CAN-BUS Explained | Everything You Need to Know About CAN-BUS

CAN-BUS Explained | Everything You Need to Know About CAN-BUS | CAN-Bus Diagnostics & How It Works

Рет қаралды 177,448

Automotive Diagnosis: Cars Repair &Training Guides

9 ай бұрын

In this video I explain what is the CAN-BUS, I explain different types of CAN bus including C-CAN (Powertrain CAN), M-CAN (Multimedia CAN) and B-CAN (Body CAN), I explain where you can find the CAN-BUS on the car, how control units are connected to CAN-BUS, I explain what the Gateway is, I also show you on the car how to check the CAN-BUS resistance, how to check the CAN-BUS voltage (with a multimeter), how to check the CAN-BUS for short to ground. I also show you how to read the CAN-BUS waveform using a picoscope.
Please also watch the following video about other networks on cars too:
CAN-BUS Explained (Part 2) | B-CAN Diagnosis | Test B-CAN with Multimeter & Oscilloscope:
• CAN-BUS Explained | B-...
LIN Bus Explained | Everything You Need to Know about LIN BUS | Local Interconnect Network
• LIN Bus Explained | Ev...
K-Line vs LIN-Bus | K-Line Explained:
• K-Line vs LIN-Bus | K-...
Join the channel for more videos and more support:
/ @automotivediagnosis
Please follow us on the following social media too:
/ autodiag001
/ automotivediagnosis
#canbus
#candiagogaming
Disclaimer:
Any information contained in this video is just the understanding of “Automotive Diagnosis: Cars Repair & Training Guides” and it is not an official guide or reference, so everything provided in this video is just a share of our experience and understanding and they are provided as a courtesy for your reference only. So, if you are using any part of this video, use the information at your own risk. We highly advise you to check the manufacturer owner’s manual before performing any act of removal, diagnosis, inspection, or repair on your car to know about what you are authorized to do on your car, what the correct and legal procedure is and what risks might be involved, also viewers are strongly advised to consult a licensed person before any sort of inspection or repair. Due to the factors beyond the control of “Automotive Diagnosis: Cars Repair & Training Guides”, we cannot guarantee against improper use of information or tools or systems, or the procedure provided. “Automotive Diagnosis: Cars Repair & Training Guides” disclaims any damage, injury or loss caused by your decision to follow the steps provided in this video.

Пікірлер: 221

@AutomotiveDiagnosis 7 ай бұрын

You can also watch the following video for LIN BUS: LIN Bus Explained | Everything You Need to Know about LIN BUS | Local Interconnect Network kzfaq.info/get/bejne/rMeEo5aa07qxlIk.html

@user-rc8qp5xs9o 3 ай бұрын

thank you so much for teaching .... I have a question.....how many volts must I get on these CAN WIRES on truck 24 Vts vehicle

@AutomotiveDiagnosis 3 ай бұрын

@@user-rc8qp5xs9o Hi there, CAN bus is a universal protocol with same specifications. The only thing is you must know what type of network is used on that specific car, so you will know the diagnostic procedure.

@onesaja10 2 ай бұрын

I hate wiring with Canbus,ITS not flexible for modify any electrical ITS not allow with Canbus,i like tradisional wiring ITS more simple to understand and flexible and compatible for other electric system' and easy to understand

@michaell1112 4 күн бұрын

This is video is absolute gold! Such great information and the way you present this information is very easily digestible for dummies like myself. Thank you for making this video you good man you!

@AutomotiveDiagnosis 4 күн бұрын

Thanks my friend. I'm glad you enjoyed it!

@mxmln8699 7 ай бұрын

I don’t really work with cars, but I’m an IT trainee. Watching this video was really informative, interesting and you explained everything very well. Thank you so much, I have always wondered how the can bus works exactly. Keep up the good work! And also now I understand why the ford focus of my sister in law was acting up with weird and seemingly unrelated error codes when the solder joints of her cluster broke.

@AutomotiveDiagnosis 7 ай бұрын

Thanks for watching the video and sharing your experience. I’m glad you enjoyed it.

@williamcasey6715 Ай бұрын

I have never seen a better explanation of the CAN-BUS, I am extremely grateful...!!!

