Citroen C1 Rear Brake Shoe Replacement | FULL Easy DIY Guide

  Рет қаралды 66,222

Cyclone Cyd

Cyclone Cyd

Күн бұрын

Full guide for YOUR Citroen C1 rear brake shoe replacement. 107 and Aygo are the same. Ours were only half worn, but the handbrake levers were seized.
🎥 C1 / 107 / Aygo front discs & pads: • Citroen C1 Front Brake...
☕ Support the channel here: www.buymeacoffee.com/CycloneCyd ☕
💡 Subscribe and hit that bell 🔔 to learn more about looking after your car.
With such a lightweight car, the rear shoes would normally be expected to last a long time. These had done 85k miles and were a little less than half worn. On this basis, you might expect shoes to last 160-200,000 miles but as can be seen, issues other than simple friction material wear can cause replacement.
Unlike disc brakes, the dust in drum brakes is trapped inside the drum. There was a lot of dust and on this basis I would suggest that the drums are removed for a clean at least once a decade or every 75-100,000 miles.
🛠 Some gear you might be needing
Got a fluid leak❓ Here is a Febi Bilstein kit with shoes, cylinders and fitting kit:
UK: amzn.to/3BeOZ4J
Shoes only, Borg & Beck:
UK: amzn.to/3evmfuK
Don't forget brake fluid if you're changing cylinders or yours is more than 2 years old
UK: amzn.to/2Ujyzrk
BIG 600ml spray can of brake cleaner. This is what I use
UK: amzn.to/2UgGaqB
MINTEX Ceratec (same as I use)
UK: amzn.to/2Un5Ph6
Or maybe you like Liqui Moly products (I do, they are generally very good)
UK: amzn.to/3xRMjI6
Learn more about looking after your car:
🎥 How to replace a CV [constant velocity] joint boot with a split kit: • Universal CV Boot Repa...
🎥 Don’t let your fuel filter end up like this 100,000 mile old example:
• Why Should I Change My...
🎥 Battery & alternator care in this playlist: • Alternator and battery...
Everyone should have a tyre pressure gauge in their glovebox:
bit.ly/Tyre_press_guage
bit.ly/Pressure_Gauge_2
I personally prefer a stirrup pump to a foot pump (I use the same one for my bikes and cars)
bit.ly/Tyre_stirrup_pump
If you’d like to learn about the science and engineering of cars:
Bosch Automotive Handbook:
amzn.to/39va9xA
Are you trying to grow your own KZfaq channel? I use TubeBuddy, try it out for FREE:
www.Tubebuddy.com/CycloneCyd
Like my theme music? Need music for yourself? Contact my nephew, Anton, via Facebook
/ anton.griffiths
Gear I use in filming and production:
bit.ly/CC_Gear
My videos are edited with Filmora X - try it for free
bit.ly/Filmora_X_try4free
Thank you

Пікірлер: 74
@CycloneCyd
@CycloneCyd 3 жыл бұрын
🎥 C1 / 107 / Aygo front discs & pads: kzfaq.info/get/bejne/bJejeqagytK9oWw.html
@Roadkill7878
@Roadkill7878 2 жыл бұрын
Well done. You are the first person I’ve seen doing these cars who knows how to release the shoes from the backplate properly
@CycloneCyd
@CycloneCyd 2 жыл бұрын
Thank you, sir.
@royanl
@royanl 6 ай бұрын
The best explanation of how to replace your brakes. Thanks!
@StephanWahlen
@StephanWahlen 2 жыл бұрын
Thank you so much. I managed to replace the shoes of my Aygo. It's not that complicated, but your video helped my a lot. I have 200.000 km on mine (124k miles) and i hope its good for another few years now that i replaced the rear brakes, muffler, catalysator/manifold and suspension couplers.
@CycloneCyd
@CycloneCyd Жыл бұрын
Thanks Stephen, glad it helped.
