Chinese Diesel Heater Error Codes E01 - E10 All Codes, Faults & Fixes

Рет қаралды 255,106

Van Life Uk A Complete Survivors Guide

Күн бұрын

00:00 - Intro
00:15 - ERROR CODE 01
01:25 - ERROR CODE 02
01:49 - ERROR CODE 03
02:16 - ERROR CODE 04
02:36 - ERROR CODE 05
03:00 - ERROR CODE 06
03:47 - ERROR CODE 07
04:33 - ERROR CODE 08
06:41 - ERROR CODE 09
07:22 - ERROR CODE 10
ERROR CODE 01
This is a low voltage error code that can be caused by a few things
Low battery - Charge battery
Volt drop - Wire heater direct to battery via inline fuse and if you need to extend your power cable to reach the battery use 6mm2 cable.
As an Amazon associate, I earn from qualifying purchases.
6mm2 RED CABLE - amzn.to/35sLpGS
6mm2 BLACK CABLE - amzn.to/3kbNGdD
Controller set to wrong voltage - Check it is set to 12v not 24v in menu settings. password 1688
Damaged battery - Replace battery
DECENT AGM LEISURE BATTERY - amzn.to/3iFjiJy
ERROR CODE 02
This is a very simple one to explain, error code 02 is a high voltage error code.
Check that your 240v to 12v transformer is set to 12v if you are using one
Make sure your batteries are wired in parallel rather than series if you have multiple batteries.
ERROR CODE 03
This is a glow plug error code so most likely replace your glow plug
As an ebay partner I earn from qualifying purchases
REPLACEMENT GLOW PLUG - ebay.us/nbxWwp
GLOW PLUG REMOVAL TOOL - amzn.to/3iD2KBb
REPLACEMENT GLOW PLUG MESH - ebay.us/QRb3Hl
It could also be a battery with damaged cells - Replace battery/batteries
ANOTHER DECENT QUALITY AGM BATTERY - ebay.us/Ie4Ic7
ERROR CODE 04
Bad connection - Check all connectors are clipped into place correctly, check the pins inside make contact
Stuck piston - Give the pump a light tap a few times on start up
PUMP REPLACEMENT - amzn.to/3zusFSX
ERROR CODE 05
This is an overheating error code
Heat outlet - check that there is nothing obstructing your vents
Ducting - Check for blockages, harsh bends and that nothing has crushed it in
Fan side of heater - make sure there is a gap for the heater to suck in cool air, if there isn't enough cool air flowing over the heater it will overheat
ERROR CODE 06
This is a fan error code
Fan - make sure nothing is lodged in the fan
Fan - make sure the casing isn't pushing against the fan restricting it
Fan - make sure both magnets are firmly in place
Fan - poor build quality, send it back for replacement
TRICLICKS 5KW - amzn.to/3i3ti06
AMBIENCO 2KW - amzn.to/3qnAIfl
ERROR CODE 07
Broken controller - replace controller
BLACK 5 BUTTON REMOTE - ebay.us/1R3CDy
BLUE 5 BUTTON REMOTE - ebay.us/YvkRcN
BLACK 3 BUTTON REMOTE 2KW - ebay.us/eOwfnc
Incompatible controller - replace controller and motherboard
Bad connection - Check all connections of the blue cable that runs from remote to motherboard. even the solder on controller and motherboard or replace all
3/5KW MOTHERBOARD - ebay.us/81L6IE
2KW MOTHERBOARD - ebay.us/vqg5nL
WIRING LOOM 3/5KW - amzn.to/3qUXzzY
WIRING LOOM 3/5KW CHEAP BUT LONG WAIT FROM CHINA - ebay.us/IGJ0hz
ERROR CODE 08
This is a fuel system fault
New install - The heater needs priming before starting it
Run out of fuel - Make sure you have not run out of fuel, if you have you will need to prime the heater again
Low on fuel - If you have tapped into vans fuel tank and van is LOW on fuel fill it up
Air bubbles in line - Check pump angle, loose fuel clips, don't drive with heater running, change to the correct fuel line
DECENT FUEL LINE - ebay.us/8gA1HU
ERROR CODE 9
This is a faulty sensor code
Faulty sensor - Replace sensor
OVERHEAT SENSOR REPLACEMENT - ebay.us/exgTMT
We have also heard stories of the heat sensor not fixing the 09 error code and the actual thing that did fix it was a new controller for some reason. So if the heat sensor does’t fix the problem try a new controller.
Please see above
ERROR CODE 10
This is a multiple failed attempts error code
So any of the above more than one time, most likely EO8
or
Flooded - blow into air intake when the heater is starting up
IF YOU WOULD LIKE TO BE ENTERED INTO OUR MONTHLY VAN LIFE PRIZE DRAW WITH SOME AMAZING VAN LIFE PRIZES PLEASE SUBSCRIBE TO OUR BRAND NEW PATREON ACCOUNT FOR £3 A MONTH. YOU WILL AUTOMATICALLY BE ADDED TO THE PRIZE DRAW EACH MONTH...
/ vanlifeuksurvivorsguide
JOIN OUR DIESEL HEATER FACEBOOK GROUP
/ 212813887001237
CHECK OUT OUR BLOG
www.vanlifeuksurvivorsguide.c...
FOLLOW US ON FACEBOOK
/ van-life-uk-the-comple...
FOLLOW US ON INSTAGRAM
/ vanlifesurvivorsguide