@AutomotiveDiagnosis Ай бұрын

Thanks my friend. I’m glad you liked it.

@masoudahmadi9118 7 күн бұрын

داداش ویدئو فوق العادست دمت گرم ❤

@AutomotiveDiagnosis 7 күн бұрын

Thanks my friend.

@cennsa140driver 3 ай бұрын

Thanks, I started working on cars setting point gaps and using a timing light. Now I work on adaping modern engines into older vehicles. The overview was helpful.

@AutomotiveDiagnosis 3 ай бұрын

I’m glad you liked it 👍👍

@bandzar80 7 ай бұрын

Grate material. Don't stop doing this. Thank you👊

@AutomotiveDiagnosis 7 ай бұрын

Thanks my friend, more videos to come.

@jeffhong2135 9 ай бұрын

Very informative and helpful with clear explanations about Can Bus

@AutomotiveDiagnosis 9 ай бұрын

Glad you think so!

@rodp5919 6 ай бұрын

Thank you very much for the very informative video!! I learned a lot from you!! Keep up your good work!!

@AutomotiveDiagnosis 6 ай бұрын

Thanks for watching the video and supporting the channel

@halimabdul630 6 ай бұрын

Your explanation about can bus is awesome... ❤️❤️❤️ I got some new points from your this video. thank you...

@AutomotiveDiagnosis 6 ай бұрын

Hi my friend, I’m glad you enjoyed it

@foxythedirtydog4494 7 ай бұрын

Great info especially about the termination resistors.

@AutomotiveDiagnosis 7 ай бұрын

Glad it was helpful

@hamidelmziny2981 4 ай бұрын

thank you so much for information about k line

@AutomotiveDiagnosis 4 ай бұрын

Thanks for watching. You can also watch the following video for more information about LIN-Bus: kzfaq.info/get/bejne/rMeEo5aa07qxlIk.html

@bigstuff52 5 ай бұрын

Thank you for uploading..Very understandable video...

@AutomotiveDiagnosis 5 ай бұрын

Thanks for watching

@mzee5533 9 ай бұрын

This video has explained in details about the can-bus. Hope you keep on getting this type of important info from you guys.

@AutomotiveDiagnosis 9 ай бұрын

Thanks. I'm glad you liked it.

@paulitopa3375 7 ай бұрын

Thank you for this insight, looking forward to learning more

@AutomotiveDiagnosis 7 ай бұрын

Glad it was helpful!

@MiniBrothas 8 ай бұрын

Thanks for all this information! Really well done!

@AutomotiveDiagnosis 8 ай бұрын

Many thanks for watching

@robertszekely7293 Ай бұрын

Super video! Thank you!

@AutomotiveDiagnosis Ай бұрын

Thank you very much!

@isaacdarkey871 8 ай бұрын

You've really educated me on CAN BUS,thanks so much.

@AutomotiveDiagnosis 8 ай бұрын

I’m glad you enjoyed the video, more videos on CAN-BUS are coming soon.

@yuvarajaa5044 2 ай бұрын

Very nice explanation... thank so much and keep up the good work

@AutomotiveDiagnosis 2 ай бұрын

Thanks, I’m glad you liked it

@rebwarauto-technician2728 9 ай бұрын

well done, very helpful thanks for share it

@AutomotiveDiagnosis 9 ай бұрын

Glad it was helpful!

@gto3370 27 күн бұрын

Great video.👏👏👏

@AutomotiveDiagnosis 27 күн бұрын

Thanks for the visit. You may also watch the following video for B-CAN diagnostic: kzfaq.info/get/bejne/faqjes2Zs63Dqac.htmlsi=qtnimuGBioaDO7E3

@Steve.191 5 ай бұрын

Great explanation thank you 👍

@AutomotiveDiagnosis 5 ай бұрын

Glad you liked it

@stephensullivan9829 2 ай бұрын

I liked your video it has a good explanation for how the basics of this can bus system works. I was hoping that you might have an example of a failure or what really happens when one of these modules is bringing down the can and how you find out which one that is. I did need this though as i have very limited knowledge on a can bus system and working with electrical problems on a vehicle this could be helpful.

