Complete parts walk through of our 387 stroker build (rebuild)

No video

Complete parts walk through of our 387 stroker build (rebuild)

Рет қаралды 6,405

Quarter Horse Customs

Күн бұрын

Пікірлер: 36

@itseithergonnaworkoritaint7852 10 ай бұрын

Looks like you're going to end up with a fun runner.😎👍

@QuarterHorseCustoms 10 ай бұрын

It was definitely a fun combination. We can't wait to get it going again!

@jerryburks2755 3 ай бұрын

i built a 398w or that's what it came out to be makes good power and torque

@QuarterHorseCustoms 3 ай бұрын

Heck yeah, we are about to start a 393 for Project Apocalypse for Hot Rod Drag Week

@jerryburks2755 3 ай бұрын

@@QuarterHorseCustoms my engine is in a rare car a 71 Torino

@QuarterHorseCustoms 3 ай бұрын

I'd love to find a unique car to build! Maybe the next one, we just gotta get this one ready for Hot Rod Drag Week!

@robertbruneau112 7 ай бұрын

with that intake closing early (39-44) deg your dynamic compression is high, you will need to run at least a mix of 93 and 110

@QuarterHorseCustoms 7 ай бұрын

We're running 110-112 race gas. We're getting ready to do an E85 swap tho

@jessekampegaard8491 7 ай бұрын

running a little bigger cam might have helped some

@QuarterHorseCustoms 6 ай бұрын

Definitely plan to upgrade more in the future! Needed to get a baseline to reference from.

@Reztek302 6 ай бұрын

I’m doing a very similar build. I’m sticking with 351w internals. I splurged on renegade 185’s 58cc with upgrade on springs and rocker studs. Also bought new tko 600 long before tkx was released. Been 5 years collecting all the parts. I measured 7.6685 on pushrods. I’m using same rocker arms as yours. Also summit 8902 cam hoping the factory dish pistons help with valve clearance. Any advice on oil pump. I have a high volume because originally planned on going with junk yard shortblock. But have read that it may be too much and floods heads and valve seals. At this point I’m really watching my costs. Don’t have the $$ I had a few years ago.

@QuarterHorseCustoms 6 ай бұрын

We have run Melling standard volume standard pressure on all our builds and haven't had any issues with oil pressure. However, I definitely recommend upgrading your oil pump drive shaft.

@Reztek302 6 ай бұрын

@@QuarterHorseCustoms thanks

@QuarterHorseCustoms 6 ай бұрын

Let us know how the build goes

@trtony-xe4cl 15 күн бұрын

Thanx for this info,im doing a 70s-- 351w,about the same as your's, putting it in a 76 bronco,35 inch tires,but cant decide on my cam,i want to go roller,& looking for best torque profile, no racing but great bottom end estreet heads 2.02 valves ,any suggestions,??? Thanx

@QuarterHorseCustoms 14 күн бұрын

Are you going retro-fit roller with a factory spider or link bar?

@trtony-xe4cl 14 күн бұрын

@QuarterHorseCustoms yes retrofit roller,but not sure yet which is best link bar or spider,????

@QuarterHorseCustoms 12 күн бұрын

If I were to do it, I'd get a small base circle cam and drill and tap for the factory spider and factory roller lifters.

@willwork2fish261 5 ай бұрын

Do you have to do the clearance in the cylinder walls, for this build? I might just go 351w lol

@QuarterHorseCustoms 5 ай бұрын

Yes the bottom of the Cylinder walls will need a little grinding to clear the rod Bolts.

@KrisGreenhill 9 ай бұрын

I am eye balling the Summit 303 Plus for my budget 302 for my car. How does it handle on the street? I could only find a couple of idle clips online, but it sounds mean.

@QuarterHorseCustoms 9 ай бұрын

I absolutely love it, only issue I have on the street is that my compression ratio is high so I'm running 110 race fuel so it's expensive, other than that there is absolutely no complaints about the cam!

@KrisGreenhill 9 ай бұрын

@@QuarterHorseCustoms thank you for the feedback. For the price, it looks like a real winner. I was also looking at the Trick Flow 2 or 3, but I'm extremely cheap, and the Summit looks like an even better deal.

@QuarterHorseCustoms 8 ай бұрын

I apologize for the late reply, I was also looking at those, I did the compare and for the price I couldn't argue with the summit brand.

@tonymontana4349 8 ай бұрын

Nice build what’s the actual compression ratio ? Is it 12.1

@QuarterHorseCustoms 8 ай бұрын

According to Summit Racing compression calculator it's about 11.91:1 it definitely does not like 93 octane above 2k rpm!

@tonymontana4349 8 ай бұрын

So basically it’s a track car not a street car ? I have the same build and timing is at 34 degree total on pump after driving it around timing had to come down to 30 29 and still I can hear the heat somewhat detonating somewhat

@tonymontana4349 8 ай бұрын

What timing do u run or try to run

@QuarterHorseCustoms 8 ай бұрын

15 initial 32 total

@tonymontana4349 8 ай бұрын

Gotcha nice build but to me on a street car wouldn’t it be better to run a 72 cc head to lower the compression and benefit from the build

@robertbruneau112 7 ай бұрын

e7ze-ca