Cleaning and adjusting a serger, Singer Ultralock 14U64A needs some cleaning and adjusting

Рет қаралды 20,971

4 жыл бұрын

This is a Singer 14U64A Serger that came to the shop. It has been well used and needs some cleaning and adjustment. Come learn with me as we open it up and get it back to serging like new. Time for the Sewing Machine Repair Guy to do some more repair work on a vintage sewing machine.
Support the channel, be a Patron: / sewingmachinerepairguy
Learn more about me on my website www.sewingmachinerepairguy.com
Also I'm on facebook / sewingmachinerepairguy
Check out my Etsy store! www.etsy.com/shop/SewingMachR...
Here are some of the products I use to repair sewing machines. These are affiliate links, they don't cost you any extra. They provide me a small commission if you purchase these products via this link. This helps me continue to provide videos for your enjoyment.
Tri-Flow Sewing Machine Oil (my personal favorite)
amzn.to/2XWMeSR
Tri-Flow Grease (my favorite grease)
amzn.to/2Y1e28r
Bottle brushes
amzn.to/3gVcohE
Nylon brushes
amzn.to/3gQGenh
Makita vacuum
amzn.to/2Xv2hrZ
Makita impact driver
amzn.to/36WJwAI
Wera screwdrivers
amzn.to/370qpFS
Starrett S423Z Steel scale set
amzn.to/2Xy4pzn
Krud kutter
amzn.to/2Bz7rLf
Denatured Alcohol
amzn.to/2z0kSTk
Towa tension tester
amzn.to/2U6Uq1O
Pliers, Parallel Flat Nose Smooth Jaw
amzn.to/3gPN4JN

Пікірлер: 75

@ambermyers6765 7 ай бұрын

I can’t wait to give mine a deep clean. The tip for the different colored threads is 👌👌👌

@chemagnepollard6231 6 ай бұрын

Thank you so much for posting this video I haven’t used my machine in almost 30 years and was afraid to do so since it has lain dormant. This video has taken away my fear of opening up my machine and oiling it all. There was a strange difference, my machine didn’t have the oiling pad on the inside. So, I oiled all that I could reach. After watching this I realized that the needle clamp was damaged and I found that I had the confidence to take it off and really investigate the damage.

@TennValleyGal Жыл бұрын

I've had this machine for many years and recently, the tension has gone all woky. Thank you for teaching me things I never knew about this looper. Gotta go - I'm off to do some cleaning, oiling (that's never been done!) then adjusting the tension. Happy sewing y'all!

@carolinecraig6253 6 ай бұрын

How'd it go?

@LLBryan 2 жыл бұрын

Am window shopping for a used serger. Just looked up this model and found your video. It is wonderful. I have learned a lot about the nature of sergers from you and about how users can help extend the life of their machines. Thanks!

@TheBretopia 3 жыл бұрын

Thanks for this. I have been pretty good about cleaning and oiling my machine since I got it 1986 but have never taken it this far. I'm glad I did. My wick and pad were dry. I remember reading the manual to oil it shortly after I first had it. All the oil points said 2-3 drops and the one above the wick said 20-30 drops. I decided it was a typo and should be 2-3 drops. So I've been giving it 2-3 drops only all these years. Poor thing. That said, I've run it hard over the years and have never had any issues. I should treat it to some new cutting blades. Thanks again.

@craiggrant28 4 жыл бұрын

thanks! My machine iz in need of a cleaning. Glad someone people make these vidzzz !!!

@jheesom 3 жыл бұрын

Hi Wes, Can I just say that I've used Isopropyl Alcohol to clean as well and it's good for cleaning grease and oil, but you have to be very careful on the outside of the machine as it can dissolve/smudge the printed lettering on the dials etc. I now use just weak watered down detergent to clean the outside of the machine for this reason.

@rjbrewer09 4 ай бұрын

thank you so so much. I just bought this machine second hand and I had no clue.❤

@memegwanseshkawkogan3412 3 жыл бұрын

I’m so glad I found this video. Had a 5 thread quantum lock given to me that’s been sitting for years. Cleaned and lubed it up but discovered the top bushing on the needle bar was too low. There wasn’t enough clearance and it wouldn’t do a complete rotation. That’s fixed and now the upper looper horn was bent... I’m determined to get it running smoothly.

@kathleenstorer691 3 жыл бұрын

I just received this exact serger-a friend of a friend bought if off eBay 5 years ago and never did anything with it. Mine is filthy, and I'm in the process of taking it all apart so your video is most helpful! Most of the removable plastic parts on mine are broken and or cracked-I see what you mean by tightening the screws too tightly. I'm hoping to be able to order some replacement parts but haven't gone down that rabbit hole yet. Thank you again for a very helpful video!

@sweettennesseelife1665 Жыл бұрын

Awesome video. Thank you for taking the time to create this content.

@mymai2792 3 жыл бұрын

This is very helpful - thank you so much.

@marjohnsmusings3222 8 ай бұрын

Thank you very much.