@AutomotiveDiagnosis 2 ай бұрын

Hi there, Thanks for your feedback. I actually didn’t want to make this video too long. There are more videos coming soon about CAN-Bus and hopefully what you mentioned will be included.

@abdoalbasha4368 9 ай бұрын

High explanations man .. thank you very much

@AutomotiveDiagnosis 9 ай бұрын

Thanks my friend, I’m glad you enjoyed it.

@mjb1552 28 күн бұрын

Im an EC engineer.I found your video information very useful as I have a 18 Accent, installed with a TS7 android player. I was looking for CAN bus to chose while configuring the Android system.I was not sure.

@AutomotiveDiagnosis 27 күн бұрын

Hi my friend. I’m glad it was helpful.

@weloveups831 6 ай бұрын

Good video, thanks!

@AutomotiveDiagnosis 6 ай бұрын

Glad you liked it!

@TurkVladimir 4 ай бұрын

Thanks Great Video

@AutomotiveDiagnosis 4 ай бұрын

Thanks for watching

@Raam08 6 ай бұрын

Great video brother ❤

@AutomotiveDiagnosis 6 ай бұрын

Thanks for the visit

@technocris1 8 ай бұрын

Thank you very much for initiating on CAN Bus communication !

@AutomotiveDiagnosis 8 ай бұрын

So nice of you

@GuySupa Ай бұрын

very good explanation

@AutomotiveDiagnosis Ай бұрын

Thanks 🙏

@ravigarage8745 8 ай бұрын

Perfect and well-presented

@AutomotiveDiagnosis 8 ай бұрын

Thanks

@sk13m11 8 ай бұрын

Bro thank you for that. You just simplified something intimidating

@AutomotiveDiagnosis 8 ай бұрын

I’m glad it was helpful

@elviscarey5270 8 ай бұрын

very detail thanks so much for sharing

@AutomotiveDiagnosis 8 ай бұрын

Thanks for watching!

@Singh-pu9wr 2 ай бұрын

EXCELLENT

@AutomotiveDiagnosis 2 ай бұрын

👍👍👍

@matmechanic5909 9 ай бұрын

Here is always a fan of your videos, thanks

@AutomotiveDiagnosis 9 ай бұрын

I appreciate that!

@G3R1PHONE 3 ай бұрын

amazing content .

@AutomotiveDiagnosis 3 ай бұрын

I'm glad you like it

@mohammadinamshah8370 9 ай бұрын

very nice explained sir

@AutomotiveDiagnosis 9 ай бұрын

🙏🙏🙏

@NoorAhmed-pu4yu 8 ай бұрын

Thanks sir for nice information about CAN system

@AutomotiveDiagnosis 8 ай бұрын

I’m glad you liked it 👍

@carlitoescarpe5740 Ай бұрын

Thanks for your effort to share you knowledge. I hope you can make a video on intire for ABS module specially in ford models. Thanks.

@AutomotiveDiagnosis Ай бұрын

Hi my friend. Thanks for watching. We already have two videos for ABS module repair on the channel, you can find them on the links below: kzfaq.info/get/bejne/obt3f5hk0LS8g3k.htmlsi=VY1ownUePjtqpuOX kzfaq.info/get/bejne/edWglZSB17KahX0.htmlsi=noPzx_WXHuMDbSJH

@ThunderbirdRocket 9 ай бұрын

Super helpful ! Thanks you !!

@AutomotiveDiagnosis 9 ай бұрын

Glad it was helpful!

@rashidselemani475 7 ай бұрын

Thanks you so much Sir for revealing the mystery 😊

@AutomotiveDiagnosis 7 ай бұрын

Thanks my friend for watching this video

@mohammadal-gebaly3046 9 ай бұрын

Excellent explanation , thank you very much , watching you from Egypt , it is really fantastic video , waiting for more videos like that, thanks a lot.

@AutomotiveDiagnosis 9 ай бұрын

Thanks a lot, I’m glad you enjoyed it.

@paulgreen2364 9 ай бұрын

Very helpful, thanks!

@AutomotiveDiagnosis 9 ай бұрын

Glad you enjoyed it.