@greaser7765
@greaser7765 2 жыл бұрын
Going to tackle this job on my wife’s Peugeot 107. This video is exactly what I need 👍🏼
@Domnaek
@Domnaek 2 жыл бұрын
Finally a comprehensive how to on the aygo! Thanks a lot :)
@francissomadaly4043
@francissomadaly4043 2 жыл бұрын
Excellently descriptive video as always thanks Cyd. I really struggled though with the adjuster spring that fastens to the leading shoe. It came off with this spring under the shoe as did yours but you replaced back on top of the shoe. It's only when I went back to check what I was doing wrong I noticed the difference. I'm supposing this doesn't matter because I really wanted it to go back as original but I'd probably need super powers to do that 🙄 or a special tool. Cheers 👍
@edenf7704
@edenf7704 Жыл бұрын
Cyd, thank you. I'll be using this as a guide for my Swift with brake shoes.
@hagenwenzel8609
@hagenwenzel8609 Жыл бұрын
Excellent video, helped me a lot doing the job on my car. Greetings from Germany
@snowreptile8867
@snowreptile8867 8 ай бұрын
Excellent tutorial, eloquently spoken. Thanks.
@phillyleighton86
@phillyleighton86 Жыл бұрын
bloody amazing attention to detail thank you for creating such a informative video
@howardgold7562
@howardgold7562 Жыл бұрын
Good content. All the useful info without any flannel! Thank you.
@BarryAbbott
@BarryAbbott Жыл бұрын
Thank you, one of the best informative helpull videos i have seen 👍
@Carlostype
@Carlostype 2 жыл бұрын
Great attention to detail here especially the adjuster set up, this is where the avid diyer betters the garage job! So easy to make mistakes. Both my cylinders had seized and fric material detached on the wife's yaris😯 👍
@CycloneCyd
@CycloneCyd 2 жыл бұрын
The wear rate on these small light cars is so low these brakes would last forever if it weren't for 'other' problems!!
@paulogomes6223
@paulogomes6223 Жыл бұрын
Its a good help i have a Aygo with some problems with rear breaks
@Chris-bv4yh
@Chris-bv4yh 5 ай бұрын
Excellent video. All those niggly details covered. Thanks
@tomthompson7400
@tomthompson7400 2 жыл бұрын
If you had included a check for seized slave cylinder pistons and a look behind the rubbers for leaks , it would have been a perfect video , great job on the close ups and explanation of the auto adjusters , best video Ive seen.
@CycloneCyd
@CycloneCyd 2 жыл бұрын
Never seen a seized rear cylinder. Plenty of leaking ones, but not seized. I guess it must happen though. Good point though to check it's okay.
@tomthompson7400
@tomthompson7400 2 жыл бұрын
@@CycloneCyd I had two on mine , needless to say not found till saturday afternoon , but got them freed up and not leaking , so all is grand for a while.
@enemycrab9229
@enemycrab9229 2 жыл бұрын
@@CycloneCyd Just been to a garage and had mine diagnosed as seized. Wheel wouldn't turn freely when up on lift, apparently. Was looking for a vid on how to replace the brake cylinder (aka slave cylinder), but not to worry!
@CycloneCyd
@CycloneCyd 2 жыл бұрын
@@enemycrab9229 once you've got the rear drums apart, replacing the cylinders is a doddle. Have a look at this video on my son's old Polo. I remove and replace the cylinder in it. The Polo one was held in with a screw, can't remember how the C1 is held in, but some use clips. kzfaq.info/get/bejne/brSilKWZy72loJc.html
@markslade9722
@markslade9722 9 ай бұрын
@@CycloneCyd I think until you have to change the rear wheel cylinders on this car yourself, I think you would take those words back. Yes looks very easy, and should be, but the cylinders are aluminium with steel brake pipes going to them, so what should be an easy job, turns out not to be, and an expensive one. Even with heat, flare spanners, releasing oil, then still the brake pipe nut to the cylinder rounds off, mole grips etc, you will end up having to cut the pipe and fitting a new brake pipe with the cylinder. Both my rear cylinders on my 07 plate C1 seized, and I found out all this then trying to change them. Seems common for the wheel cylinders seizing on these C1's.
@volt8684
@volt8684 2 жыл бұрын
You make it look so easy. I do most my own jobs and my daughters but drum brakes give me nightmares
@rockpodd
@rockpodd 2 жыл бұрын
Doing this tomorrow on my Peugeot Partner. Excellent video. Thx alot.
@CycloneCyd
@CycloneCyd 2 жыл бұрын
Did it go well?
