Carve a Tapered Hole in Vectric VCarve and Aspire

Рет қаралды 40,576

3 жыл бұрын

Carve a Tapered Hole in Vectric VCarve and Aspire
More down here ↓↓↓ Click SHOW MORE!
In this video, I’ll show you how to carve two different styles of Tapered Holes in Vectric’s VCarve and Aspire software.
I’m going to demonstrate what dimensions you need to know to use the Moulding Toolpath to create a tapered hole, and how to figure out those dimensions. Next, I’ll demonstrate how to create the vectors to establish the boundary vectors and the profile. Then I’ll show you how to calculate the Moulding Toolpath and a Pocket Toolpath to cut the tapered hole through the piece of material. Finally, I’ll show you how to modify those vectors to create a tapered dish/bowl interior, instead of carving all the way through the material.
As usual, if you have any comments or questions about anything I covered in this video, please join me for the Live Q&A, or put ‘em in the comment section below.
On Sunday, January 24th, I’ll be hosting a LIVE Q&A session, where you can ask your questions pertaining to anything I covered in this video. That Q&A starts at 3 pm Eastern time, Noon Pacific time. I hope to see you there!
Here’s a link to the Live Q&A: • LIVE Q&A #75 - Carving...
______________________________________________________________________________
If you’d like to support my channel and help with the making of future videos, you can donate by using any of the following links:
StreamLab : streamlabs.com/marklindsaycnc
PayPal: paypal.me/MarkLindsayCNC
______________________________________________________________________________
Link to The Trampled Underfoot Podcast. "Two guys from different decades, backgrounds, and opposite sides of the continent discuss life, the universe, and everything. What's the show about? About an hour..."
KZfaq: / @trampledunderfootpodcast
Facebook Page: / trampledunderfootpodcast
Past Episodes available at our website: trampledunderfootpodcast.com/
______________________________________________________________________________
Link to the Vectric for the Absolute Beginner Playlist: • Vectric for the Absolu...
Link to the 3D Modeling for the Absolute Beginner playlist: • 3D Carving for Beginners
Link to the V-Carving for the Absolute Beginner playlist: • V-Carving for the Abso...
______________________________________________________________________________
Get your Official Mark Lindsay CNC T-shirts and coffee mugs here:
marklindsaycnc.com/index.php/p...
I’m a proud founding member of the Maker’s Media Network.
Come check us out at: makersmedianetwork.com/
marklindsaycnc.com is sponsored by Harneal Media - a website developing company that specializes in websites for the maker community. Find out more at:
harnealmedia.com/
______________________________________________________________________________
For more information on, or to download a free trial of Cut 2D, VCarve, or Aspire, visit the Vectric website at:
www.vectric.com/
______________________________________________________________________________
Some links may be affiliate or sponsor links. Purchasing or even clicking through these links helps with the making of future videos.
I appreciate your support!
This video is for informational and entertainment purposes only.
#Aspire #VCarvePro #Tutorial #Beginner #NotSponsored

Пікірлер: 123

@johnbourgeois6863 Ай бұрын

Thanks Mark - that was a great video ! I'm new to Pro Carve so exploring the possibilites is exciting(even starting at 73 years old as I am. Your pace of explanation, detail, is much appreciated.

@EdAgers110 17 күн бұрын

Extremely informative! I’ve seen your name pop up on Garrett’s videos and Wednesday evening live streams. Subscribed

@MikeHatalski 2 жыл бұрын

"With a closed toolpath, the Moulding toolpath will always project to the outside" Many thanks for explaining this!!!

@mdummy Жыл бұрын

The guideline tips were worth enough a watch! Great demonstration!

@bts6538 3 жыл бұрын

As always, very informative. Thank you very much Mark for what you do.

@loganmcdannell6870 3 жыл бұрын

Mark, thank you, all your videos have helped me at work tremendously.

@LusitanoPK Жыл бұрын

Such a good insight as to what can be done with more experience. Thank you Mark.

@johncalvey96 2 жыл бұрын

Awesome video just what I was looking for!! I made a few plates with carvings on them but the back of the dish was just round and 1/2" thick I never even gave them out because I knew their had to be a way!! Thanks Mark!!