@steveroff1178 3 ай бұрын

I tested according to what I see in your video but I do not see what happens if there is a short to power. When ohm testing 6 to 14 with the key off I get OL. Voltage on pin 6 is 10v and voltage on pin 14 is 8v. The van will not crank or start. The scantool can only communicate with modules on the low speed bus. It cannot communicate with ecm or tcm which are where the resistors are. I would suspect there is a short to power in one of the modules correct?

@romannevazno5147 9 ай бұрын

Great job. Thanks 👍

@AutomotiveDiagnosis 9 ай бұрын

🙏🙏🙏

@HariBuan 8 ай бұрын

Finally some good videos on youtube, thanks

@AutomotiveDiagnosis 8 ай бұрын

Glad you liked it!

@i.fix_iran6097 6 ай бұрын

good job man, thank you so much for your comprehensive and functional training. your accent says that you are Iranian, am I right?😁

@sohailahmed3101 9 ай бұрын

Fantastic sir. very exelent

@AutomotiveDiagnosis 9 ай бұрын

Thanks 🙏

@javidasgharzadeh413 5 ай бұрын

Great❤❤

@AutomotiveDiagnosis 5 ай бұрын

👍👍👍

@lucasellyson6872 6 ай бұрын

Great vid. Question though, in end of video you showed what a short to ground looks like on the pico waveform. But if you created a short to ground why didnt you blow a fuse?

@AutomotiveDiagnosis 6 ай бұрын

Hi there, thanks for the comment. There was no fuse issue because battery voltage is not provided directly to the CAN-Bus, so there is no fuse for the network, as voltage is provided through the CAN-Controllers inside the control units. So that short to ground will be detected by the CAN-Controllers and will change the mode to limp-home mode.

@linkbits1 7 ай бұрын

Thank you ….well explained 🎉

@AutomotiveDiagnosis 7 ай бұрын

Glad it was helpful!

@nickschuster7618 2 ай бұрын

I understand your talking automotive but in semis they use several datalinks and terminating resistors are inside of either a module or a starpoint. Example being on a New Cascadia on the powertrain CAN the terminating resistors are located within the CPC and the ACM. Within the PT CAN the MCM is part of the datalink but does not contain a terminating resistor. This is true for both Detroit and Cummins as far as my experience has shown me.

@AutomotiveDiagnosis 2 ай бұрын

Hi there, thanks for sharing your experience. Different companies tend to put the terminating resistors in different locations. Most of the times one of them is inside the ECM, and the other one could be inside any unit on CAN-Bus. For example I’ve seen the second resistor inside the BCM, Instrument cluster, interior fuse box and on some models I’ve seen an external terminating resistor as well.

@amarabdelli487 9 ай бұрын

Thanks for sharing

@AutomotiveDiagnosis 9 ай бұрын

Thanks for watching!

@TexasEngineer 6 ай бұрын

Please elaborate on the voltage on CAN HI and CAN LO. What is your reference? Are you measuring the voltage between the two CAN wires or are you measuring from the CAN wires to frame ground? Also, where does the power originate from to provide the voltage changes? Does each module require a 12 volt line and a ground for power?

@AutomotiveDiagnosis 6 ай бұрын

Hi there, voltage comes from each control unit as each unit connected to the CAN-Bus has got a CAN controller inside which regulates the BUS voltage and convert the signals to the CAN message format. For measuring the voltage on CAN-Hi, voltmeter red prob on CAN-Hi wire/pin, and black prob on body ground. Same way for CAN-Low but this time red prob on CAN-Low wire/pin. Ignition switch also must be on.

@autolovers3446 9 ай бұрын

I learned a lot, thanks

@AutomotiveDiagnosis 9 ай бұрын

Glad to hear it!

@junaidahmed8694 9 ай бұрын

great video👍

@AutomotiveDiagnosis 9 ай бұрын

Thanks

@user-be8rh6wk9k 9 ай бұрын

Very nice video thanks you sir ❤❤❤

@AutomotiveDiagnosis 9 ай бұрын

Glad you liked it.

@wesleywalsh4025 7 ай бұрын

I Like this video very much. Thanks for putting it together. 5 *

@AutomotiveDiagnosis 7 ай бұрын

Glad you enjoyed it!

