Which Impact Socket Adaptor is the Best? Who has the Strongest one?

Рет қаралды 715,795

Күн бұрын

Which Impact Socket adaptor is the best? We test 14 different brands from Craftsman, Husky, DeWalt, Warrior, Bauer, Hercules, MasterForce, Makita, Ryobi, Hart, Milwaukee, Tool Shop, Ace Hardware brand, and Rock Hard. So many different brands were tested and we’re gonna tell you exactly which one is the strongest out of all these. We will also tell you the price points on each of these items.
We would’ve tested a couple more brands but we were looking for what items are readily available in or around regular size cities big box brand and hardware and local supply companies. I apologize that we did not have Gray pneumatic, Kobalt, Irwin, Bosch and a few other brands.

Пікірлер: 668

@stans5270 4 жыл бұрын

ALL but 6 adapters broke at the hex end which is the narrowest point on the adapter, therefore the weakest point. The 6 that broke in the middle have their narrowest part somewhere in the middle, saving the hex end from twisting allowing easy removal from your tool. Although the test gives an accurate representation of the strength of materials, the torque achieved from the ratchet is different than the impacts from an impact wrench, so in the real world, your mileage will vary. Makita 79.2 Husky 75.7 Masterforce 71.0 Dewalt 69.7 Craftsman 69.2 Toolshop 68.9 Rockhard 65.4 Warrior 57.4 Bauer 54.6 Ace Brand 54.1 Hercules 53.5 Milwaukee 49.5 Ryobi 41.9 Hart 40.0

@ClientGraphics 4 жыл бұрын

Thank you @Stan S for putting the list together from the end of the video to recap the data.

@Fee.1 4 жыл бұрын

ClientGraphics so what I’m curious of is...take a dewalt or Milwaukee bit or adapter that’s offered in a normal “torsion zone” variety” and then one that’s the same length (2” or 3” etc” but that’s also offered in the “double torsion zone” length) and see what the difference is ...ideally from both a hand tool and an impact if possible.

@Fee.1 4 жыл бұрын

Stan S I wonder how hard it would be to quantify how much torque each hammer action from an impact imparts on a fastener etc.

@stans5270 4 жыл бұрын

@@Fee.1 With the right equipment, probably not hard at all. Most likely an engineering school has what would be needed, but it's highly unlikely results will show up on KZfaq.

@philipbucheit233 4 жыл бұрын

What if you used a small 1/4 socket instead of a deep socket. It looks like it supports more of the shaft than an impact does. And short adaptations will have higher numbers because they have more socket support.

@jinbeiktr208 9 ай бұрын

I used kzfaq.infoUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell

@jackkdaiker380 3 жыл бұрын

the only problem with this experiment it that those adapters are made for impacts not straight torque

@ChiefDLK 3 жыл бұрын

My thoughts exactly.

@madalinnicolae5594 3 жыл бұрын

@@ChiefDLK which one do you guys think its best to buy? I am working in curtain wall and I need some good adapters that will stay in the socket! and not get loose after the 3rd bolt tight, any good brands? I am UK based

@ChiefDLK 3 жыл бұрын

@@madalinnicolae5594 Any of these will do what you need them to. They are intended to be used on an impact driver. None of the impact drivers out there are strong enough to break these at least not immediately maybe over time. If you put them in a drill then you could possibly twist them off. The impact driver has more to do with them staying in the chuck than the actual adapter. Personally, for what these are used for I would just buy the cheapest one. I have some Milwaukee sets and they are good.

@madalinnicolae5594 3 жыл бұрын

@@ChiefDLK sometimes the adapter comes loose from the socket, even if its a good socket ( i use mostly elora with the impact hole inside) then if u work at heigts, u risk of them falling down! and hit someone, would u think an impact wrench would be more beneficial for my work?

@JohnSmith-qr4vt 3 жыл бұрын

Jackk- check out project farm. He did this test with an impact drill. This guy (by what the package shows) tested impact and non impact on straight torque. Project farm tested both impact and non impact rated in an impact. Neither seemed to test kobalt. I like kobalt and am curious if im just lucky or if they are worth it for the price. But neither test kobalt at all.