@IceCreams62 3 жыл бұрын

Very nice to see millimeters in the top of the video :-) , thanks Mark

@richardpoulin2947 3 жыл бұрын

thanks Mark as always very well explained. I was going to email you for information on moulding tool path but you had all the answers for the problem I had in the projet I'm working on, in this video.!! And thank you for the millimeters too!

@mikeeudy7821 3 жыл бұрын

Awesome instruction! Just what I was searching for. CNC would be even harder for me if it weren't for your teachings. Thanks Mark!

@PeachCraft55 2 жыл бұрын

Thanks so much for doing this video it’s awesome and exactly what I’m after as I’m making shelves for an egg cupboard, can’t wait to see how it turns out. 😊

@MrRoscoj 3 жыл бұрын

Great tutorial! This is extremely helpful. Thanks you!

@UNKNOWNDIFFERENCES32 3 жыл бұрын

love the fact that you write the inches to metric :) keep adding this to your videos :)

@joeygonzo 3 жыл бұрын

very useful for speaker baffles. tapered rear of the hole is common for woofers to have some air clearance. GOLD!

@kjellt.evensen4811 Жыл бұрын

Thank you, Mark. Just what I have been looking for.

@Igorfun 2 жыл бұрын

Hi Mark, thanks for your enormous effort sharing your knowledge, you are a saint.

@onlyychevys 3 жыл бұрын

Awesome video Mark! Thank you!

@toolchuck 3 жыл бұрын

You are an awesome teacher Mark! I tried this with the “Draw Curve” tool to get a curved profile and it worked great! I overlayed it on top of the angled vector I created first as a guide for the start and stop points. I love learning VCarve, you make it easy to understand and most importantly, to apply it. Thank you, Mark.

@MarkLindsayCNC 3 жыл бұрын

Thank you very much! Keep working it!

@IDCWoodcraft 3 ай бұрын

awesome discussion on molding toolpath!

@almorrison6273 Жыл бұрын

Thanks Mark - GREAT instructions

@woodfantasy871 3 жыл бұрын

Awesome! Thank you for the "mm notes" sir!!!

@MrJortiz215 Жыл бұрын

Such a great video! Thank you!!

@darrellsaturnbigfoot Жыл бұрын

Whoa, thank you Mark. I can now build my dust collection reducers 👍👍👍

@robbie6625 9 ай бұрын

And they'll look far more professional than my idea of just doing nested round pockets of different diameters

@acrilicospubligar 3 ай бұрын

muchas gracias,eres el mejor.saludos desde chile

@seancorcoran5172 13 күн бұрын

Excellant tutorial

@cfodge69 9 ай бұрын

Super video, thank you.

@cfodge69 9 ай бұрын

Hi Mark, I need help with my settings. My inner circle is 1", my outer circle is 3", I want to cut out from the inner circle. How do I compute the angle? Material depth is 1" Thank you in advance.

@nickk7838 2 жыл бұрын

Thanks Mark, a very good tutorial, i like your videos. I learned a lot from you. Wouldn't it be more efficient running a profile "internal" to cut the internal circle rather than creating a pocket?

@woodbe5311 3 жыл бұрын

that´s a good way to make a wooden dish without a lathe :)

@ianwebster8597 Жыл бұрын

Hi there, You are teaching me (a complete newbie) a lot, thank you! A question. You say that it will always project out with a closed vector so you then split the circle into two halves. As al alternative why would you not have just left it as a closed vector and simply use the inner circle as the guide rail? Apologies if I am using the wrong terminology - as I said I am still really green at this.

@farmlender01 3 жыл бұрын

Excellent video Mark. Thank you . I’m looking to make a few “catch all” trays with this method. Would it be right to assume the molding tool path could be used with shapes like rectangles and stars?

@MarkLindsayCNC 3 жыл бұрын

It certainly can. Just experiment and preview often!

@JJ-wu4cv 2 жыл бұрын

Mark, fantastic video! I was stumped at how to make finger recesses to get a deck a cards out from a hole. One things I did notice, after I created the pockets per your video.....now all of my pocket cuts are tapered, even in new projects. Any ideas how to reset it to have a straight down cut?

