Our First Upgrade - Tamiya BBX Slipper Clutch Install

Рет қаралды 15,477

Жыл бұрын

With Tamiya's BBX coming one of the 'cars to have' this year, we thought we'd do a quick video on the install of one of the more important upgrade parts - the slipper clutch.
This kit comes with everything you need outfit the stock transmission with a slipper clutch, a system you'll want if you're dropping in a hot motor!
In this video we walk you through the install, adding a few tips where needed.
For more info on this ride, check out our review of it here: bit.ly/43du5jg
Enjoy the video!
//PRODUCTS USED IN THIS VIDEO
Tamiya BBX BB-01 2WD Offroad Buggy: bit.ly/3HT1wis
Tamiya BB-01 Slipper Clutch: bit.ly/44dPNF8
Futaba BLS371 Servo:
Reedy ESC: bit.ly/3RN29Ot
Reedy S-Plus 17.5T Motor:
ProTek RC 2S HV LiPo Stick Pack: bit.ly/3Af7oPw
Futaba 4PM Radio System: bit.ly/3GVLlB6
//RC GEAR WE USE
bit.ly/2LB8xuB
//FAVORITE FIVE
Futaba 4PM Radio: bit.ly/3GVLlB6
Junsi iCharger 456DUO: bit.ly/3PQR54C
ProTek 2S HV Stick Pack LiPo Battery: bit.ly/3Af7oPw
Hitec LiPo Battery Checker: bit.ly/3rrnnsS
SkyRC GNSS Speed Meter: bit.ly/3NPzDe9
//GREAT DEALS ON RC
Specials at Amain Hobbies: bit.ly/3NQK1m0
Deals at Horizon Hobbies: bit.ly/3pWPbEO
//CHECK OUT OUR MERCH
bit.ly/3tBkQrU
//MUSIC BY EPIDEMIC SOUND
www.epidemicsound.com/referra...
//SOCIAL STUFF
Website: www.competitionx.com
Facebook: / competitionx
Twitter: / competitionx
Instagram: / competitionxrc
Pinterest: / competitionx
Notice: Some of our articles, videos and descriptions may contain affiliate links, which means that if you click on one of the product links, we may receive a small commission. This helps support the website and social media channels and allows us to continue to produce content. Thank you for the support!
#tamiya #bbx #bb01 #competitionx #tonyphalen

Пікірлер: 47

@xXYannuschXx 6 ай бұрын

I like how access to the gearbox is still relatively simple

@Competitionx 6 ай бұрын

Agreed.

@cfusername 6 ай бұрын

I still was hoping for a secret trick to get to it even faster. But it seems there is no way around taking off the rear part of the cage. ;-)

@glacialphoenix5921 11 ай бұрын

I will likely be ordering the slipper after my car arrives. This install video should make it much easier for me.

@Competitionx 11 ай бұрын

Definitely a must have upgrade for sure. Glad the video helped you out.

@rcdriver 11 ай бұрын

Nice! Installing the slipper on mine tomorrow.

@Competitionx 11 ай бұрын

Ya, pretty easy. Makes a big difference with more motor! Time to put a 10.5T in yours :)

@user-vm6gk8xy4e 5 ай бұрын

Enjoyed the video. Definitely will pick up the slipper kit for my BBX. Seems to me that should have been part of the kit. If I'm not mistaken a slipper is included with the Super Astute. To piggy back off the last comment regarding the Makita Gun...Did you pick up a driver bit set from Makita as well?? Thanks again.

@Competitionx 5 ай бұрын

Well, the BBX works well without the slipper if you're using a low-power motor. If you're going to drop in a bit more power, you'll definitely want the slipper to both help protect the drivetrain and monitor the power delivery. And yes, we picked up a driver bit set from MIP! :)

@RCBirds 11 ай бұрын

Great upgrade. Curious abot your test and experienc

@Competitionx 11 ай бұрын

Have run it twice now - once at the beach, once at a track. Both times the slipper made a huge difference in the performance, especially with a hot motor (was running a 13.5T). Definitely a first upgrade to look at.

@alexsoul247 9 ай бұрын

That top bushing on the spring looks so wrong to me in the instructions. I have installed it same as the bottom (reverse from the instructions) . It holds spring nicely, fits right in into the gearbox opening and does not touch the bearing whilst pressing against shaft nicely. It makes more sense to me that way. Runs ok and looks much cleaner. Also, you don't need to unsolder engine - you can remove it and leave it handing on wires. Less work Great video, thanks for your help

@Competitionx 9 ай бұрын

Ya, the placement of those parts is a bit wonky - we thought so as well but kept it as it per the instructions, you know, just in case it is SUPPOSED to go that way :) You are correct, we didn't need to unsolder the motor but for the sake of the video, it made it easier. Glad it helped! :)

@gael582 6 ай бұрын

Nice model ! What is the reference of the rear paddle tires you used on the thumbnail ?