@Ops535 4 жыл бұрын

All grown man has same hobby : We like to see things made, and we like to see things break.

@AddictedtoTools 3 жыл бұрын

Damn straight! Aha

@Jihadbearzwithgunz 3 жыл бұрын

Absolutely

@LilasTools 4 жыл бұрын

Sad for Milwaukee..... proud of the Makita and Husky!

@jamesphilippi6143 4 жыл бұрын

Agreed. All 3 are my usual go to's

@cristhmc1 4 жыл бұрын

I had my money on Milwaukee SMH

@errolflyne4630 3 жыл бұрын

exactly mam. ill go buy makita tools. it deserves. dewalt also great. and all here will do good i think, because any tool that serves 10^6 cycle is accepted to conform the infinite life expentancy.

@jeffparker360 4 жыл бұрын

This one of my favorite torture test videos this year. Great job bud!

@masterxiong7368 4 жыл бұрын

Awesome to see the two brands I usually got with in regards to bits and extensions. Masterforce and Husky. Nicely done.

@keylimeguy9248 4 жыл бұрын

This is a fascinating test👍 I can say although they pooped out on this sort of test my Bauer adapters have been used for harsh automotive work these past 8 months and have held up great so far!

@eimartin 4 жыл бұрын

I have the Ryobi ones and used them a handful of times. You just sold me to go out and buy the Husky ones and Ryobi adapters will be the back ups. This was a great video!

@johnnyvasquez4605 4 жыл бұрын

Wow I have to say that Im pleased to see this comparison! It actually fits into my own experience. I use DeWalt Impact drivers and wrenches, but before I got my 1/2' Impact wrench I just used the driver with Milwaukee bit drive attachments. I broke 3 bits using them. I switched to Husky because they were cheaper and to my surprise they never broke on me! I had some DeWalt that I never had used and tried them and they worked great as well. Husky tools in general have been a great value to me and my work.. Milwaukee might make great power tools but their bits are terrible in comparison.

@xephael3485 4 жыл бұрын

I thought this was a @Project Farm video to begin with 😂👍

@jackiechan_wtf4041 4 жыл бұрын

Project farm : As always, I never accept product endorsement.

@ClientGraphics 4 жыл бұрын

Jackie chan_WTF No worries about that, no product endorsement just ask for your comment and like and subscribe support👍🏻

@treerat7631 4 жыл бұрын

@@ClientGraphics mastetforce did really well and so did Mendres cheaper line too shop 🇺🇸😎🏒🐧

@babybigtymer2000 4 жыл бұрын

He's completely unbiased and does a fair test across the board.

@gizzyguzzi 3 жыл бұрын

same result. Just don't buy the ones with the skinny color band in the middle. They are crap.

@itkills9251 4 жыл бұрын

Subbed, thanks for taking your time to test these out. Helps everyone greatly

@Davidriveraz71 4 жыл бұрын

I’m glad I picked up the husky 6 piece set.

@jamesphilippi6143 4 жыл бұрын

Cool video and good idea. Some surprising results. Impressed with Husky. Expected more from Hart

@The_Adventure_guild 3 жыл бұрын

Thank you for taking the time GREAT video bud!

@JohnBrinkPhoto 4 жыл бұрын

Thanks for testing. I've been using the Makita brand phillips bits with good luck so I'll try their adapters also. I've also purchased a set of quick change nut driver bits that should transfer more impact to the bolt or nut heads than a socket on an adapter.

@CP-pb3pj 4 жыл бұрын

Makita refuses to disappoint me no matter what I use.

@AddictedtoTools 3 жыл бұрын

Makita bits are great. They’re gold range of impact gear is almost unbeatable.