Пікірлер: 416

@johndavis8655 2 жыл бұрын

A concise and well presented video giving valuable information without the poor sound quality, blurb and waffle often found in similar video's I've seen.

@StevenLucasMarketing 2 жыл бұрын

If only the supplied instructions were this clear.

@maxthecherryman 11 ай бұрын

Thank you. The clearest explanation yet of error codes. Yes E8 was my daemon and removing the supplied fuel filter made an immediate improvement with a slightly smoky start ( first time )no E8 error after 2 minutes so far and running ok so far been going for a couple of hours no issues. Closed down correctly.

@brownbunny2513 2 жыл бұрын

December 7th 2021 One year & one month since I brought my chinese diesel heater, I went to turn it on , and heard "Click", with no heat, no sound, no light on the controller. I am saying all this to say "Thank You",for making this video.. After watching your video, and a few checks with a multimeter I figured out that the controler was gone. I did as you recommended and brought another diesel heater.( cause just the ECU, may cost more than the whole heater) With alot of praying and patience I got the plugs to fit into one another, installed the ECU, and changed the controller. The controller has to match the ECU, or you'll get the E-07, code. Thank you!

@pm3577 4 ай бұрын

No waffling straight to the point tutorial. Brilliant. 👍

@guidelineuk4876 Жыл бұрын

You're an absolute lifesaver everyone else is trying to tell you about the cat dog garage etc ..your straight to the nice one subscribed

@elbybrook9466 Жыл бұрын

Thank you. I'm getting my heater ready for winter and I received a few codes and didn't know what they were. Watch your video and it answered all my questions.

@WarthogARJ 2 жыл бұрын

Thanks, well made video. Especially listing where the codes are in the video. Makes it very easy to get info from.

@paulbrown521 2 жыл бұрын

Brilliant explanation , no messing , blurb ,or crap ,Thank you .

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate and no problem you are welcome

@reacohn751 2 жыл бұрын

Cracking video with great no bull explanations and demos of appropriate areas. Nice one.

@raykeogh1972 2 жыл бұрын

Brilliant very informative video. Oh I have had overheating sensor on a few times and after watching this this now think it’s the bend in the airflow to distribute the heat around the van. Bad planning on my behalf. Thanks again Ray K UK YNWA

@lavaner-WeManufactureComfort 2 жыл бұрын

The most comprehensive and clear instructions video I have ever seen👍

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate, glad you liked it!

@cassandrasheridan7346 2 жыл бұрын

really helpful in time of need. Thank you for a genuine public service video 👍

@vanlifesurvivorsguide 2 жыл бұрын

No problem, glad you like it

@paulscussel140 2 жыл бұрын

Best explanation of error codes I've seen, thanks for sharing!😃

@scottjones9602 2 жыл бұрын

Excellent and comprehensive video, definitely one to keep for future reference. 👍

@vanlifesurvivorsguide 2 жыл бұрын

thanks scott

@karenjackson5733 2 жыл бұрын

I may need to save this for future reference!

@user936 Жыл бұрын

I'm currently playing a game to see if I can get the whole set 🙄

@SeeSi 2 жыл бұрын

Very informative. Cheers 👍🏻

@IngridsVanlife 2 жыл бұрын

thanks for the great advice, hope I can have my diesel heater back up and running soon!

