Explanation and demonstration of how the Lee Precision case trimming system works.
Пікірлер: 25
@noelarbuckle14702 жыл бұрын
Just a word of advice,, Don't spin your drill at full speed when cutting the shell. A slow speed is all that is needed. It will save your cutter from getting dull.
@dc9mm25 жыл бұрын
Just getting into reloading rifle. thanks for the help. nice video.
@dannie31173 жыл бұрын
Well done video. That is a neat tool
@RunGun9 жыл бұрын
Nice glad to see you back
@HereToLearn4429 жыл бұрын
Thanks for the support.
@Mr.Big-Gunz2 жыл бұрын
Nice video, i enjoyed it, just a tip the old type Lee Ball cutter is much easier to grip than that small cutter,& it's very reasonably priced, it's essentially the same cutter you're using but it's mounted in a comfortable round wooden ball that's way easier to grip and hold, midway usa sells them at a low price...
@artois89083 жыл бұрын
I was going to buy one of these but what a palava to do one case! My lee quick trim does the job in seconds on my press without any of this fuss.
@murrayandru75276 ай бұрын
I use a DREMEL HSES-01 and does it ever work SLICK at trimming FYI Dremel Cordless 4V USB Rechargeable Electric Screwdriver
@rpwattee6 жыл бұрын
What size does this actually cut them too
@TE300_Tim6 жыл бұрын
it cuts it to the SAAMI spec trim length
@roberttice4 жыл бұрын
I just bought this for 7mm rem mag. I can't get the cutter to screw all the the way into the gauge. Should I use pliers. I don't want to force it.
@roberttice4 жыл бұрын
@@tjvohs1 I used pliers and put it on and off a few times had gunk on threads
@michaellankford83586 ай бұрын
Be careful...grab the rod in narrow recess...grabbing the rod will leave burros that will hang up in case neck
@oosmanch13 жыл бұрын
Hi, I have noted I cannot insert the trimming rod into the neck once the neck has been resized, that's a shame as I prefer to use the cutter after neck resizing.
@martinlabuschagne3205 Жыл бұрын
i olso find the same problem with some cases i asume it is the thickness of the bras just press harder it will work i olso don't use drill according to me it wobble and make the neck bigger
@nerveangel16666 жыл бұрын
How is your drill mounted?
@HereToLearn4426 жыл бұрын
In a vise.
@skoeloc6260 Жыл бұрын
Where can I get that tool
@trimble423 жыл бұрын
Modulate? Moderate?
@dannie31173 жыл бұрын
Modulate= speed moderate= pressure
@bjornefellhanded97084 жыл бұрын
I'm only just getting into reloading and having to assimilate a metric f-ton of data. From the case trimmers Ive seen - this is a bloody awful way to go. Theres so much movement in the brass. Hell, maybe I'm over thinking it but the others seem positively stable by comparison.
@bobwoods50173 жыл бұрын
You're doing it wrong? Been years may be you figured It out?
@bjornefellhanded97083 жыл бұрын
@@bobwoods5017 To paraphrase myself - I'm learning - or did you miss that bit? Still, each to their own. I settled on the precision of L.E Wilson and that works for me. Whatever works for you. Would I do it this way? No. That doesn't mean its not suitable for others.
@randybichsel42446 ай бұрын
Why not just get an RCBS 3 way trimmer bevel taper tool much easier and less time consuming.