@shayanvasseghi 8 ай бұрын

داداش دستت درد نکنه ویدئوی خوبی بود😁🙌

@AutomotiveDiagnosis 8 ай бұрын

Thanks for watching my friend.

@alaaalbudeiri1064 7 ай бұрын

Thank you very much it’s really helpful explain

@AutomotiveDiagnosis 7 ай бұрын

Thanks my friend, I’m glad it was helpful 👍🙏

@nw8000 6 ай бұрын

Great video can i ask what you call those probe converts are for the multi meter?

@AutomotiveDiagnosis 6 ай бұрын

Thanks for watching the video. They are called back prob pins.

@keithramdial512 2 ай бұрын

Can you show troubleshooting step for a can module ,thanks for all your great work

@AutomotiveDiagnosis 2 ай бұрын

Sure thing my friend

@dailytechytchannel7 9 ай бұрын

Thanks for the video

@AutomotiveDiagnosis 8 ай бұрын

🙏🙏

@giricyber-ps8420 7 ай бұрын

Thank you for the nice explanation and practical demonstration.

@AutomotiveDiagnosis 7 ай бұрын

Thanks for watching 🙏

@Tony-mg8eb 7 ай бұрын

Wow, very nice

@AutomotiveDiagnosis 7 ай бұрын

Thank you! Cheers!

@kicheollee7857 6 ай бұрын

Great video

@AutomotiveDiagnosis 6 ай бұрын

Thanks for the visit

@4m4s0 7 ай бұрын

Thanks for the information. But there was something I'm still wondering. How did you know that the A/C module was the Gateway? Is there any way to check that? Except for just testing disconnecting each module?

@AutomotiveDiagnosis 7 ай бұрын

Hi there, thanks for your comment. Mostly workshop manual or wiring diagram are very helpful for finding this kind of information.

@mauroaparicio1855 7 ай бұрын

great video

@AutomotiveDiagnosis 7 ай бұрын

Thanks for the visit

@hareethasrini41 2 ай бұрын

Hi,How do you say AC control and Instrumentation control alone is gateway.Can you explain how to intrepret that?

@AutomotiveDiagnosis 2 ай бұрын

Hi there. Normally gateway is connected between two different types of network. If you have multiple units connected to two CAN-Bus, that one which must be on the car in any circumstances is the gateway. For example, smart key control module is not a gateway as you may have a car without smart key. But instrument cluster is a must on the car. Also, workshop manual can help for finding the gateways.

@ilike2seeit 7 ай бұрын

Awsome!!! Thank you!!

@AutomotiveDiagnosis 7 ай бұрын

Thanks my friend, glad you liked it

@dipakmanu1842 8 ай бұрын

A new member is here, just joined the channel membership ‌‌😊 Thanks

@AutomotiveDiagnosis 8 ай бұрын

Welcome 🙏

@charleslyell3748 5 ай бұрын

Great video, thanks a lot. A question: can two modules communicate at the same time or not? Does one communication block another one until it's done?

@AutomotiveDiagnosis 5 ай бұрын

Hi there, thanks for the great question. In each CAN data frame, there are multiple fields, the second one is called “arbitration field” which decides the message priority. So if two control units are sending messages at a very same time, arbitration field decides which one has a higher priority. Therefore, the message with the highest priority will be sent first.

@charleslyell3748 5 ай бұрын

@@AutomotiveDiagnosis Thanks again.

@AutomotiveDiagnosis 5 ай бұрын

👍👍

@alexmessina3383 9 ай бұрын

HI there, congratulations this is one of the better CAN bus videos. If I can respectfully suggest something that you could clarify: you explained the gateway module purpose and that terminating resisitors. However, given that both the Nav-AV Modcule and the AC Module (M-Can) are connecteed to C Can, you did not make clear how to determine which module of the two is the Gateway. You simply just stated that it was the AC module. Same for the Smart Key Module and the Instrument Cluster (B-CAN).They are both also both connected to the C-CAN. How do you know that the IC is the Gateway. How do you determine that just be looking at the wiring diagram. Yes I understand you could unplug modules until you see 120ohms on the meter, but that is a very long way around requiring often a lot of work. thanks again.

