 45 I either gas it or slow down and it goes away shits annoying honestly but I can deal with it
@jasonstull23752 жыл бұрын
I have same issue it’s at a certain rpm around 25-30 mph if you hear it then let off throttle it gets loud then stops. I tried greasing splines didn’t go away. I have a hose clamp on exhaust springs and still there. Did you figure out what it was?
@ProGamerx2 Жыл бұрын
Same issue here with a 2022 with 300 miles on it.
@marcocontreras87 Жыл бұрын
Did you resolve the rattling noise issue? Mine is doing the same thing?
@NuclearT3acup Жыл бұрын
@@marcocontreras87 Check your seats. Mine had a rattle from a the seat bases. There are cutout areas of metal that touch metal on metal.
@RodJ2 жыл бұрын
rear one rattles like crazy.
@vongtaynhanaikptt60662 жыл бұрын
God's Blessing Berry Nice Video Upload
@4x4Play2 жыл бұрын
Thank you!
@imteggyyy89472 жыл бұрын
what size drill did you use?
@4x4Play2 жыл бұрын
It's going to depend on the size of the fitting you're going to use, but mine was a 1/4 hole I believe
@kbar6304 Жыл бұрын
Did it make much of a difference?
@4x4Play Жыл бұрын
Yes, completely eliminated the rattle, and now I can grease that yoke with ease
@welderteach2 ай бұрын
That’s a crappy deal. It’s going to wear. Basically if can am would have looked at the automotive industry they would see that most truck manufacturers use a Teflon like material on the splines and often a grease fitting on the slip yoke as well to prevent wear and possibly a rattle.
@4x4Play2 ай бұрын
Agree 💯
@Casperarizona Жыл бұрын
So I haven’t removed anything. You said you greased the back end. Could you add a grease fitting in the back also? Is there room for it?