@baxter3877 3 жыл бұрын

Thank you, I found this very interesting!

@somedavechannel 7 ай бұрын

Thanks! Just picked up what maybe the same machine, this was very helpful!

@MariaPadron 2 жыл бұрын

Thank you for the video... I've found it on line and has the settings recommended for different fabrics....

@mika11isradier 4 жыл бұрын

Thank you so much for this video.

@SewingMachineRepairGuy 4 жыл бұрын

Thanks for the nice comment!

@EdnaDelacruz Жыл бұрын

Can you do a video on how to change the blades?

@menofairy 4 жыл бұрын

I just was given this machine this is amazing helpful...

@thecousiezzz4283 2 жыл бұрын

Same

@dbnkan 4 жыл бұрын

I was always taught to thread a serger loopers first, then needles. You threaded the needles first.

@SewingMachineRepairGuy 4 жыл бұрын

Yes, you are correct. Nice catch! It is possible to thread the needles first, just a little more tricky as the looper thread will have to go under the needle thread. Good rule of thumb, always thread loopers first. Do as I say, not as I do, lol.

@juliecasha7721 3 жыл бұрын

What was your tension set at. I have this exact machine

@abrogard142 3 жыл бұрын

very beaut. thank you. I've upvoted and subscribed. we just got an old singer 14u12, virtually the same as the machine you've got here. It's working not too bad - we're beginners, know nothing - but it's not cutting the cloth properly at all. I guess that means it needs a new knife? doing a video on that maybe?

@rosemcdeavitt4746 Жыл бұрын

I just found your video! Thanks for such a good video on cleaning this machine. I loved how you showed what the correct tensions should look like (the Y's and U's). I am going to take a good look at mine. I bought this model used MANY years ago. What is the best way to secure the colored bands on the tension knobs. They are coming loose.

@cindybroadway4496 11 ай бұрын

Please do a video on changing the cutting knives. Ive been using my machine since 1986 and need to replace both as i ran over a hidden pin. Now it will not cut any fabric.

@AppleRepairLady 3 жыл бұрын

So this could be super helpful for me? I hope. I have a Baby Lock 428D. It was my first serger and had been stored in my sewing cabinet unused for over 10 years and when I went to use it, it appeared to be dead. one chug than nothing moving. I'm thinking now it's possible it's dry as the desert. The old serger isn't worth anything of value, but it has value to me. I'm going to at least get it open and look at it. If there is anything special about these old sergers I should know I would love some input if possible. Loving your videos. This is awesome.

@sandraclements8438 4 жыл бұрын

Thank you so much for this video. I was given this machine. It was sewing fine and then it locked up on me. I opened up the machine and found that the needle bar assembly had a part slipping to the left and hitting against the cover that would cause the wheel to stop when the part hit the cover. I took a screwdriver to move the part to the right which worked temporarily, but when I sew, it manages to slip back to the left and jam again. Any thoughts? I would add a picture of the part but can't figure out how to attach it here.

@ariellevator 2 жыл бұрын

I have this exact serger and came to this video for help with my tension as I’m having the same issue that the looper thread won’t reach across to the leftmost needle to form a fully locked stitch. How do you adjust the looper? Seems all the pieces that loop aren’t adjustable on this model. Trying to look close at what you do but it’s inscrutable. Thank you

@bluetuber501 Ай бұрын

I have this issue, too.

@lindaduhe5355 2 жыл бұрын

Hi, I'd like to see a close up of how the lower looper thread is threaded. The manual mentions a hole on that bar and the thread going in the groove from left to right, but I don't see the holet and so not sure if mine is threaded correctly.

@rosaliepingree4198 3 жыл бұрын

Your video is very informative! I just my friend's mom's Singer 14U46B, but can't find any information online regarding this model as to when it was manufactured. I hope to find out when it was purchased. I will have it services at a local service shop. Are there any tips you can give me to make sure the service is thorough? Many thanks, Ro - Pittsburgh

@TheBozena59 4 жыл бұрын

Great video. Thank you very much. Very interesting to watch. I would like to ask you why my Surger is vibrating on top speed?

@SewingMachineRepairGuy 4 жыл бұрын

I would recommend pulling it apart and cleaning it really well, see if that helps.

@lydiahammond9605 3 жыл бұрын

I have my grandmothers and love it but it started looping on the plate rather than the guide needle. Any tips you can give? I can’t find anything on this

@mindalugo8532 3 жыл бұрын

Gracias por la clase,, soy de Puerto Rico y tengo una máquina de esas,, Como podría arreglarla

@Ingrid-fh3qu 2 жыл бұрын

How do you clean the discs on top?

@pamperedchanel 4 ай бұрын

How does the wick to the bearings go? I opened up my 14u12 and that wick is just hanging out. Appreciate the help and the video!

@2626firefly 4 жыл бұрын

Would you recommend cleaning like this for anyone buying a used serger? And when you said the wick was dry, did you add any oil to that?