@JJ-wu4cv 2 жыл бұрын

Scratch that, it was selecting three tools to make the pocket. Deleted the ones I didn't need and it cleared up

@firewoodsteel 9 ай бұрын

Hello Mark, how could I make a long socket holder. I would like them to be snug around them, keeping in mind some smaller sockets have that curve taper to the tip. Further on I would like to make it at an angle, meaning the bottom of the sockets are lower than the tip.

@cscheah5106 3 жыл бұрын

Hi Mark, why is that the (gap above toolpath) and (gap below toolpath) under "molding toolpath' setting can't be set to 'zero' as shown in the video? I select (gap below toolpath) and slide the slider all the way to the top... and a number will automatically fill in for me... it wont allow me to set to 0. thanks

@rufustoad1 3 жыл бұрын

Great video Mr Lindsay but a lot of work!! Would love to see you do this exact same on an elliptical design. Acts a lot different in my experience and it forces you to gap above or below toolpath which completely throws off your design. How do you stop that?

@garrydye2394 Жыл бұрын

100%. Ever get an answer to this?

@janetpersons8030 2 жыл бұрын

Can you teach us how to do this making a candle holder. Candles graduated large to small?

@lanebyron4097 3 жыл бұрын

Great video Mark. I had a tapered toolpath made for me in Aspire to cut 3" thick ash at 45 degrees. The tool ran a full 360 not half at a time. Do you know how that was done?

@MarkLindsayCNC 3 жыл бұрын

Not off the top of my head, Lane. There are 4 or 5 ways of doing it in Aspire, so there's no telling which way the person did it without having the file open.

@johns2926 3 жыл бұрын

Great video as I always learn a ton of useful information. For a smaller taper at 45deg, couldn’t you just use a 90deg V Bit instead of a ball nose to taper down to the smaller circle? Just a thought. I may be way off here. Thanks for sharing the knowledge!

@MarkLindsayCNC 3 жыл бұрын

That is absolutely an option, and it's probably the easiest way to go. But let's say the angle you need is 36 degrees. Unless you have a 72 degree v-bit made, you're stuck. But yes, your point is valid - I probably should have picked a different angle for the demonstration.

@johns2926 3 жыл бұрын

@@MarkLindsayCNC no worries. The technique you showed was valid and informational as I’ve never carved tapers and something I’ve been interested in doing here soon. I was just thinking a bit. Using a VBit, would the moulding tool path be the best option or would you recommend a different technique? Btw I’m using VCarve Pro. Thanks.

@MarkLindsayCNC 3 жыл бұрын

I'll discuss it more during the live Q&A, but you could pocket out the bulk of the material, select the bottom diameter vector, and do a Profile toolpath, machining ON the vector. And thinking about things like this is always a good thing. That's how we progress. It's one thing to say, "Do it this way," or "Don't do it this way." It's another thing to figure out why.

@tbunton2928 3 жыл бұрын

I'm guessing we can somehow use this technique on outer profile tool paths as well? ...instead of applying draft to model. I'm not sure the result would be any different though but something to think about. Thanks Mark!

@MarkLindsayCNC 3 жыл бұрын

Adding draft to a model is not an option in VCarve, and the question I got was specifically about doing this in VCarve Desktop. Yes, you can add draft to a model in Aspire to get the same result. Actually, I can think of about 4 different ways of getting the same result in Aspire, but almost all of them aren't available in VCarve. As for doign this on an outside profile, just don't split the vector and the Moulding toolpath will project to the outside. Boom - done.

@DanWrightPerl 3 жыл бұрын

This is useful information. Thank you for doing it. You have a lot of good tips in there. But I don't think you needed to take a whole half-hour to present this information.

@MarkLindsayCNC 3 жыл бұрын

Actually, comparatively speaking, this is one of my shorter videos. It doesn't take me a half hour to do it on my own, but try this - draw 2 projects, and explain every step along the way as if you were showing someone who had never done it before. Time yourself doing that. You'll be surprised at how long that actually takes. And remember that I edited the video - it was longer before I did that.