@coreycaudle4972 3 жыл бұрын

I love my Makita setup.i swapped over from Milwaukee,just wasn't impressed for Milwaukee's price point

@CP-pb3pj 3 жыл бұрын

@@coreycaudle4972 I’m happy with my sub compact 18volt multi tool kit from HD. Came with a Drill, Impact Driver, Recip Saw, Battery Charger, (3) 2.0 Lithium Batteries, and a Makita Tool Bag. I think I paid $299. I’m happy!👍

@coreycaudle4972 3 жыл бұрын

@@CP-pb3pj I just ordered the Makita XT268M comes with 2 4ah Batts,hammer drill,and 3 setting impact and man! I am impressed.i build catering truck cabins for airline companies so I am using both at least 8 of the 10hr days,and they're beasts

@CP-pb3pj 3 жыл бұрын

@@coreycaudle4972 Nice! They are for sure reliable workhorses. I used Makita in the past at my work and have no complaints. It’s a solid platform the will last you for years.

@ghumphrey85 4 жыл бұрын

Great video sir. I literally break these on a weekly basis. I was using the dewalt, but I’ve switched over to Irwin and Mac tools from the tool truck. They both seem a little better. The husky I’d say is pretty impressive. I’ll have to grab a set soon. Again, thanks for the video!

@torodaman 4 жыл бұрын

The Makita adaptor that's the one i bought the other day and been using it with my M18 Milwaukee impact gun and im very happy with it....thanks.

@Andrius-Lithuania 7 ай бұрын

Thank you for your tests.

@rangi69 4 жыл бұрын

Great informative video to the point glad I picked up the husky set!

@toolhead147 4 жыл бұрын

Great torque test!

@wcsd9577 4 жыл бұрын

The Makita is the same exact socket adapter I use at work that was included with an SAE socket set. I've had it for several years and it outlasted a couple different impact drivers, I currently use it with my M18 Fuel Surge. I have not been nice to it either and it's still going strong. Glad to see I made a good purchase choice.

@robworbington 3 жыл бұрын

Glad to see a review on this.. Something else that's important is where it breaks. It's a real pain if it breaks down inside the collet. I had to send my milwaukee back to the company the last time one broke on me.

@croneous 3 жыл бұрын

Awesome glad I found this video every adapter I’ve used I’ve broke with my impact

@ianvaldivia1993 4 жыл бұрын

This is an awesome review man iv been looking for someone to do it kickass!!

@ClientGraphics 4 жыл бұрын

Thanks for watching and commenting🛠🔧

@peterxyz3541 4 жыл бұрын

Glad you made this vid, am in the market for a set.

@LittleMoes_Motivation 4 жыл бұрын

Great video, great information!! Thank you!!

@skandats 4 жыл бұрын

Similar tests with 1/2" breaker bar and extension would be an awesome video!

@clutch182 4 жыл бұрын

I have had the cheap harbor freight ones for years with out any issues. I also only do diy but still they are pretty good

@holygod3737 Жыл бұрын

Thnx u guys for doing all these test

@sixtyfiveford 4 жыл бұрын

Fantastic Demo.

@cloroxbleach4980 4 жыл бұрын

Bought a milwaukee gen 3 impact and snapped my existing socket adapter so this was very helpful haha

@PBS-nm1uu 3 жыл бұрын

great presentation thanks for all the info.

@tonymitchell1094 4 жыл бұрын

Great video bro that gearwrench ratchet must be pretty awesome as well

@rmr5740 4 жыл бұрын

You're providing the working man a valuable service, thanks.

@Shaun-ey8sr 4 жыл бұрын

YES MORE IMPACT ATTACHMENT TESTS. I USE AN IMPACT ALL DAY EVERY DAY AND I LOVE SEEING VIDEOS LIKE THIS. I DO SHEET METAL WORK SO IF YOU COULD TEST 5/16 IMPACT NUT DRIVERS THAT WOULD BE A BLESSING

@likeaboss882 4 жыл бұрын

having used milwaukee, ace and others on my dewalt 887 and breaking them, i tried the humble makita bit... still havent broken it well over a year in.

@HaynesJP 4 жыл бұрын

Def going to have to get some of those! I break a couple a month.