@johnhansen337 Жыл бұрын

Textbook video for folk who live with the machines and who fix them. Oration was perfect.

@vanlifesurvivorsguide Жыл бұрын

Thanks mate :)

@johnhansen337 Жыл бұрын

@@vanlifesurvivorsguide I will be polite and say that the Chinese engineers have a sense of humour as they make sure we spend lots of time fixing their kit without manuals, and using a jungle telegraph system of teaching. I have just given up on a unit which failed on a fan error. It completely filled the boat with thick smoke which took weeks to clear of odours. After buying a replacement board and sensor, mating the controller to it by altering the voltage to 12v, swapping the sensor and fan plugs round, and moving the fan earth lead to the outer pin, the little bugger booted up and warmed up nicely. It soon began to speed up the fan then an almighty crunching sound occurred and the fan error code came up and the unit went dead in a cloud of smoke. It now starts at full fan speed and fails in 3 seconds. Time to give up and place the unit and its parts in the "suspect spares" bin. 😕

@BorderlessBelik Жыл бұрын

super helpful - thank you for this simple breakdown

@colinarner790 2 ай бұрын

Well, here I am standing at the heater at 3 am and keep getting error messages. 30 seconds into the vid I realized I was simply blocking part of the heat line. Thank you sir, owe you a pint

@vanlifesurvivorsguide 2 ай бұрын

No problem mate, glad you found it helpful

@xingchao9125 2 жыл бұрын

Now thats how you make a youtube video. You're a bloody legend mate.

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate

@PrisonersNoLongerAccepted 2 жыл бұрын

Excellent info. Thank you 👍

@paulj5129 Жыл бұрын

A very useful video and thank you for supplying it.

@twosurfersinavan 2 жыл бұрын

Cheers for the advice and saved for future reference

@wanabewest Жыл бұрын

good job, thankyou for your clear and to the point explanation

@hcalory8706 Жыл бұрын

Very professional and comprehensive knowledge video of the heater! It's so cool! I can't wait to share it with as many people as possible!

@Sprucegrove123 4 ай бұрын

quick fix battery power was low, Thanks for the video I appreciate it

@marien1991 5 ай бұрын

I had error code E07 and I managed to fix the problem, thanx to this video.

@teddekker3383 Жыл бұрын

Thank you !! Ted & Rosie 🌹

@jonny1943 Жыл бұрын

Very good clip! Thanks! 🙌

@leorutherford5456 2 жыл бұрын

Great video, very to the point, I had e-10, seems to run fine after the second start attempt

@mrjockey87 9 ай бұрын

Did you just start it again without the primingsequence? Ours starts and shuts off

@keithm6117 Жыл бұрын

10/10 for you're effort "really good", my Hcalory is showing an E07 fault "New out the box" so I'm waiting for Hcalory to respond after emailing them. I've tested all the wires and there's continuity which is odd... Thanks again...

@stewartdavies6315 2 жыл бұрын

Absolutely brilliant Video thanks

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate

@peterjames928 Жыл бұрын

Excellent video, Many Thanks Only thing I can add is another problem with the soft walled fuel line. (I suppose its academic really as you wisely advised us to chuck the soft walled pipe so we wouldn't be using it anyway.) It absorbs the pressure from the pump so the fuel leaves the jet is a dribble so it won't burn. Instead of a series of spurts which is neccessary to vapourise the fuel so it burns.

@troydalby5500 2 жыл бұрын

Thank you kindly, I was going to rush out and buy the glow plug (ER03) but shall check my battery condition first. Long period of clouds etc , batteries could be low.

@tochriss 10 ай бұрын

Excellent information well presented.

@michelthibodeau8550 2 ай бұрын

Useful video, thanks 🙏

@markjohn5214 2 жыл бұрын

Thanks very helpful

@philmurphy5584 Жыл бұрын

Very helpful. Thanks

@markytat 2 жыл бұрын

Great video, thanks :)

@normanrussell5526 Жыл бұрын

My heater was not supplied with the installation guide, so this is just the ticket, thanks.

@wolfygaming4509 2 жыл бұрын

Hello,I had E-6 /the fan had slid down the shaft away from the nock sensor,I put a small socket on the shaft & 2blows with a pin hammer & that fixed that,then E-10 showed,this was a kink in the fuel line when I reinstalled it,your video was very helpful//:) I forgot to mention,this was coursed by me pulling out the power fuse,like a kill switch before the heater had finished its shutdown cycle !