@robertyack1661 17 күн бұрын

The time Mark takes is exactly why he's a good teacher. For people early on in their journey, his detail is perfect.

@TheWoodFly 3 жыл бұрын

HI Mark. Good vid: A couple questions. 1) Using Guides vs. a square. If I knew I needed a 1/2" diagonal line, why not draw a 1/2" square and then a line from one corner to another? Seems like fewer steps then dragging and offsetting 4 guide lines. 2): why not select the inner circle, reverse the direction of the profile vector and make the swept profile rather than cutting apart the outer circle? Thank you.

@MarkLindsayCNC 3 жыл бұрын

Thank you! The reason I used guides in this video was to reinforce their use. I'd had a lot of questions about using guides prior to making this video, so I decided to use them for this demonstration. You absolutely can use a rectangle to get your angle. The reason I didn't use the inner circle was to avoid potential damage to the bit or the machine. By selecting the inner circle and sweeping that profile upward and outward, that means your bit is going to move over to that inner circle, plunge in the full thickness of the material, then try to carve it's way up and out of the trench it just dug in one pass. A good percentage of CNC routers can handle that, but a bigger percentage of home/hobby CNC routers can't. Additionally, depending on the bit you're using, the bit may not have enough cutting length to be able to cut the full thickness in one pass. This is especially true with smaller diameter bits. If you try to cut material that's thicker than the cutting length of the bit, you WILL snap it off. I addressed both of these questions in Live Q&A #75, which followed the video, the day I released it. If you'd like to check out that Live Q&A, here's a link: kzfaq.info/get/bejne/idSdlLZyptiucZc.html

@user-pp6gi3rx6h 7 ай бұрын

Can you use a sweeping curve instead of a straight line?

@bobmann107 3 жыл бұрын

Thanks for helping us all out. Curious tho...instead of the trick with the guide lines (which I was unaware that you could create additional guide lines, so thanks for that!), why did you not draw a square with .5 sides and then draw the diagonal? It is less clicks.

@MarkLindsayCNC 3 жыл бұрын

I did that mainly to reinforce the use of guide lines, as I've had a few questions about them as well. I certainly could have drawn a rectangle (and I almost did,) if I knew the diameters of the top and bottom holes. Having one diameter and an angle would have made it a bit more difficult, but not impossible. It's an option, and you could certainly do it that way. There are usually several ways of achieving the same goal, and any way you choose that gives you the result you want is certainly valid.

@bobmann107 3 жыл бұрын

@@MarkLindsayCNC understood, I just wanted to make sure there was no other reason. Thanks for responding!

@Michaelsmith1952 3 жыл бұрын

Just wondering if using a profile cutout for the center instead of the pocket would be less wear on the .250" end mill?

@MarkLindsayCNC 3 жыл бұрын

You certainly could use a Profile toolpath. You have to figure a way to secure the center piece to the table (tabs, tape and CA glue, or whatever,) but it's a viable option.

@ionbuilds 2 жыл бұрын

Mark is it possible to make a 45 degree angle hole with v carve?

@curtistidwell5601 Жыл бұрын

Drilling tapered hole my rail first profile next but want put lines around circle

@epeleg 3 жыл бұрын

Great video as always Mark. Interesting that the resulting tool paths (circa. 18:40) are using both normal and climb milling - was this intentional ? can this be avoided (i.e. make it go clock wise or CCW in both halves ? From the second example (i.e. without cut through) I understand that the inner circle is actually not used for anything... Also would I be right to assume that you are not limited to a straight line and you could use the same method to create an ogee style cut without the need for an ogee bit (and probably also not limited to a circle for the guiding path...)?

@MarkLindsayCNC 3 жыл бұрын

I hope I answered your questions satisfactorily during the Live Q&A, Eyal!

@epeleg 3 жыл бұрын

@@MarkLindsayCNC Very much so, thanks.

@ronald44181000 3 жыл бұрын

Now that you've showed us all who to go about it on a Flat Plane, how about showing us how to do a Taper on a 4th Axis. I've tried it about a dozen ways from Sunday and can't for the life of me figure out how it could be done in VCarve though it is pretty simple to do in Aspire.