@salg500 4 жыл бұрын

Yeah but drop your impact and lands head first and those makita bits bend super easy

@salg500 4 жыл бұрын

@Harry Dick I've had 1 milwaukee bit shatter on me. I mean, I do electrical and don't put my bits through the strain mechanics do... but still, a bent bit holder is useless when driving thousands of screws

@kokopuffs5789 4 жыл бұрын

@Harry Dick You should try their power tools. They are the best

@martinsb1221 4 жыл бұрын

i may give them a try now. HF warrior lasted me 1 month of daily heavy equipment mechanic use. Plus their 1 inch too long for my liking and milwaukee last me about 6 months at a time. I use one of the 60v batteries which gives me a little extra umph on a brushless 1/4 dewalt

@hopsonz28 4 жыл бұрын

Great video comparison

@Fish6699 3 жыл бұрын

Thanks for the Video. I appreciate the time and effort it took, I hope you make more in the future. I’m not trying to Bash you or “Hate” on the Vid or you BUT, I have to agree with the handful of people that point out this “Test” doesn’t mean much or at all in the context of “Impact” Tools. The Physics are very different between Applied graduating Torque and Bursts of constant Torque over time. I believe the results could be much different using the Tools as they are meant to be, and Will be used in a “Real World” application. I wouldn’t put a Hardened Adapter on an Impact Driver and I don’t try to Torque down on an Impact Adapter.

@edwinsandiego3435 3 жыл бұрын

A lot of good information thanks

@loktom4068 4 жыл бұрын

My cheap set lasted me over 15 years without any problems. Today still functioning as it should.

@Adventureswithmike1 4 жыл бұрын

This was a very good test ...I had a Milwaukee 3/8 socket Adapt or break getting stuck in my makita impact.. That I could not get out I had to get a drill bit and drill it out.. And I used a cheap Black and Decker drill set from Walmart and I drilled right through the metal like it was nothing... It since that day I have thrown all of my Milwaukee bits in the scrap bucket . And went out and bought makita gold

@statefarm9998 4 жыл бұрын

Good test of the dynamic/yield strength. Not so much of an impact/shock load test. It'd be interesting to see if some of these adapters would out preform in a different test

@chrisp7277 4 жыл бұрын

This. S2 tool steel at for example a mid-low Rc of 45 might perform worse than Cr-V in this yield test but be a far superior impact bit over time in one case.

@TheMaddoxfam 3 жыл бұрын

I came to say the same. Your hex socket adapter doesn’t receive a constant load, it takes impacts or short bursts of load. We use the Milwaukee and Dewault on impact drivers that have 150-200 ft lbs of torque without failure. Now... his test DOES show relative strengths. The reality is that when using in an impact driver, even the cheapest will perform much better than his testing N

@marcvought 4 жыл бұрын

Great video, good information. Thanks

@amoscardoza5253 4 жыл бұрын

Cliensgraphics sharing knowledge!! Thanks brother!

@mrbiggslove 4 жыл бұрын

Your testing was great I have used Ryobi,Dewalt, Milwaukee and the Makita gold and the Makita gold is the best one.

@dumbdabbingdad 4 жыл бұрын

Bought a set of the Husky adaptors a few weeks back. Been using them for car work. They are tough and a great bargain.

@rodw 4 жыл бұрын

First once again I want to say Happy New Year to you and Amy ❤️ !!! Great video 👍👌 I was surprised by the Milwaukee. Master Force for the WIN !!! Nicely done Menard's 😅😂 Thanks again Chris for sharing your thoughts and videos, Rodney

@ClientGraphics 4 жыл бұрын

Thanks for watching and commenting Rodney👍

@LemonMan_Man 4 жыл бұрын

The makita impact sockets are amazing I use them all the time year round only broken the 13mm so far after hanging on it

@weeklyone 4 жыл бұрын

I was looking at the Husky ones today. I liked the price for $9.99.

@joehunt3512 4 жыл бұрын

I use husky tools for alot of stuff around my millwrighting shop....I cant justify spending big bucks on high end tools when my husky have never let me down. And I'm not scared to break them

@weeklyone 4 жыл бұрын

@@joehunt3512 Same here! I tend to buy on what makes sense for the money regardless of the name brand.