@Diyman43 8 ай бұрын

Does it not slide back again through time on using as it’s not locked in?

@ansisivans5201 2 жыл бұрын

Good. Thank you!

@smidsy2 2 жыл бұрын

Great video! Very useful

@vanlifesurvivorsguide 2 жыл бұрын

thanks smidsy

@Dirt-Diggler Жыл бұрын

So bloody nice to see a video on diesel heaters from someone who obv knows the subject 👍 there are way too many instant experts on YT 😤 Thank you for doing the research before making the video 😎

@phillipbriggs7682 Жыл бұрын

Great video, lots of good info

@interestedinstuff1499 2 ай бұрын

Excellent. Thanks.

@dumitrutocila5807 Жыл бұрын

Mulțumesc frumos 👏👏👍

@alberthuynh Жыл бұрын

Thank you for this!!!

@michaelbritton2331 2 жыл бұрын

thanks for the information and the time for making the video...

@terjehovde6818 3 ай бұрын

Exellent infos, thanks ! You are the best, werry good explainations, grettings from Norway

@directorstu 3 ай бұрын

Brilliant video. Subbed.

@vanlifesurvivorsguide 3 ай бұрын

Thanks mate :)

@bradleytownsend2294 Жыл бұрын

Brilliant thank you!

@natasharigler3414 2 жыл бұрын

Hoping to install a diesel heater in our T5 one day so we can wild camp all year round. Great video 👍

@douglundy5755 Жыл бұрын

thanks for not introducing your pets and travel interests but actually doing the job here! So refreshing!

@LukesVanLife 2 жыл бұрын

Like the vid buddy! Nice one. I'll be referring people to this vid 👍👍

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate :)

@kevinrobertfrasier1309 Жыл бұрын

Facinating. I today had fuel and tons of smoke billowing out from the air intake filter location. E10 error code.

@beccafairclough4617 2 жыл бұрын

Nice one 👍🏻

@pstoneking3418 6 ай бұрын

I've recently purchased a Chinese diesel hearer. I've found one thing that can cause an E10 error is using too small Guage wire. I connected it to my 12 volt batter that was approximately 30 feet away using 18 awg wire. Everything appeared to be normal until I realized that the fuel pump wouldn't run with the voltage drop caused by too small of wire. After I ran 12 awg wire Everything was fine until my battery got too low and caused a E8 error. For best results, If possible connect the battery using the supplied short cable else use 12 awg wire and keep the distance as short as possible. Don't use a power supply or ac to dc converter. You can use a battery with a trickle charger without any errors.

@marklloyd2966 7 ай бұрын

that fixed it thank you very much

@valivali7762 2 жыл бұрын

Thanks

@rvrandy1710 2 жыл бұрын

THANKS 🤠👍

@MrTyler2121 2 жыл бұрын

Great videos and very informative! Can’t wait to see more content on the diesel heaters from you. Can you include any information about manual adjustments to compensate for altitude? I wish I found your video sooner. I would have ordered the new blue controller that adjusts for altitude. You have the best information I can find on these diesel heaters.

@vanlifesurvivorsguide 2 жыл бұрын

Hi mate, we have one on order so we can make some videos on them so watch this space...

@fruyterfghhvvb6281 2 жыл бұрын

@@vanlifesurvivorsguide Great. Looking forward to seeing it

@PAK2133 Жыл бұрын

Thank you, unfortunately I was setting it as a normal timer and could not figure out the odd time it was starting and could not get it to turn off within the times I was setting it for, and I am well use to timers as I am a heating engineer.

@PLEASUREDISE 6 ай бұрын

Thanks so much 🙏

@jacobernst3753 5 ай бұрын

Regarding to much heat at lowest level- I have mounted a fuelpump from a 2kW on my 5kW heater, and it works fine, gets more economical too 👍

@dentop15 2 жыл бұрын

Boss video thanks for the information

@JG-xz6du 2 жыл бұрын

Great video!