@MarkLindsayCNC 3 жыл бұрын

Carving a taper in VCarve is pretty tricky, no matter what. Let me work on it a bit, and when I get it down, I'll certainly post a video on it. There's a lot of bad info on the internet, and I don't want to add to it by suggesting something I haven't done myself. I'd rather make sure it works before I make a suggestion.

@acerjuglans383 2 жыл бұрын

What types of things have you done with this procedure Mark? I'm assuming there is more to be had than just making countersinks for screws.

@MarkLindsayCNC 2 жыл бұрын

This video was a direct answer to a specific question a friend asked me. Having said that, I have used it to make grab handles in drawer faces, and a recess on the bottom of a cutting board that will allow you to put a plate underneath and catch meat juices.

@emanuelortiz3667 Жыл бұрын

Hi. Can this be done on a rectangular shape?

@ElCidPhysics90 Жыл бұрын

To save wear and tear on the wide bit, could you have done a profile path yo the inside of the inner circle then remove the interior?

@MarkLindsayCNC Жыл бұрын

You would have to find a way to hold that inner piece so it didn't come loose when you cut it out. You can't use tabs in the Moulding toolpath. That's why I pocketed it out.

@ElCidPhysics90 Жыл бұрын

@@MarkLindsayCNC caveat I haven’t even purchased a cnc machine yet. Still evaluating the landscape and trying to find the courage to tell my wife I want to start a cbc business, lol. Thank you for your reply

@antonstayduhar8748 Жыл бұрын

You mention the molding toolpath always projects outward with closed vectors. Why does the closed vector need to be cut in two places rather than one? One cut vector is an open vector. And yes, as mentioned in reply to another comment, in this case a 45 degree bevel bit does the job efficiently (of course only for 45).

@eross21 11 ай бұрын

so i have a question. how do i make a tapered pocket? i basically want to make a square pocket with the floor of that pocket has a shallow end and deep end. ? i can’t figure out how to set it up i. software?

@derekjenkinson8014 Жыл бұрын

Why for hogging out the circle, did you not select a profile cut and cut inside the profile, rather than pocketing it out. Seems to me your method would take a lot longer. Learned how to do tapers though, so thank you for that.

@MarkLindsayCNC Жыл бұрын

Either way will work, Derek. Just know that using the Moulding Toolpath does NOT create a 3D component that you can attach 3D tabs to. Yes, you can create tabs with your Profile toolpath, but the minute you run that Moulding toolpath to create the taper, the tool is going to cut through those tabs. So if you use a Profile toolpath, make sure you have a way of securing the waste material in the center of your tapered hole. That's why I used the Pocket toolpath - to eliminate that possibility.

@derekjenkinson8014 Жыл бұрын

@@MarkLindsayCNC mank thanks for the reply and explaination of your reasoning. Cheers

@nathangold9775 Жыл бұрын

Seems like using a 90° V-bit instead of ball nose might yield a smoother surface with this profile?

@MarkLindsayCNC Жыл бұрын

The purpose of the video was to show how to create a taper with the Moulding Toolpath. To do that, you should use a ball nose bit, much like a 3D carve. Still, there are many ways to get the job done. If you can do it with a 90° v-bit, and have one big enough, by all means, go for it.

@kristianolauson4494 4 ай бұрын

Can you create more of a profile vs straight angle?

@EdAgers110 17 күн бұрын

Yes. Keep the initial profile line on your 2-D model until you draw your new profile so you will know where the start and end points are and connect your new profile to it, then delete it. It will work just like you are thinking

@SuperBulegila 3 жыл бұрын

Can you make spoons on the CNC using this method.

@MarkLindsayCNC 3 жыл бұрын

I would imagine you could, but I've never done it. Experiment and see what you come up with!

@thefilthelement 2 жыл бұрын

I'm trying to get this to work from a square to a circle for a custom shower pan but can't get it to cooperate 😢

@user-bw5xf3yr3m Жыл бұрын

What’s the difference between chamfer and taper???

@MarkLindsayCNC Жыл бұрын

A taper is a gradual reduction in thickness along a specific length. For instance, the entire surface of a piece of material can taper from .75 inches thick to .5 inches thick. A chamfer is an angle cut along an edge of a piece of material. It doesn't have to be to a specific depth.

