New ! Important Battery Message Removed With Soldering Iron

Рет қаралды 57,591

3 жыл бұрын

New ! Important Battery Message Removed With Soldering Iron.
You do NOT need the welding machine now to fix this.
We once demonstrated how to remove iPhone 11 Important Battery Message two months ago. It took about half an hour and a spot welding machine was needed. In this video, we share an improved way, which takes only 3 minutes, much more efficient.
Please check the video for more information.
Tools used in this video
Screwdriver set
Hot air gun desoldering station
Anti-static rubber mat
PCB cleaner
PCB holder
Tweezers
Solder flux
Insulation paste
Multimeter
Lightening cable
ALL Total Solution of Non-Genuine Message In this list

Пікірлер: 134

@Zemine77 3 жыл бұрын

A really great idea and perfect solution , thank you for sharing precious info.

@CINOTechnology 3 жыл бұрын

Thank you

@jayrue239 3 жыл бұрын

Thanks for showing that you can use solder to replace battery board. You're awesome😁

@CINOTechnology 3 жыл бұрын

: )

@DirkOppitz 2 жыл бұрын

I have seen in other videos that the battery must be activated extra after the board swap, otherwise it is not recognized by the phone. Rechit it really to install the battery and then connect the charging cable?

@arash9211 3 жыл бұрын

Congratulations on your useful trick.👍👍👍

@CINOTechnology 3 жыл бұрын

Thank you

@sherrehman8457 3 жыл бұрын

Good work sir always

@CINOTechnology 3 жыл бұрын

Thank you for watching

@rigoleyja4043 3 жыл бұрын

So i just to solder the connector. I dont have to micro spot it?

@tonya9614 3 жыл бұрын

Thank you 🙏🏻

@CINOTechnology 3 жыл бұрын

：）

@ninjadoesntexist5129 3 жыл бұрын

Thanks you so much

@CINOTechnology 3 жыл бұрын

: )

@dannydavito201 2 жыл бұрын

My qianli icopy read battery with the additional adaptor but after a few seconds drops signal then reads again then drops signal then says reading failed even though it brings up all the battery information, any ideas?

@cikhijau617 9 ай бұрын

What volt shoud i use for solder bos?

@sharmaxop Жыл бұрын

is it safe to remove those strips with soldering iron?

@kuroyukihime3026 3 жыл бұрын

Xan you revideo this in kuvh close r to see how you soldering it

@madushanweragama6702 3 жыл бұрын

Cino thanks bro...

@CINOTechnology 3 жыл бұрын

: )

@adelejean987 3 жыл бұрын

is it safe to use soldering iron on battery cell output? will not to effect Battery ? bcoz 360C is passing through the battery pin. (what about using battery welding machin insted?)

@CINOTechnology 3 жыл бұрын

It needs to be very careful for phone repair

@user-pi9fz6rm7v 3 жыл бұрын

What if there is a short circuit or sparks during repair? And tell me what to do when that happens. CINO Thank you all the time.

@CINOTechnology 3 жыл бұрын

Replace the short-circuit parts

@SathisComputerServices 2 жыл бұрын

HI, your video are such useful for me as technician. If you don't mind can share the specific model/brand of the solder flux? I have it but not sure what's the function of it..

@kirbygriffin836 2 жыл бұрын

it helps the solder stick to the metal

@triniapache 2 жыл бұрын

Hey love the video ,Question what is the temperature that u used when desolderin ? Many thanks bro

@LeeMooEez 2 жыл бұрын

Open your eyes bigger and rewatch the video 😂

@triniapache 2 жыл бұрын

@@LeeMooEez 😆 🤣 I saw dat when I rewatched it that's wat I get skipping through it thanks 😊

@user-rn7ry9uo9l Жыл бұрын

I use to spot weld the bms to new cell. Is it better to spot weld or solder ?

@jasonvoorhees3282 Жыл бұрын

Spot welding will leave permanent mark on the BMS pad, whereas soldering does not. Solder is the way to go.

@retrotech11 2 жыл бұрын

Great video! I tried this method but still got the battery warning message pop up! Please advise, do I need to do a factory reset on the iphone to remove the battery warning message?

@randomscience4k 2 жыл бұрын

Apparently I saw on another video and they used a little bit different method and said that both the old and new is required else the message will come back. kzfaq.info/get/bejne/p52Peq-Vr5yzo6M.html&lc=UgyD_VIb5AKH0W86ErV4AaABAg.9UdjDip95Nh9Uds_oMwW6Q

@sharmaxop 4 ай бұрын

try to force reboot ur phone by long pressing volume up button and power button until apple logo appears. After appearing apple logo u can relase the buttons nd wait until phone boot to lock screen and wait if the msg automatically disappers

@retrotech11 4 ай бұрын

@@sharmaxop it's just Apple being Apple, no getting around it without the right tools. Thanks for your help anyway.