@Competitionx 5 ай бұрын

If you're asking about the brand of the tires, you can see that info in the description of this video here: kzfaq.info/get/bejne/qLNxpsidvLKYj40.html

@AC-bl1rl 5 ай бұрын

I went to run mine for the first time today, and it wouldn't move, it was spinning. So I cranked it down a bit, and it still slipped. Went to try some more, noticing that it was just about bottomed out, and SNAP! The shaft broke. What the heck?

@Competitionx 5 ай бұрын

What were you tightening down on - the diff or did you have a slipper installed. If you were tightening down on the slipper, it sounds like your diff might have been loose. If it was the diff you were tightening, sounds like it was built incorrectly.

@AC-bl1rl 5 ай бұрын

I was tightening the slipper clutch.@@Competitionx

@user-vm6gk8xy4e 5 ай бұрын

Hey There...Great video, Thanks...Also, can you tell me about your Makita Screw Gun

@Competitionx 5 ай бұрын

Makita Cordless Drill - the best tool we'll ever have in our toolbox: amzn.to/3QuHfDs

@JarrettDorough 11 ай бұрын

"If you have the BBX" lol, yea right

@Competitionx 11 ай бұрын

More for future owners ;)

@markbruton-young9228 11 ай бұрын

Slipper nut is very close to the motor tabs, better be careful not to short out the motor phases

@Competitionx 11 ай бұрын

Ya, thought the same thing but since the top shaft and the motor shouldn't move, it should be ok. If either DOES move, we've got bigger problems than a short on the motor LOL

@leegengxiang2173 5 ай бұрын

Just to confirm, the slipper clutch assembly pack comes with the exact same spur gear as stock, correct? I'd like to buy a spare spur gear or maybe a spare set of pads but not the whole assembly if possible.

@Competitionx 5 ай бұрын

Yes, they are both the 86T spur gear.

@bradkalman2353 11 ай бұрын

I haven't seen many people do builds or say they got them haven't they been out since last month?

@Competitionx 11 ай бұрын

Arrives on July 20th, so just a couple more weeks.

@jonthomas8487 10 ай бұрын

I’m wondering if going with a TA06 gear differential is a better option than a slipper. That way you get rid of the ball differential

@Competitionx 10 ай бұрын

We actually loved the way the ball diff made the car feel (not necessarily in the sand though), but thought the slipper might help with the increased power we want to put in it. Plus, we didn't want to have to remove the gear diff constantly to adjust the fluid for different surfaces. Not sure how much that would of happened but, well, sometimes we're lazy like that LOL

@jonthomas8487 10 ай бұрын

@@Competitionx what I’m seeing is that so far in other reviews the ball diffs are having to be removed and tightened quite a bit just after a few runs. I guess I’ll build one and see.

@Competitionx 10 ай бұрын

Hmmm, ya, we've beat on ours pretty good and not had that issue. Yet. LOL Maybe the slipper is helping with that?

@TwinsportMotorcycles 3 ай бұрын

I'm curious what you used for the paddle tires? Sand Scorcher? Thanx

@Competitionx 3 ай бұрын

Used RC4WD Sand Thrasher tires in the front and rear (fronts are ribbed, rears are paddles).

@ryverchoy1370 11 ай бұрын

I’m confused. Is this upgrade more of a performance enhancement or a preventative factor? Hate having to go through all that work, esp soldering

@Competitionx 11 ай бұрын

If you're going to keep the motor tame (ie, something like a 17.5T), it's not really needed. However, if you're going to drop some big motor in it (say, a 13.5T or hotter), then you'll want to have it for 2 reasons: help protect the drivetrain and help manage power to the ground. Hot motors WITHOUT the slipper are just going to create a ton of wheelspin unless, of course, you're really good at managing your throttle finger.

@alexsoul247 9 ай бұрын

A tone of wheel speed is exactly what makes it so much fun. I have installed it on 13.5T anyway and tightened a bit harder. It is still a good upgrade, not as much on the performance side, but rather on longevity and care for your gearbox

@ZekeSkylar 6 ай бұрын

Sorry if asked before. What brand mini drill is that? Thanks

@Competitionx 6 ай бұрын

Makita. Best drill out there! :)

@preyingmathis2517 2 ай бұрын

Do they have a gear diff for it?

@Competitionx 2 ай бұрын

They do, part number 54471. You can find it here: alnk.to/gKPTWs7

@CharlesFlahertyB 9 ай бұрын

I'm confused, it's 2wd and has a differential, what's the point of this?

@Competitionx 9 ай бұрын

It helps provide traction to the rear of the car under acceleration. Almost all 2WD cars and trucks (both onroad and offroad), have a differential, the only exception being drift cars or crawlers.

@cfusername 6 ай бұрын

What you think about, is probably a center differential between rear and front axles. And you're right, it makes no sense for a 2WD. But the video mentions the differential between the rear driving wheels which almost all RC cars have. Usually, if someone is talking about a diff, (s)he means the on between the wheels, because it's much more common.