@whitetailhollowacres6917 3 жыл бұрын

Hi Mark, I am wanting to do a blank dish in a piece of wood. I can't seem to find what I am looking for on youtube. Is there an easy way to do this? I'm thinking 3" in diameter and 1/4" deep. It seems like it would be so easy, but I can't figure it out. Can you help me? Thanks, Paul

@MarkLindsayCNC 3 жыл бұрын

If you check out my video on creating a 2-sided dish, you'll find what you need. The difference will be that you won't need to set up a 2-sided job, and you won't need to worry about the second model for the bottom of the dish. Just focus on the Top side of the project in the video; set the diameter of the dish, draw your Vector Boundary, set the Shape Height of the dish, add a Zero Plane, and calculate the toolpaths, machining to the Vector Boundary. Preview and make changes if you need to. Here's a link to the 2-Sided Dish video: kzfaq.info/get/bejne/g5p6gbB-rJu9fGQ.html

@dsaworxcarpentrysolutions9155 2 жыл бұрын

👍

@JasonNeri Жыл бұрын

Could this also be done by cutting the bottom hole with a straight bit and then using a vcarve bit centered on the line at full depth? Or some sort of combination?

@MarkLindsayCNC Жыл бұрын

Yes - to a point. You could easily do this with a combination of a Profile or Pocket toolpath to clear out the center of the hole, then a Chamfer toolpath to create the tapered side. The Chamfer toolpath was not available when I recorded this video. The thing to remember is that by using the Chamfer toolpath, the angle of the taper is limited to the v-bits you have.

@JasonNeri Жыл бұрын

Ok cool, I'm just learning on a machine lately and was trying to figure out ways to do this. I figured if you don't need a specific angle or if the angle is the same as what you have for a v bit, then you can do it that way. This is a really cool tutorial for it though, much more control of all the things.

@driftergw 3 жыл бұрын

Mark: Instead of breaking the outer circle into two vectors to get the toolpath to carve inwards, could you have selected the inner circle as the drive rail? Then, it would have carved outwards toward the outer circle, yes?

@MarkLindsayCNC 3 жыл бұрын

Yes, that is an option, Grant. The problem is you're now starting at the bottom and tapering outward and upward. That means for the first steps of the taper, you're machining away the entire thickness of the material at once. Is your machine capable of doing that in something like hard maple? Bit clearance also becomes an issue. What I mean by that is, depending on the tool, there may not be enough cutting length on the tool, or the collet may be in danger of crashing into the material. If the machine and tool is capable of cutting the entire thickness of the material, and there's plenty of clearance, then yes, you could project the toolpath up from the bottom hole.

@driftergw 3 жыл бұрын

@@MarkLindsayCNC I should have thought of that, duh! That's why they pay you the big bucks, Mark. :-) Tks much.

@MarkLindsayCNC 3 жыл бұрын

No worries, Grant. That's one of the hardest parts of doing this as a hobby - thinking ahead to the machining process before you even have the design drawn. Most folks in an industrial or production environment are used to doing that (with a few exceptions,) but as hobbyists, we tend to focus on one thing at a time. I mean, we can draw anything we want - now cut it in the real world. Sometimes it just doesn't work. Just mounting the piece you want to carve is a challenge at times, and sometimes what we want to do just isn't possible on a home hobby machine. Now, where do I sign up for those big bucks? lol

@squidskunk 3 жыл бұрын

mark im a "by hand" sign carver...new to cnc...when i hand rout a sign by hand i often need to create the illusion of depth by carving shallow in the foreground or bottom of a sign to a deeper depth to the background of the sign... as i learn how to create my layouts in aspire i find i cant see obvious way to increase the depth of the tool paths linearly from shallow cut to deeper cut from front to back in depth...how can i tell aspire i want all the tool paths the fallow a set linear depth from shallow to deep as i decide appropriate...?