@ecuchipgarage5894 3 жыл бұрын

It’s okay to transfer original flex to an aftermarket battery ? Thanks.

@CINOTechnology 3 жыл бұрын

Can you plz describe your problem more specifically?

@ecuchipgarage5894 3 жыл бұрын

@@CINOTechnology If I can transfer the battery board from the original battery and install on an aftermarket battery.

@siddharthbhavsar3990 2 жыл бұрын

I tried the same thing...it is not turning on... I think the flex is damaged...but I cannot see where it is damaged

@kervymadera3841 Жыл бұрын

and how about battery healt,

@Eric-vn9sm 3 жыл бұрын

What battery from amazon u recommend for iPhones ?

@CINOTechnology 3 жыл бұрын

www.cinomall.com/collections/batteries

@njmusic837 2 жыл бұрын

I wouldn’t get one off of amazon

@mohdshariq2018 2 жыл бұрын

But what about battery health percentage how we make it hundred percent?

@rahabarmustakim 2 жыл бұрын

What if you don't have the original battery.

@KimoKimochii 3 жыл бұрын

Is the PBC holder used to prevent over heating? or I can use anything to hold the battery in place?

@CINOTechnology 3 жыл бұрын

Better use the specialized PCB holder

@KimoKimochii 3 жыл бұрын

@@CINOTechnology what is the purpose of the holder? can i use something else like a piece of wood?

@user-pi9fz6rm7v 3 жыл бұрын

Can I use paste instead of flux?

@CINOTechnology 3 жыл бұрын

No, they are different items

@krantikoganti 2 жыл бұрын

When you weld old cable (bms) on the new battery what is the temperature you used to the Soldering iron. Is it 360 degrees centigrade?

@CINOTechnology 2 жыл бұрын

330℃

@tattoosteveneo Жыл бұрын

Question? Will this also fix the battery health and put it back at 100% or at least close to it??

@CINOTechnology Жыл бұрын

Won't. The information on the previous battery is displayed. But this does not affect usage. This battery information is no longer accurate

@tattoosteveneo Жыл бұрын

@@CINOTechnology thanks for the reply. Could you solder the stainless ends together instead of desoldering the board?

@redhotsumo 3 жыл бұрын

Will this method work on an iPhone XS?

@CINOTechnology 3 жыл бұрын

yes

@ElvisTafaPhotography 3 жыл бұрын

So lost/damage original battery flex cable will never solve the problem?

@CINOTechnology 3 жыл бұрын

Yes, at least right now there is no other way

@adelejean987 3 жыл бұрын

thats why i left f**+king apple, and shift to Huawei. cheap and best phone. my money, my phone, my whish.

@sharmaxop 4 ай бұрын

if u lost ur original battry or battry flex only iphone X or lower device doesnot need original flex u can buy aftermarket battry and battry health shows without any og bms board but after iphone X apple has introduced a speacial bms board with encrypted coding so we need replace only the battry cell in old battry to show health.

@spark_y4893 Жыл бұрын

Does it remove the battery service message too?

@CINOTechnology Жыл бұрын

The information of the last battery is restored, but this information is only a form, the purpose is to eliminate the warning pop-up window

@phuhardlawal5189 Жыл бұрын

What if the original battery that comes with the phone can no longer be found? Can 1 use another original battery from other iPhone?

@sharmaxop 4 ай бұрын

no not possible bcoz every iphone's bms board is binded with cpu with a encrypted coding which iphone always verify when we reboot the phone and if ur original battry bms is misplaced u are no longer show the iphone battry health.❤

@sajidaktar1056 3 жыл бұрын

Will it be still showing older battery health ??

@muzafferkarabulut9013 3 жыл бұрын

You have to Programm it to 100% with qianli icopy or something else

@khajask8113 3 жыл бұрын

Can use icopy or i2c programmer...?

@CINOTechnology 3 жыл бұрын

Sure

@khajask8113 3 жыл бұрын

@@CINOTechnology which one is best..?

@martinheini7426 2 жыл бұрын

@@khajask8113 Apollo one from qianli (my personal preference) it's simple and effective.

@sharmaxop 4 ай бұрын

@@khajask8113jcid v1se wifi best in all type of programming works

@Said_DJZ 9 ай бұрын

it works for iphone 13 ?

@directsystems2225 3 жыл бұрын

What soldering iron are you using.. Share that please

@CINOTechnology 3 жыл бұрын

We use this one: www.cinomall.com/collections/tools/products/atten-ms-300-3-in-1-combination-hot-air-gun-desoldering-station-dc-power-supply-maintenance-system

@nilomyki 3 жыл бұрын

@@CINOTechnology What Multimeter Probe Tips are you using?

