MY CONCLUSION IS THAT THE RADIO OVERHEATS LIKE CRAZY AND GLITCHES

7 minutes of I don’t even know, 7 minutes should have taken 2 minutes

I'm going through same issues, thunpin auto telling me it's the radio itself need replaced(factory)... it works then stops like it's lot power,etc.. like it don't make any sense. Seems like a glitch

So what was the work around for the wire causing issues? White & red.

Just in case no one has figured it out yet the white and orange wire he is talking about is a can bus + and the white and grey beside it is can bus - they are info wires and voltage fluctuates based on info received or sent

That's NOT a fix. You're addressing the symptom, NOT the problem.

Very interesting stuff!! Someone will benefit from this vid 👌🏼

Open rear hatch, remove 3rd row seats, remove plastic trim below drivers side rear side window, most likely you will find your short in the bundle of wire below your rear hatch actuator which rubs against the wires and begins with shorting out the camera wire which sends the short to the radio first noticeable when going into reverse and camera glitches eventually causing radio to stay off. What you are doing is bypassing the short from camera.

how is the wiring diagram to connect Mygig RHB

nor my radio does work, nor does the whole screen or backup camera work. is it the whole radio unit or something else. I use scanner i got message instrument cluster error but No DTC CODE

How do you bypass the red and white wire in this case? Thanks.

A bit confused. How do you bypass the red and white? So just exactly what needs to be done, bought, etc to make this work?

hi, over the course of the day the screen went in and out. finally went black.when i back up the screen stays black but the backup warning still beeps .any ideas?

changed out my radio and just found the speakers and power wires. radio plays ok now. dont need anything extra because i didnt buy any adapter cables i just taped off everything and used screw on wire connectors, real cheap.

That assy (blue/white) wire is to turn on an amp. When you turn your radio on it powers that blue wire to turn on an amp or power antenna. The yellow is constant power 12volt + The red is a accessory or key on 12volt+. I've seen another post that claims the radio fuse needs to be pulled and the power wires to the battery have to be disconnected for a couple of hours. Then you hook the battery back up and lastly instal the radio fuse and it makes the radio and display work again. Don't know why but someone else tried the trick and it worked for them. I'm about to try it on my landlords 2008 Town and Country because her radio and touchscreen is not working either. Let you know if it works for me.

My 2010 AM/FM doesnt have sound but my aux & satellite has sound. Makes no sense

The fix is @5:00

How do you get the radio off the dash to begin with??

Ours is doing this. Radio works. Kids can watch movie on back screen and use remote to control but it is just all fuzzy on screen. Started just like your wife. I’m not mechanical so I have no idea how to do what your saying and my husband says just buy a new one but sure wish I could fix it and save the moneu

My radio works but I can’t play downloaded music. It flashes from pause to play over and over. That’s the only thing that I want, I don’t want to listen to the radio.

Any keyed on 12v power source can replace the red/white wire the red and white wire if im not mistaken is the "remote" wire for the amp follow it back to the amp and do some testing on it me personally I think the amp is a bigger problem to these radios than the radio itself but I mean I've replaced bunch of radios for sure lol and its typically the radio but I feel like the amp is shorting internally and feed back to the radio

I don't get what you mean when you said bypass the wire I don't see it bypassed in the video

Mine just doesn’t come on, or it just turns the whole thing white. It connects my Bluetooth but nothing sounds and seems on. Any help?

Can someone help me with my Chrysler town and county radio it skips when my aux is connected

What year?

Those wires are the canbus

just what the hell are you talking about.....?????

You take to long to explain

It's a dodge, everything shorts, especially the windows. Anything that moves, like a door hinge...they put wires near. 4 door truck, your wires are just smashed. Easy fix, buy toyota..lol..extend wired and relocate them.

Do you even know what your talking about because I don't.

OMG way too much small talk get directly to the point of the video

Do not listen to this guy. Do not do ANYTHING he's recommending.

Wasted my time here.

That assy (blue/white) wire is to turn on an amp. When you turn your radio on it powers that blue wire to turn on an amp or power antenna. The yellow is constant power 12volt + The red is a accessory or key on 12volt+. I've seen another post that claims the radio fuse needs to be pulled and the power wires to the battery have to be disconnected for a couple of hours. Then you hook the battery back up and lastly instal the radio fuse and it makes the radio and display work again. Don't know why but someone else tried the trick and it worked for them. I'm about to try it on my landlords 2008 Town and Country because her radio and touchscreen is not working either. Let you know if it works for me.