@MarkLindsayCNC 3 жыл бұрын

That's something I'd not thought about. Are you looking for a tapered appearance as the carve transitions from the foreground to the background? Let me consult with a couple of my gurus and see if they have any input. I think I may have an idea or two, but I'll need a bit of time to make sure it works before I commit to saying it can or can't be done in the software. (I'm sure it can - I just need to confirm a couple of things and draw a few designs to dial in the process.)

@squidskunk 3 жыл бұрын

@@MarkLindsayCNC thank you mark...:-)

@JimHaysTechGeek Жыл бұрын

I do have a question. SInce you are cutting a 45 degree hole shouldn't you use a 45 degree V-bit? Just thinking out loud.

@MarkLindsayCNC Жыл бұрын

You could do that, yes - but suppose you want an 18° taper. The purpose of the video was to show how to carve a tapered hole in VCarve Desktop and Pro at basically any angle. I just used 45° as an example that everyone could relate to.

@wolfman1493 Жыл бұрын

Could you use a cove bit or a bowl bit guess they are similar bits

@MarkLindsayCNC Жыл бұрын

I've not tried it, but I don't know why it wouldn't work. Give it a try, but make sure to preview it to see if you get the result you're looking for.

@wolfman1493 Жыл бұрын

Almost worked with bowl bit im doing a heart but the bottom and top over lap and leave ridges i can live with the ridges as it gonna be filled with wax for candle but the bottom is out of wack trying to figure out that now your tutorials are great

@wolfman1493 Жыл бұрын

got it had to move the nodes wouldnt have got this without your help keep up the great work

@MarkLindsayCNC Жыл бұрын

Glad to hear you got it sorted!

@garrydye2394 Жыл бұрын

But.....But...Mark...what if your circles are not actually circles and irregular shapes? And therefore you do not have a consistent width of slope all the way around the tapered hole? Been driving myself crazy trying to find a solution to that riddle.

@MarkLindsayCNC Жыл бұрын

That's where you get into 3D modeling territory, which was outside of the scope of this video. For that, you need to do a 2-rail sweep (Aspire only.)

@garrydye2394 Жыл бұрын

@@MarkLindsayCNC Been trying that...can''t get it to work but thank you for the reply Mark.

@BeaulieuTodd Жыл бұрын

For a 45 degree, why not use a v bit?

@MarkLindsayCNC Жыл бұрын

The purpose of the video was to show how to create a taper. The angle is irrelevant. I could have chosen 50° just as easily, and the process would have been the same.

@jonathancazzella2437 7 ай бұрын

Buonasera mi scusi se scrivo in italiano se scrivo in ita italiano se vuole posso tradurlo. Io avrei bisogno di fare la stessa lavorazione però a forma di cuore mi può dare qualche dritta su come farla, perché ho provato ma non riesco, oppure se ha qualche video dove viene spiegata mi farebbe piacere. Saluti Jonathan Cazzella

@bigmac1598 3 жыл бұрын

I thought originally the board was 1" thick. Any angle diagonally across a SQUARE is going to be 45°

@creativebobbo Жыл бұрын

Once again Mark Lindsay to the rescue LOL but true

@sumetlerdmueng6123 Жыл бұрын

แล้วเส้น แรกทำเพื่ออ่ะไร?

@greedo-diedforusall 2 жыл бұрын

Instead of using a pocket tool path to remove the hole why not just profile tool path? That way you only have the cut time to cut one single internal outline to remove all that wood instead of hogging it all out.

@MarkLindsayCNC 2 жыл бұрын

Yes, you could use a profile toolpath. You'd need a way to secure it so it doesn't come loose after cutting it out, but that's not too difficult. There are many ways to accomplish the same end result. The purpose of this video was to demonstrate cutting the taper. How you deal with the waste in the center is your choice. Personally, I tend to pocket out the waste (depending on the size of the hole, of course) so I don't have to deal with trying to secure it to the spoilboard somehow.

@PeachCraft55 2 жыл бұрын

Hi Mark I’ve sent you a PM on Facebook

@MarkLindsayCNC 2 жыл бұрын

I'm sorry, Sue, but I never got it. I'm not on Facebook much at all. I'm rarely at my computer, as I have a ton going on behind the scenes.

@sueadams7165 2 жыл бұрын

@@MarkLindsayCNC I was having a few issues with numbers.