@vanlifesurvivorsguide 2 жыл бұрын

Thanks mate :)

@atomshoemaker5297 Жыл бұрын

Well said. Ty

@williamwilson1816 2 жыл бұрын

very helpful fixed problem , error code 9

@danyf3116 2 жыл бұрын

The address of this video should be added in the reference part of the badly translated manual. I'm keeping this link for future reference. Kudos man. ☺

@jaredcolahan759 Жыл бұрын

TY, NICE VIDEO

@SuperyachtBroker Жыл бұрын

Thank you

@Ralphs-House 7 ай бұрын

E-01 error code on a Chinese diesel heater will also come up if the octane rating of the fuel is too low (ie if you have veg oil in the mix) and it will refuse to fire up from cold as a result, shutting down and throwing the code along with a fuel icon. Its important if you do run mixed fuel, that you always run straight diesel or kerosene at full pelt shortly before shutting it down (and when starting) to purge the fuel line of any oil and to clean the glow plug. These heaters are less fussy when hot and will happily burn a mixture. When cold its a different story. If you do end up with a mixed tank and unable to start it, you have to syphon the tank contents as much as you can, replenish with a measure of neat diesel or kerosene, attempt to start it a few times and once it does, get it up to temperature quickly and then put back what you drained out. Restarting will create a cloud of smoke until all the oil is burnt off through heater and exhaust but should soon settle down. A solution is to have a switch-over tap so you can switch between mixed and straight fuel sources to avoid this. E-01 error is nearly always low power from battery or transformer - EXCEPT when it also displays the fuel icon. In this case its telling you its unable to ignite the rough fuel rather than having power issues, but will still throw an E-01 code. Hope it helps someone!

@PunctualMrSmith 5 ай бұрын

Hey I am getting e01 but it is from my boats diesel tank. It’s been working fine but it’s currently extra cold. I am getting a small voltage drop of about 0.4 v once started. On the remote it shows a fuel symbol so I am wondering is it because the system is too cold and the small voltage drop is not able to get it going? Thanks in advance

@christineyates1391 2 жыл бұрын

thank you

@keithmorgan3295 Жыл бұрын

Low heat output and e-08 shutdown after a few minutes was caused by a dirty glowplug screen and partial blockage of the small air-hole in my case.

@dillonmay1 2 жыл бұрын

Brilliant vid👍

@vanlifesurvivorsguide 2 жыл бұрын

Thanks Daren

@alanhill2886 2 жыл бұрын

Thanks sorted out its problem in minutes, inlet screen half blocked with dust , code e 05. Trying to work With manual provided is hopeless

@baldassarrephotography2904 2 жыл бұрын

I will need to repost these on sooo many fb posts where people are going mad over these error codes.. 👍🏻

@davehimlin2374 Жыл бұрын

Do you think it is a wise decision to do this on a new unit ? Take it out of box, and add a few drops of 2 cycle oil inside the fuel pump then reconnect the fuel hose and manually pour diesel in the fuel line then hook it all up and do the prime- start up procedure ? This should really help lubricate the fuel pump during its initial startup when it is new out of box ?

@craigyb1274 2 жыл бұрын

Awesome 👌

@vanlifesurvivorsguide 2 жыл бұрын

thanks mate

@Warren007 5 ай бұрын

Just another thing worth mentioning for E01 that I've just fixed - I accidentally plugged the heater into 240v(the plug was identical to the one that goes into the unit and the transformer) and I fried the unit. After replacing the circuit board I was now getting E01 error despite there being enough voltage & amps for the unit. In my case, I had to replace the display/control which removed the E01 error. Goes without saying, don't plug 240v into a 12v unit!

@mikeakerstrom1667 Жыл бұрын

Missed a very important cause for E-08. This can be caused by the heater being too dirty to light, meaning that the heater needs to be taken apart and cleaned (or just replaced)

@eddiefarrell2425 2 жыл бұрын

top advise

@tomdawe5039 Жыл бұрын

I had an e05 error code keep coming up and the heater unit itself was very hot to the touch so I went into the factory settings and uped the minimum fan speed to 2500 rpm from 1500 rpm and it solved the issue as it draws the heat away from the heater quicker

@malachieven446 9 күн бұрын

Thanks!

@vanlifesurvivorsguide 8 күн бұрын

Thanks mate thats our first ever super thanks

@livelongandprosper70 2 жыл бұрын

Error code E-01 *tip* ..if I try to start the heater above 15 degrees c I get the error E-01 BUT 15 degrees or below, it starts fine..once heater is running I can turn the heat up no problem..