@AutomotiveDiagnosis 9 ай бұрын

Yes, that’s right, it’s really important to know which unit is the CAN-BUS gateway. I simply knew that for this car that I presented because it was mentioned in workshop manual, I’ve seen this reference to the gateway sometimes in wiring diagram and sometimes in workshop manual

@alexmessina3383 9 ай бұрын

@@AutomotiveDiagnosis ok often it’s not identified unfortunately

@ncdave4life 8 ай бұрын

Unplugging modules until you see 120Ω on the meter would find the module which contains a terminating resistor. But, if I understand correctly, that isn't necessarily the gateway.

@AutomotiveDiagnosis 8 ай бұрын

@@ncdave4life Absolutely, terminating resistor is not necessarily installed inside the gateway.

@Alfon-hz8nw 7 ай бұрын

Amazing

@AutomotiveDiagnosis 7 ай бұрын

Thank you! Cheers!

@mohsenmohsen8514 9 ай бұрын

This video was exactly what I needed to understand the CAN network. Are you going to make any video about other types of CAN too?

@AutomotiveDiagnosis 9 ай бұрын

I’m glad you liked it. Yes, many more videos are coming about CAN-BUS.

@arttellama2408 8 ай бұрын

What I know is CAN bus is generic called CAN open. I worked in heavy equipment using CAN bus and same as what is applied to small car.

@AutomotiveDiagnosis 8 ай бұрын

@@arttellama2408 thanks for sharing your experience

@user-ii1un6fq3h 8 ай бұрын

Just subscribed 👍👍

@AutomotiveDiagnosis 8 ай бұрын

Welcome 🙏

@RivalRx 8 ай бұрын

Amazing video, thanks for sharing.

@AutomotiveDiagnosis 8 ай бұрын

Thanks for watching!

@Walopa_uie 2 ай бұрын

hellow sir i really like your video from Philippines,, sir how to know the pin out of any module or to access the module pin out, or a link...thanks your teaching us

@AutomotiveDiagnosis 2 ай бұрын

Hi my friend. Thanks for watching the videos. I think the following video will answer your question: kzfaq.info/get/bejne/aLtlZNiq1pjKmI0.htmlsi=iyunZjJ9TV2ueOjk

@samisulaiman7967 8 күн бұрын

thanks for explaining I have an issue on my Suburban 2012 , I got these code : P0700 Transmission control system ( MIL Request ) , U0073 Control Module Communication Bus "A" Off , P2635 Fuel Pump "A" Low /Performance from where should I start the solution thanks

@AutomotiveDiagnosis 6 күн бұрын

Hi there, normally if there is a major issue on CAN bus, there will be no communication between scan tool and that control module, I would start by checking the PCM connectors. Do you get any other simile fault codes in other control modules too?

@samisulaiman7967 4 күн бұрын

@@AutomotiveDiagnosis I appreciate thank you very much

@user-cz9lg4hq4r 8 ай бұрын

The best

@AutomotiveDiagnosis 8 ай бұрын

Glad you think so

@dhruvsingh2876 Ай бұрын

Well..If terminating Resistance is Inside ECU, doesnt it disrupt CAN communication when we remove ECU from the vehicle? But as we can see CAN system still works after Removing ECU?

@AutomotiveDiagnosis 28 күн бұрын

Hi my friend. CAN BUS is a multi-master network, so, removing a unit should not disrupt the entire network (although I have seen some cases that it does 😒). Anyway, removing the ECM or even a terminating resistor (in case of having an external resistor) will only make the network more noise sensitive and voltage fluctuation will put the other control units at risk, but network must still work.

@jeffmech5948 8 ай бұрын

Nice

@AutomotiveDiagnosis 8 ай бұрын

Thanks

@MAZHARKHAN-qy2ho 9 ай бұрын

Hii. I loved the Class. Pls, can u give us more video on Other CAN and LIN network. Thank u.