@andreramos945
@andreramos945 3 жыл бұрын
Great work, very professional
@overspeed3042
@overspeed3042 Жыл бұрын
You my friend are a genius 👏 thank you so much for your videos you have really helped me out so much ❤️
@CycloneCyd
@CycloneCyd Жыл бұрын
You are so welcome
@chazwalker7156
@chazwalker7156 2 жыл бұрын
Excellent upload - cheers 👍
@aquademiwellnesssolutions1883
@aquademiwellnesssolutions1883 Жыл бұрын
WOW, very helpful video ! Thanks a lot !
@TheBaeklev
@TheBaeklev Жыл бұрын
quality content as always mate!
@Dudeiculas
@Dudeiculas 5 ай бұрын
What a great tutorial this is well done 👏
@onlyme972
@onlyme972 2 жыл бұрын
Really good video, however Toyota official dealer manual says use copperslip on the bearing surfaces
@CycloneCyd
@CycloneCyd Жыл бұрын
Thanks for the info
@danieldoherty8009
@danieldoherty8009 Жыл бұрын
Best video yet ,unlike them other ones ,with annoying music.
@CycloneCyd
@CycloneCyd Жыл бұрын
Yeah, I stopped adding music ages and ages ago. Doesn't suit this type of tutorial IMO
@MrMucsosz
@MrMucsosz 2 жыл бұрын
well explained! like our teacher did at school. even my wife understood :-P
@pal555
@pal555 2 жыл бұрын
Great video I'm doing mine thanks
@britgerus1956Glen
@britgerus1956Glen 2 жыл бұрын
Excellent video
@user-ts2hf7zr5h
@user-ts2hf7zr5h Жыл бұрын
Спасибо! Все четко рассказали. Отлично проделанная работа!
@mikerudolph1321
@mikerudolph1321 Жыл бұрын
Very useful, thanks
@MarkRuiz521
@MarkRuiz521 Жыл бұрын
I notice the spring at the end of the adjuster (with screw) was replaced the wrong way round?
@maxthecaddy8451
@maxthecaddy8451 3 жыл бұрын
Thumbs up from me cyd 👍
@CycloneCyd
@CycloneCyd 3 жыл бұрын
Awesome, thank you!
@KukLinSky
@KukLinSky 2 ай бұрын
Thanks
@bengim8332
@bengim8332 10 ай бұрын
My brakes seems not to adjust themselves. And the brake pedal grips far down after I changed the shoes?
@Enpassantful
@Enpassantful 10 ай бұрын
Same set up on the Toyota aygo I think.
@sametsamet-sr3nj
@sametsamet-sr3nj Жыл бұрын
How many miles can I drive before needing to replace drum brakes ? Thx
@fastbudgrower4205
@fastbudgrower4205 Жыл бұрын
Bang on video,,,I could become a Mechanic off your video's
@CycloneCyd
@CycloneCyd Жыл бұрын
That's the idea. Better than getting ripped off by useless garages
@99justleon99
@99justleon99 Жыл бұрын
After how many kilometers or miles is this change
@Gourmondise
@Gourmondise 2 жыл бұрын
How much pain is to get that cable back is something that I cannot explain...
@garrynutter860
@garrynutter860 3 жыл бұрын
Great video Cyd, Thanks. Did you jack the car up under the beam between the two wheels ?
@CycloneCyd
@CycloneCyd 3 жыл бұрын
Yes I did, in the middle.
@bk-py6jx
@bk-py6jx 2 жыл бұрын
good. thanks.
@CycloneCyd
@CycloneCyd Жыл бұрын
You're welcome BK.
@lennonpolo
@lennonpolo 2 жыл бұрын
Hi there, great vid! Do you think this is the same for a Peugeot 108?
@CycloneCyd
@CycloneCyd 2 жыл бұрын
I don't know for 100%, but i would imagine so. Almost certainly very similar. Few drum brake systems are much different.
@ferenczsinko6770
@ferenczsinko6770 2 жыл бұрын
thank you for this. unfortunately for me the damn handbrake cables are slightly sticking and causing the brakes to very slightly bind & the MOT centre wont pass it. I have ordered new cables but have not found any online videos about changing this vehicles handbrake cables. I tried plusgas and wd40 on all brake drum components and spraying it in each end of the brake cable but it still sticks very slightly and the MOT centre refuses to pass it.