@jodyashmus8730 2 жыл бұрын

I just came across your video but installing needles was so fast. I am having difficulty getting both in. As soon as I get one in & start the other one falls out. Any suggestions would be gratefully appreciated. As I am.ready to toss it out as I've bent needle on the inside 2xs

@lrdnvdv 7 ай бұрын

i wish you would do a very detailed video

@user-rh4um4vy5g 11 ай бұрын

I liked your video. I have not used my surger in years. My blade is in horizontal position and I cannot move the bar to get it into a vertical position besides oiling it do you have any other suggestions. Thank you

@RebeccaKnight927 3 жыл бұрын

Do you have a link for the magnetic bowl that'd be very handy!

@heatherrandle1307 2 жыл бұрын

I just got a 14u44 from a garage and it seemed to be in beyond perfect condition (not a single piece of lint). Which I didn't realize until i followed your video to take it apart and clean it up. My question is the looper cover seems to be hitting the arm the operates the blade. is this just a flaw with the machine or does something need adjusting? Any help is greatly appreciated as I am struggling to find any answers on my own.

@Iheartlongdongs 3 жыл бұрын

Hey! Thanks for the video it helped me out a bunch, can I ask what the settings ended up being on for the machine tension?

@karenpaul4594 Жыл бұрын

my same thoughts?

@bluetuber501 Ай бұрын

I'm interested also. . . . and we get "crickets (no response)" . . .🤔

@karima_MK 3 жыл бұрын

Hello. Do you know if parts can be sold for such machine ?

@andreatorres6575 2 жыл бұрын

Where you at ??? So I can bring my Serger Ultralock to get fix.

@jessicamann684 Жыл бұрын

I own one of these machines. I took it apart, cleaned and oiled it, adjusted the loopers back to factory spec, gapped and alligned the loopers to the needles and eachother. needle height is correct. I'm still having a problem with the lower looper occasionally missing the left needle thread when sewing fablic. Though when fabric is not present, it grabs both needle threads and chains all threads without any problem whatsoever. The clearance gap between the lower looper and needles is a close to zero as I can possibly get it. I cannot figure out why it misses the left needle thread with fabric present. I cannot get the lower looper any closer the the needle. I alligned the far left position correctly to the needle down state, then made fractional mm adjustments to get the best results, but still have problems missing when fabric is loaded. SMRG, what do you think the likely causes are?

@scottysimino8914 Жыл бұрын

Mine does the same thing . I’ve seen videos of others using this same machine and the left thread was skipped on their videos . Can get mine any closer either .

@gaabrieLa91 4 жыл бұрын

I just got this serger and needs a good cleaning! Where are you located? I don't think I can do this!

@SewingMachineRepairGuy 4 жыл бұрын

Check out my website in the video description.

@eyeonart6865 3 жыл бұрын

Why I do not use a serger, three to 6 spools of thread. Threading is a nightmare. My quantum 9960 has a overlock stitch that does a great job! Any electronic machine has an overlock stitch.

@RebeccaKnight927 3 жыл бұрын

But they don't trim as they go! They are a bitch to thread but once you get it right they save so much time!

@teresakorosec4696 3 жыл бұрын

Is there to quickly fix this misalignment? Happened during storage but it hasn't even been used yet. Left hand needle hitting metal base that sits on top of material, so it can't be used at all.

@teresakorosec4696 3 жыл бұрын

Everything is still straight. But it's like the untire needle bracket shifted to the left.

@teresakorosec4696 3 жыл бұрын

I wish I could add pictures in the comments. It's completely new, clean, and unused. I tried it out once on an inch of fabric when I first got it. And it worked like a gem. But dumb butt over here (I'm the dumb butt) had the bright idea of not storing it in its original box to save space. It's been in storage (covered so no dust) for almost 2 years. But it's been crammed with other stuff.

@rodstark 10 ай бұрын

I'm curious to know, isn't this machine a 2-4 or mock chainstich machine? It shouldn't look like a 4 thread seam like that

@SoleyDuran-eb1vh 3 ай бұрын

Necesito saber la informacion Española cómo ago?

@ThisIsStyles 4 жыл бұрын

Where can I order the needles ?

@SewingMachineRepairGuy 4 жыл бұрын

Needles for these machines can be found on amazon, eBay or sewingpartsonline.com

@ThisIsStyles 4 жыл бұрын

@@SewingMachineRepairGuy OK.. thank you!

@luzmarina596 Жыл бұрын

traducir en español, por favor.

@gaabrieLa91 4 жыл бұрын

Any idea why my serger is cutting the threads?

@SewingMachineRepairGuy 4 жыл бұрын

Make sure you are threading it in the proper sequence. Also, the tension may be too tight.

@gaabrieLa91 4 жыл бұрын

@@SewingMachineRepairGuy is it 3 in all too tight?

@SewingMachineRepairGuy 4 жыл бұрын

Follow the instructions for setting the tension from the video, I also have another video about serger tension. There also could be many other causes to your issue, it is near impossible to list them all here.

@gaabrieLa91 4 жыл бұрын

@@SewingMachineRepairGuy thank you, will check that