@AutomotiveDiagnosis 9 ай бұрын

Hi my friend, thanks for your comment. Sure thing, many more video are coming soon

@AbdulJabbar-hc8dq 9 ай бұрын

very easy

@rizzygeorge 2 ай бұрын

hi...i have some problem with CAN..car.is an Audi a6 c6 year 2010....i have no comunicațional with CAN and generator and batery module .....eror j533....have any idea were to look?thank you🍻

@AutomotiveDiagnosis 2 ай бұрын

As far as I remember, J533 is the CAN gateway integrated with instrument cluster. So not a bad idea to check it out.

@DavidGutierrez-zi4dy 7 ай бұрын

thanks.

@AutomotiveDiagnosis 7 ай бұрын

Thanks for watching

@GOMAND-4men 8 ай бұрын

super film.

@AutomotiveDiagnosis 8 ай бұрын

Glad you enjoyed it

@joveesmallwood9693 2 күн бұрын

👍

@AutomotiveDiagnosis Күн бұрын

👍👍

@renellhenwood3516 9 ай бұрын

Good stuff. What is FD CAN all about

@AutomotiveDiagnosis 9 ай бұрын

CAN FD (flexible data-range) is a new development to increase the bandwidth of the initial CAN-BUS protocol.

@pault4513 6 ай бұрын

My 1997 Dodge Ram uses a can bus for cruise control

@user-ef3rt1ef7i 2 ай бұрын

Resistors are to avoid reflects waves

@AutomotiveDiagnosis 2 ай бұрын

That’s correct, thanks for pointing that out.

@AASKAROFFICIAL 7 ай бұрын

Sir can lowcan high wire me voltage kaha se aata hai

@AutomotiveDiagnosis 7 ай бұрын

Hi there, there is a CAN controller inside each control unit which regulates the CAN voltage constantly.

@flip0x01 9 ай бұрын

Network looks like Hyundai. What data does the A/C module need or broadcast?

@amrelshennawy5792 6 ай бұрын

Plz where is location of can gateway module in kia cerato 2011 I have U0101 lost com. With TCM c-can u0001 high speed can com. Bus off c-can

@AutomotiveDiagnosis 6 ай бұрын

Hi there, gateway is the instrument cluster.

@djrigga 2 ай бұрын

Can bus works on priority it’s language is binary 0s and 1s and everything in the network speaks to each other weather 1 module wants to listen or not the signal passes down the line to where it’s relevant information is wanted

@AutomotiveDiagnosis 2 ай бұрын

Absolutely correct. Thanks for sharing your experience and knowledge .

@mwangigateiyu1570 7 ай бұрын

Do you have a video about k-line network

@AutomotiveDiagnosis 7 ай бұрын

I’m looking forward to an opportunity to make one. Hopefully soon.

@seanlevoy9446 8 ай бұрын

Yeah this is great and all, but when you cant start your car because the module for the rear lights is out, IDK. When you need to reprogram a turn signal module and you must go to the dealer.IDK.

@AutomotiveDiagnosis 8 ай бұрын

Yes, CAN-BUS is really great but it does have it's limitations and problems too.

@dailytechytchannel7 8 ай бұрын

How 1/60 becoms 60 ohms sir ?

@AutomotiveDiagnosis 8 ай бұрын

When you calculate the total resistance, as I explained in the video, the result was 1/R(total)=1/60 so as we want to calculate the R total, we change both sides of the formula to bring the R total and 60 to the top, so the result would be R total=60.

@dailytechytchannel7 8 ай бұрын

@@AutomotiveDiagnosis thanks sir got it

@hamzajaddour1797 8 ай бұрын

1/RT=1/60..….....then RT=60

@AutomotiveDiagnosis 8 ай бұрын

@@hamzajaddour1797 That's right.

@francismiranda7812 6 ай бұрын

How to red xf wireing diram

@AutomotiveDiagnosis 6 ай бұрын

You mean Jaguar XF?

@mistalobsta 7 ай бұрын

Well done champ. Nice flow to explanations. Terrible handwriting though. You must be a doctor in real life.. :) :D :p hahahahaha

@AutomotiveDiagnosis 7 ай бұрын

Thanks for your comment, sorry for the handwriting 😅, it’s normally not that bad, but for making this video I used a laptop which was not very easy to write on the screen.