@CycloneCyd
@CycloneCyd 2 жыл бұрын
What's the drag figures from the roller tester? 10-15kg would be normal per wheel and as long as it isn't above 25kg per wheel they really should pass it. As you can see from the MoT manual there is no specific requirement for the 'drag' to be tested or noted and there is no stipulated maximum. Do let us know how you get on www.gov.uk/guidance/mot-inspection-manual-for-private-passenger-and-light-commercial-vehicles/1-brakes#section-1-3-1
@ferenczsinko6770
@ferenczsinko6770 2 жыл бұрын
@@CycloneCyd Thanks for this. The MOT tester seems to have a braking phobia. I ordered new brake cables, shoes, drums and changed the lot now. Lets see what he has to say now.
@CycloneCyd
@CycloneCyd 2 жыл бұрын
@@ferenczsinko6770 even if it passes now, you could still complaint to DVSA . It sounds like he needs some learning
@mikhaillindan9091
@mikhaillindan9091 Жыл бұрын
I think you are outstanding
@xangadixxxx6405
@xangadixxxx6405 9 ай бұрын
Sir how long van the cylinder be in before changing? My Aygo has now 80.000 km down.
@CycloneCyd
@CycloneCyd 9 ай бұрын
If it ain't broke, don't fix it. They could last the life of the car, 250,000 miles or more. It was probably my fault for not bleeding the brakes often enough. For a while I wasn't able to after an accident. Back on it now though.
@xangadixxxx6405
@xangadixxxx6405 9 ай бұрын
Thankyou so much sir
@shpat7440
@shpat7440 2 жыл бұрын
Great vid!
@CycloneCyd
@CycloneCyd Жыл бұрын
Thanks Agim
@user-hl5kf7kq6r
@user-hl5kf7kq6r 3 жыл бұрын
marhaban mumkin musaeiduh ana min aleiraq sayaaratay nawe sab 9.3traz mudil 2004 mushkiluh alsayaaruh tusarun bishakl tabieiin wamin thama tatawaqaf ean aleamal wala tashtaghil muruh thaniah alih baed fasl alsaalib min albataarih warajaeih wataqum bitashghil wahakadha qumt bifahs kumbuyutar wala yujad 'ayu eutla? mumkin saeadni bialeiraq makw wahid yaerif allah yukhaliyk saeidni
@britgerus1956Glen
@britgerus1956Glen 2 жыл бұрын
Jacking bolts....
@tomthompson7400
@tomthompson7400 2 жыл бұрын
yep jacking bolts .
I Can't Believe We Did This...
00:38
Stokes Twins
Рет қаралды 123 МЛН
Дарю Самокат Скейтеру !
00:42
Vlad Samokatchik
Рет қаралды 8 МЛН
Changer les Freins arrière à Tambour Citroën C3 1 🚗
7:32
Ma Clé de 12
Рет қаралды 14 М.
How to Replace Toyota Drum Brakes Like a Pro
31:33
The Car Care Nut
Рет қаралды 648 М.
How To Change Citroen C1 Rear Brake Cylinder
4:56
Cyclone Cyd
Рет қаралды 8 М.
Most Common Brake Installation Mistakes!
13:29
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,3 МЛН
Rear Brake Caliper Piston Rewind - With and Without Special Tools
6:38
ScrewsNutsAndBolts
Рет қаралды 366 М.
Changer roulements arrière Peugeot 107
13:17
Paco le mécano
Рет қаралды 20 М.
The Only Brake Pad You Should Buy
10:07
Scotty Kilmer
Рет қаралды 809 М.
Inspect drum brakes like a boss!
19:27
Way of the Wrench
Рет қаралды 43 М.
STAGE12 200CC FL-R EN ACTION 🧡🧡
0:49
MAXISCOOT
Рет қаралды 16 МЛН
Раздали по 10 миллионов СОТРУДНИКАМ АВТОСАЛОНА. Что они купят?!
1:15:41
😳 ВЫЖИВАЮ В ДРИФТ МАШИНЕ
0:39
Настя, это где?
Рет қаралды 2,7 МЛН