@SH-ef3xp 4 ай бұрын

My iPhone 11 Pro recently had charging issues and technician removed the battery. While reassembling he did not put any Adhesive back of battery. Now I feel my battery is heating a lot. Does it because of no Adhesive back of Battery? Do Adhesive act as thermal paste like the one we use in case of computer processor??? Please let me know and also if you can share a buying link…. Anyone else facing similar issue??? Please reply in detail

@KrushnaChDas-mg6yw Ай бұрын

It’s maybe power ic issue.

@LofiBoy0 10 ай бұрын

I changed the battery and the bms the message disappeared but the battery health didn’t change

@phonotologist Жыл бұрын

I did replace it with the genuine battery but it drains battery really fast dont know why???

@hosmoon 3 жыл бұрын

How is the battery health displayed when using this method?

@ghahayuadanim7091 3 жыл бұрын

@CINOTechnology 3 жыл бұрын

The old data. But we can surely clear the data with the battery tester /LOL

@MrSyaaz-my8fn 3 жыл бұрын

@@CINOTechnology what do you mean boss? is battery health can appear 100 again after replacement?

@merlijn5046 3 жыл бұрын

@@MrSyaaz-my8fn It will notshow an updated battery health, but you can reprogram the chip on the battery flex to make it show an updated battery health percentage.

@ThePawciohd 3 жыл бұрын

Soldering very easily damages the bms board. I damaged 4 tiles in this way.

@CINOTechnology 3 жыл бұрын

It requires patience and carefulness.

@Bartekk955 3 жыл бұрын

You can cut battery cell from original battery, and soldering with low temp paste to avoid damage

@Ari-hh4bw 3 жыл бұрын

After solder will the battery have problem like circuit on fire or something?

@CINOTechnology 3 жыл бұрын

no. but if you do not careful with that it might happen

@Ari-hh4bw 3 жыл бұрын

@@CINOTechnology thanks and how about iphone se 2020? Does it appear important battery message too?

@CINOTechnology 3 жыл бұрын

that depends, original display,aftermarket display...

@Ari-hh4bw 3 жыл бұрын

@@CINOTechnology ow so as long as its genuine the message will not appear right

@muzafferkarabulut9013 3 жыл бұрын

@@Ari-hh4bw It makes no difference if it is a genuine battery it will appear same by the display

@gamerzak2x Жыл бұрын

Does it go back to 100% battery health though?

@CINOTechnology Жыл бұрын

nope but does not affect the use of just the form

@dzaraing4495 Жыл бұрын

when i want to activate the battery, iphone restarts without stopping. Why ?

@kingtham 3 жыл бұрын

Problems is the battery show old percent with the new one.

@niglo7779 3 жыл бұрын

Icopy can make a 100% battery health.

@cegledicsabi Жыл бұрын

Guys, I don't understand this. I use flux and 360 degree solder, but it doesn't move. The flex won't let go that piece of metal. What's the trick? That's all I need to be able to do this

@nikitazaycev8636 Жыл бұрын

soldering directly on the bms is not recommended though, the chips get easily overheated and the bms stops working

@LofiBoy0 10 ай бұрын

True

@user-pi9fz6rm7v 3 жыл бұрын

Doesn't the flux need to be removed?

@CINOTechnology 3 жыл бұрын

Yes, remove all the remaining flux

@esyh8606 3 жыл бұрын

The old battery is damaged. Was lost. How do I transfer data

@CINOTechnology 3 жыл бұрын

That depends on what phone you use

@RizwanKhan-mz9xy 3 жыл бұрын

My iphone xr is not turning on its completely dead what should i do

@CINOTechnology 3 жыл бұрын

Power it on with DC power and see its current

@ulrichkessler9328 3 жыл бұрын

Can i apply this method (solder) to iPhone XS MAX?

@CINOTechnology 3 жыл бұрын

Yes. Apply the method to any iPhone battery.

@hafiziskandar8759 2 жыл бұрын

If i dont have a original flex cable , any chance that i can get my battery health back ?

@CINOTechnology 2 жыл бұрын

yes

@hafiziskandar8759 2 жыл бұрын

How ?

@sanjeevmobilecare4022 3 жыл бұрын

Batrry flex solding scene is invisible

@CINOTechnology 3 жыл бұрын

How so? Check 3:42

@geek8673 3 жыл бұрын

How much battery health is it showing now?

@CINOTechnology 3 жыл бұрын

The battery health has no change

@user-yb7fs9rc9o 3 жыл бұрын

换完了电池无数据什么情况

@CINOTechnology 3 жыл бұрын

换电池后刷机了

@aneytxo 3 жыл бұрын

Mentira. No se puede quedar sin corriente la tableta. Mueren los chip s

@CINOTechnology 3 жыл бұрын

Si vous ne comprenez pas, ne dites pas de bêtises. Nous sommes très professionnels. Ceci est notre zone de commentaires, ne nous forcez pas à vous gronder. Votre mère ne vous a-t-elle pas appris à parler poliment ?