@duanegeorge5370 4 жыл бұрын

Great test, and for that I thank you. I was hoping to see you test the IRWIN impact socket adapter. I'm confident it'll withstand more torque than all of those. I'll be waiting for an update 😁

@ClientGraphics 4 жыл бұрын

Duane George Sadly no big box or local supply company carried the Irwin adaptor in-store otherwise I would have had one in the lineup.

@34dawgsgo 3 жыл бұрын

The warrior HF brand 1/2 inch snapped on me today using it on golf cart wheels. Will try the Makita. Thanks for the review.

@ClientGraphics 3 жыл бұрын

It happens. Hopefully you were able to get more than a few uses out of the HF one.

@34dawgsgo 3 жыл бұрын

@@ClientGraphics I learned it's good to have a backup spare of this valuable tool. Thanks again.

@frescofranko 4 жыл бұрын

Great video !

@juanvelasquez9114 Жыл бұрын

great video for what to know we can buy and not waste our money!! thank u sir!!

@tanhuynh1646 4 жыл бұрын

Useful clip . thank you so much !

@floobertuber 4 жыл бұрын

I'd really like to see this test repeated with an repeating-impact type of load, rather than a hand-applied, continuous-torque type of test. After all, they're for using in an impact driver, correct? Otherwise, still a very interesting test for exposing overall bang-for-the-buck and general steel toughness.

@Doublethizzle 4 жыл бұрын

I wish I had read the comments before posting because I too am wondering if the two actions would produce similar results for their different tests. But, as a group of tool people, can we agree or disagree that this test tells us how well it works as an impact?

@pete_lind 4 жыл бұрын

These bits failed under torque thats about twice , what you put 12,9 hardness bolts under , its pure material strength of steel . Most likely manufacturers of impact drivers are not telling real figures of the torque their impact drivers deliver . Did see one test where Milwaukee had 50 ft ibs machine and it was just as good than Dewalt or makita that claimed deliver round 150 ft ibs . Also impact wrench and impact driver is basically same machine , still impact wrench is bigger even if on paper it has same torque output than a impact driver .

@bretunderhill 4 жыл бұрын

My thoughts exactly just like cr-va is hand tools as cr-mo is meant for impacting

@davidpowell3347 2 жыл бұрын

would do even worse?

@h8GW 2 жыл бұрын

YAAAASSS.....while none of these adapters can handle the max static torque from even a low-torque gun, I'm wondering if the connection points allow for some kind of resonance striking to allow more load to be applied. After all, I've seen TTC put many of their adapters into the 200ft-lb range...

@EcoMouseChannel 4 жыл бұрын

I've been using the Warrior ones for years. I've never broken a single one, just lost them all the time. Which is why it's never occurred to me to ever pay more for a brand name one. But I might pick up the Husky brand because I really would like some long adapters.

@jarrodbrennan121 4 жыл бұрын

Same. I got the 3 piece warrior set and still have them. Had them for about 3 yrs. I now have the ridgid 1/2in impact wrench for heavy duty stuff. Id be surprised if i ever break the warrior adapters

@Jonathan-tb6fm 4 жыл бұрын

Same. Works every time lose them all the time

@CHIBA280CRV 3 жыл бұрын

Fantastic job thanks

@seephor 4 жыл бұрын

I got the husky one on black friday. However, I've completely moved to using a 3/8" 20v impact since I find the 1/4" adapters reduce torque and add extra length. Awesome video and great work.

@ClientGraphics 4 жыл бұрын

You definitely can lose a lot of torque with an adaptor when using impact tools. In some basic testing, these adaptors on that Ridgid impact could push a fastener over 100 ft-lbs however for longer-term use moving to a 3/8" or larger impact is the best move 👍

@carloscabrera2902 4 жыл бұрын

I use husky and so far those tools been working amazingly

@lamesalegend 3 жыл бұрын

good demo, tire all pretty close. My experience is that Grey Pneumatic and Titan (super short) have held up the best for me. But they can break just a bit better than the desalts I used to use

@upsidedowndog1256 4 жыл бұрын

I only bought the Warrior set because it was on sale for $1.99. I am glad I did now.

@Mixwell1983 4 жыл бұрын

Same here and i use em in my impact all the time, never had any issues and Im glad they performed as well as they did considering price.

