CNC Basecamp Ep003: Carving Wood and Acrylic
Рет қаралды 22,856
Күн бұрынCreating stunning carvings in wood or acrylic plastic has never been easier than when using your CNC router. With a piece of 3d art, a few bits and a little know-how you can create fantastic looking carvings for your next project.
For information on this episode of CNC Basecamp, check out this article: www.woodsmith.com/article/epi...
You can find the step-by-step plans for our Shop-Built CNC Router here: www.woodsmithplans.com/plan/c...
Thank you to our sponsor, Inventables.com! From side hustle to dream job, they have got what you need to design your new future-plus a motivating community to keep you growing. Check them out at: www.inventables.com/?...
Subscribe to Woodsmith to receive tips, plans, projects, and techniques both in print, and in video. It’s all at www.woodsmith.com.
Follow us at / woodsmithmagazine
www.woodsmith.com
@ForestWoodworks 2 жыл бұрын
Great project and specific use of CNC clip art. This is a great resource for CNC woodworking artisans.
@cek347 2 жыл бұрын
These videos are great. I'm working my way through them all. Keep them coming.
@peterward8776 Жыл бұрын
Square peg in a round hole at 12 mins in is s great idea with the trim router so simple great idea thanks
@LeadDennis Жыл бұрын
You are making it look so easy.
@darthvadars Жыл бұрын
Great content
@hob976 Жыл бұрын
I wish videos like this would give basics speeds & feeds... Thanks though.
@gerrysmith4493 2 жыл бұрын
Can I carve this stool project with my desktop program?beautiful project!! Thanks
@steinbierz Жыл бұрын
I am loving these videos! I am just beginning in CNC routing and have been playing around with Adobe Illustrator to work on projects. My plan is to use AI and then Vectric Aspire to send them to my CNC. I see people in online videos using .AI, .SVG, .DXF, etc., and also see a lot of CNC files offered on Etsy and other places in various formats. I am still confused as to which type of file to use (or purchase) and I know that Aspire can accept all that I mentioned. I notice that your videos offer .DXF files and am just curious if this is the file type I should be working with and also, when in AI, exporting the file to Aspire as a .DXF file. Thanks.
@bomberutkrec Жыл бұрын
what rpm did you use with the dewalt 900W? Im new on this and have the same machine but im afraid of melitng the plastics
@sawdust302 2 жыл бұрын
Are you going to show the Shaper Origin?
@DCDLaserCNC Жыл бұрын
For the acrylic job, you did not really need to screw it down to the table since it was fastened down with double-sided tape. Am I missing something as to why you fastened it down with screws?
@HarmanRobotics Жыл бұрын
It was so that he could cleanly cut the perimeter - which was inside where the screws were placed.
@sudo936 3 ай бұрын
Insurance
@sudo936 3 ай бұрын
I doesnt seem that accurate to just flip the part over and line it up on the profile mark in the spoilboard? I guess close enough?
@davidcole333 2 жыл бұрын
This is how you make mass produced crap to sell on ebay.
@airwolf61970 2 жыл бұрын
Cnc is not artisan nor is it woodworking I believe ethiclly. It should be disclosed that the art and carving were obtained using cnc.
@danmays1935 2 жыл бұрын
Actually, Chris did a pretty good job of full disclosure in the opening of this video. A simple slip of paper including that information with any sales of this step stool should satisfy your demands. While it is good to be finicky about ethical behavior, it is equally important to pay attention to spelling. (ethiclly) :-(
@apocabike 2 жыл бұрын
The title of the video makes that pretty clear
@thefilthelement 2 жыл бұрын
That's just a dumb statement, using a planer or chopsaw isn't woodworking either then
@MuscleMustang07 Жыл бұрын
lmao if you're broke just say that