@dejanbelec8611 Жыл бұрын

Useful

@SANTO971 2 жыл бұрын

Problem I had. After about a year of use the rubber mount for the fuel pump broke apart. The pump was held only by wires and fuel lines. Symptoms: works and then sporadic error 8

@ajpepe72 7 ай бұрын

I’m getting e-10, good voltage at the heater, have just stripped the heater and all looks fine, no flooding and just a light dusting of carbon inside the chamber. I’ve ordered a service kit anyway, see what happens when I put it back together.

@husksboat 2 жыл бұрын

Very informative! Great idea about leaving a quarter tank of fuel when connecting into the main fuel tank! Have you got a link for the nylon pipes?

@vanlifesurvivorsguide 2 жыл бұрын

thanks mate, yeah the link is in the description but here you go ebay.us/8gA1HU

@niclazzareschi Жыл бұрын

Link is expired. Got a new one?

@jameskim62 2 ай бұрын

VERY GOOD INFORMATION AND EXPLANATION!!!!!!!!!!!!~~~~~~~~~~ 12 SUBSCRIPTION ON YOUR WAY.....

@GypsyTinker2012 Жыл бұрын

Excellent video. Might want to add the circle with a line through it. I believe it is bad connection to fuel pump. Trying to figure it out right now.

@vanlifesurvivorsguide Жыл бұрын

that just means that your heater isn't running its not an error or anything, once you start it up it will go. Have you primed the pump?

@GypsyTinker2012 Жыл бұрын

@@vanlifesurvivorsguide Thank you for the reply, it just started running! Thank you for this great and thorough video.

@SuperXs1100 2 жыл бұрын

Decided to by one, and keeps throwing p-01 code on 12v, 24v, new batteries, with charger on them and is reaching required power levels per the manual. Even added some juice to see if it would throw a high voltage code but never did. What controller and board would you suggest to get for this just so I have a piece of mind?

@vanlifesurvivorsguide 2 жыл бұрын

Hi mate, there isa motherboard and controller and remote set in this post we recommend. you will need the 5kw motherboard and then we suggest the blue controller with the red remote as the best option for controllers www.vanlifeuksurvivorsguide.co.uk/post/chinese-diesel-heater-spare-parts-added-extras-upgrades-2-0

@a1d3nh0 5 ай бұрын

I have a triclicks (Amazon) heater installed in my van. I’ve only used it 2 times, once when I installed it (for 15 mins) and once yesterday for 10 minutes. The engine temperature says 200 degrees C. No errors but that doesn’t sound right? Also, even after 10 mins it runs the CLEA function when I power it off. I read that it only does that after long use. Is there something wrong with mine?

@DGCSPEEDSPRAY 2 жыл бұрын

Great video very helpful. I suspect I have flooded the burn chamber and getting e10 as when I prime the diesel alway runs to the bottom of the hose leaving air trapped at the top. How do you solve a flooded burn chamber?

@McKaylaRuesch 2 жыл бұрын

I’m having the same issue, would love to hear if you were able to solve it and how?

@kennethbundy7513 6 ай бұрын

I just watched your error code video. I wish I had seen this much earlier. Very well done, I have immediately subscribed. I do have a voltage question. My controller reads much lower voltage than a direct metered voltage check of the battery. Any suggestions?

@vanlifesurvivorsguide 6 ай бұрын

Hi mate, that sounds like volt drop. So the cable between the battery and the heater isn't thick enough and should be thicker. we recommend 6mm2 (10awg). We also recommend going directly to the battery via the inline fused attached to the wiring loom and not through any other fuse box as this can cause volt drop too :) Thanks for the sub

@bennym2893 Жыл бұрын

Thanks mate, great no nonsense video. I have just purchased one of these from Vevor. Got it all set up in my shed last night, running off a next to new motorcycle battery (temporary whilst I wait on my inverter) I'm getting an e 2 fault with this though which seems strange, and you say it's most unusual. Anyone able to chime in what this could be?

@heloisecockenpot Жыл бұрын

got today after installation a e-2 with a vevor like you. anything to help me?

@bennym2893 Жыл бұрын

@@heloisecockenpot hello mate, once I put the power inverter in and ran it off of mains electricity It worked perfect after that. Seems the battery I was using wasn't up to the task, which I did find a little strange