@ugafan1779 4 жыл бұрын

Good video and informative. As a suggestion for a later "update" video I would like to see you include/test some of the German brands to see if they are really worth the price such as Wera, Wiha, Felo, Gedore and Hazet but also Lowes staples Kobalt, Bosch and Hitachi. Great video.

@Humppa800 4 жыл бұрын

Hitachi (Hikoki) is japanese brand.

@ugafan1779 4 жыл бұрын

@@Humppa800 And? Your point is what? It is a brand that Lowes carries and sells along with Kobalt, Craftsman, Bosch (a German brand), Dewalt (an American brand). I'm not following your point?

@tyronekim3506 4 жыл бұрын

Thanks for testing Husky. I bought a set and I now know the limits.

@ClientGraphics 4 жыл бұрын

Glad I could help. It was a fun video to make!

@matolittleelkwells5377 4 жыл бұрын

I just bought the Harbor Freight Warrior set for $1.99 with coupon or $.66 cents a piece so apparently the most bang for your buck goes to Harbor Freight coupon advantage I also purchased the Husky set for $9.88 and looking forward to using them

@crazedpaul9836 4 жыл бұрын

same here i will buy the husky but i have like ten of these floating around i have yet to break one in my impact drivers for 1.99 on sale you cant go wrong.....

@martinsb1221 4 жыл бұрын

those lasted me about 1 month and their 1 inch too long for my liking

@JJ-lu6mg 4 жыл бұрын

Nice test 👍🏼👍🏼

@4leddy797 4 жыл бұрын

Pretty good test, but would rely on the Yield results vs the post break.

@eddies8527 4 жыл бұрын

Thank you for your help on this video

@jrelectrician4387 4 жыл бұрын

Thank you for the info 👍👍👍👍👍👍👍👍👍👍✌✌✌✌✌✌👊🏼👊🏼👊🏼👊🏼👊🏼✊✊✊✊

@brandonrodgers2479 4 жыл бұрын

Very interesting video!! Im interested as to how the impact rated adapters work with the skinny "torsion zone". I have some from ryobi but maybe constant torque from the ratchet isnt what those were designed for so it seems like they are worse than they are. Idk, but eye opening either way!

@tinksfawn08 4 жыл бұрын

Thank you for providing that data/info. I had picked up that Husky set just shortly after all the deals were displayed, prior to Black Friday. Great to know I got a decent deal!

@hollowpoint357sw4 4 жыл бұрын

Thank you for this test I really appreciate it. Would have beennice to list the prices on the list as well. But thanks anyway for this. ( not trying to bag on you love your channel).

@davidbuckner6454 4 жыл бұрын

Love these vids

@ClientGraphics 4 жыл бұрын

Thanks for watching and commenting!

@Wongburger 4 жыл бұрын

Just started my power tool array... picked Makita. I think I chose well!!

@CaseyA. 4 жыл бұрын

Nothing bad with Makita

@joeldavis7103 8 ай бұрын

The DeWalt adapter definitely does what I need it to do😎🤘

@boosted2.4_sky 4 жыл бұрын

The first adaptors I ever bought were Warrior...I primarily use Dewalt bits and adaptors now... but, I've had my Warrior adaptors for ~6 years... only broke one about 3 years ago.. never broke a Dewalt ....👍 I do have a set of Wiha Terminator bits that are awesome too....

@Coxfame 4 жыл бұрын

Thanks for the video. To be honest I use worrior brand for it's price, I'll grab husky next time.

@chrisrouse2086 3 жыл бұрын

Great video. I can not find the husky socket adapters online. Maybe i will get lucky during the holidays.

@mewtwosdad2230 4 жыл бұрын

Fairly new subscriber and your videos are excellent and this was great quality! Love that you made sure to break all of them. No prisoners!

@ClientGraphics 4 жыл бұрын

Thanks Anthony I appreciate you commenting and the positive encouragement is always welcomed.

@nestorroman2694 4 жыл бұрын

Great video 👍 sir. Do neiko adapters

@jsolis404 4 жыл бұрын

Great vid Was just wondering the same thing just got a kobalt impact

@georgeferlazzo7936 4 жыл бұрын

Hello again Chris, All I can say is WOW! What a surprise in the results. Another Great Video. Thank you

@DillonCleans 4 жыл бұрын

I use the Hart bits and I love them. I use them a lot but don’t use them extremely hard. They are great in my opinion

@photonashville 4 жыл бұрын

Excellent content. This is what makes youtube worth it.

@ClientGraphics 4 жыл бұрын

Thank you, appreciate you watching and commenting!

@zackphillips6648 4 жыл бұрын

Excellent but completely inaccurate to real world usage with an impact driver

@mrfender5001 4 жыл бұрын

I bought the craftsman set on amazon for $11. Great deal!!

@danr1920 3 жыл бұрын

I have a cheap one that twisted. Looks cool! For reference, my Accord wheels call for 80 ft/lbs.

@FormerlyOn2Wheels 4 жыл бұрын

I’ll still use Milwaukee. They have been great for replacements even outside warranty.

@AddictedtoTools 3 жыл бұрын

It’s always good when brands are willing to look after their customers👌

@kingsporttoolreview8703 4 жыл бұрын

One of the best videos you've ever made (In my opinion). Sometime After the Christmas/New Years season, I Would love to hook up with you via Email to help you finance a similar test with Torx bit sockets . (Craftsman. Snap-On, Carlyle, GearWrench, Pittsburgh . . . yeah, let's throw them all to the wolves and see who survives best.

@ClientGraphics 4 жыл бұрын

What size were you thinking like a T20, T27 or T40?

@kingsporttoolreview8703 4 жыл бұрын

@@ClientGraphics I was thinking the smaller sizes they are the ones that snap and break. T10,T15 and T20

@wesboothe6507 4 жыл бұрын

@ Client graphics, can you do your awesome tests on the strongest impact socket sets with the high end companies, as well as the mid and lower companies like you normally do, please!? I love your content and work man. Keep up the great work brother!

@ClientGraphics 4 жыл бұрын

I honestly only have a few brands of impact sockets: Harbor Freight, GearWrench, Husky and some random cr-v since the Tekton set went to Justin Dow. I’ll have to think about what we can do.

@DaleLucid 4 жыл бұрын

Excellent video @Chris! Harbor Freight was very disappointing. And Husky was quite the surprise. Thanks for another great compare. What DO you do with all of that broken stuff!? LOL. You keep breaking your new toys Santa won't bring you any more!

@rubberbabybuggybumper6270 3 жыл бұрын

Been using the harbor freight Bauer socket adapters in my dewalt 18v impact. I’m an auto mechanic and use them everyday and I have never broken one.

@kingsporttoolreview8703 4 жыл бұрын

LOL! - I have 4 of the brands you tested (Milwaukee, Bauer, Craftsman and DeWalt), I also have some sets of these by some brands you didn't test like Irwin, Bosch and Greenlee. ...To be honest, I don't really have a favorite set of these, I've always felt they were all pretty close to the same (for the most part, your test kinda proved me right as the majority of these all broke within a few footpounds of each other with just a couple of exceptions)

@JDye-youtube 3 жыл бұрын

Very useful!

@Munchiie 3 жыл бұрын

Awesome video

@Mixwell1983 4 жыл бұрын

I been using the cheap Warrior brand in my impact driver and suprisingly havent had any snap on me.. I have had it to the point my impact wouldnt rotate anymore on large bolts and the adapters have held fast.. Im even talking about the 1/4" adapter I use with a 11/32 socket that I slide over my cone wood kindling wedge drill splitter. They also have em for 1.99 all the time with coupon.. 3 adapters for 1.99 is a steal.

@danielboom26 4 жыл бұрын

excelente video chico, felicidades. Un saludo desde Colombia

@jcarredondo86 4 жыл бұрын

Nice video, I went through DeWalt and Milwaukee with consistent breaks every couple weeks to a month until husky released there impact driver which I noticed had the lifetime warranty so I bought 2 and I have now had them for at least a year and..... no breaks well so much for a back up lol again thanks for the vid 👍