Hey, if you want to Pin this comment here is the list for OEM supplier suspension parts for RD1’s from Napa. Outer right Tie Rod- SE6191R Outer Left Tie Rod- SE6191L Inner Tie Rods- SR6220 Upper Balljoints- SB6191 Lower Balljoints- SB6192 Front Sway bar link-SL6260 Sway Bar Bushing-10329119 Left Rear Sway Bar Link-SL6225L Right rear sway bar Link-SL6225R Right Upper Control Arm-1012983 Left Upper Control Arm-1012982 Left Lower Control Arm-1012980 Right Lower Control Arm-1012981 Trailing arm Link bushing- 1032946 Rear upper control arm right- 1012932 Rear upper control arm left- 1012933 Lower rear control arm bushing kit not including trailing arm bushing-W52988 Power steering pressure hose-PS029018 (This has been on backorder for awhile) but it is a OE replacement. Confirm your Year with Napa to re verify but this should be good for all 97-01 CR-V FWD and AWD these are Sankei 555’s and Ultra 8 Suspension parts Sankei is an OEM supplier in Japan and Ultra 8 is Chinese however the suspension parts tend to be as good if not better than Moog and other US companies for a cheaper cost. A few companies are sprinkled in for bushings but they are from various oem suppliers. If anyone has a question feel free to ask I can try and help I also have access to Repair Link. But now most of the oem part #’s and catalogs are available to find on Honda whole sale websites like Hondapartsnow.com

The hydraulic lift just makes it look so easy. I've been replacing suspension parts on the front end of my 99...My gravel driveway hurts lol.

Sankei 555 is available from Napa. As well as NSK bearings in case anyone is going to do this and wants O.E. Supplier parts.

awesome video. you should do a lowered crv next and street or drag race that 😁

Good video, very informative info here fella.

I just replaced the entire suspension on my RD1 a few weeks ago. I used almost all Delphi products as well. I didn't even notice if the washer on the lower control arm was backwards or if the nut was loose. I'll go check for that after coffee. Thanks for the video.

Phillip you da man and don’t believe I what to do that with out a rack or lift as some people call them. Nice job bud. Hope you get Hart to come on board.

I have truhart front upper control arms and rears. I like em. they have been great for my 99 civic ex coupe. For my crv its been been about a week and work ok. I have to replace the lowers and then the ride will be good. I need to find the lowers full intact with new bearings and all because i dont have a press. That's going to be a pain.

The first 30 second of this video is greater than 90% of the content on KZfaq

👍👍👍👍👍👍

Thought this may be a good vid to follow up on. Hoora!!! The engine swap with the 01' JDM motor went flawlessly into my 99' thanks to your videos! First crank, no codes!!! The first test drive around the block the driver side cv-axel blew out. Presuming it only needing replacement I got the same rock-auto axel you used in a previous video. Once the new axel was in I reversed a vehicle and a half length and the driver side axel boot (closer to the passenger) ripped up and now I assume the axel it toast. Any ideas what might be causing the driver axel to go bad before I take it to a shop?

I just did the whole front end(upper, lower arms with new bushings and ball joints, new struts,tie rods...) and the back as well(upper,lower arms,trailing arm bushings,new struts,new links..) on my 00, but the drivability still feels a little iffy :/ still feels like i missed something. Do you think at this stage it might be the whole subframe at both ends? *btw i havent driven it for long since i still need an alignment.

Do you know anything about scitoo suspension kit for 99 crv? Any information would be appreciated thanks.

I find that my wife's ironing board helps keep the new parts off the ground...😁

Integra sub Frame ?????? Do you have a video on that ? Also are any Honda,Integra parts compatible with 1st Gen CRV ? Thanks 👍

Hello from italy! It's possible to use oem spring from another honda to rise the cr-v? Like front accord V sedan spring (100mm diameter 485mm lenght)? I don't find anithing compatible for rear axle. Kind Regards.

Hi guys. Question i bought a 2000 honda crv awd lifted 1"1/2. And replace the upper control arms with stock. Does it affect the alignment?

Where I'm can buy the rims

Can you replace a cv axle boot only that blew out or do you have to replace the entire axle?

Boss man. Are the auto front spindle same as manual front spindle!? It’s cuz both of my front lug studs are striped and don’t feel like pressing out the bearings and replace the hub. Just wondering if they are the same so I can just find a good spindle at my local junkyard and switch it out

If you check your local pick n pull you may get lucky and find that fender for dirt cheap.

I bought Sensen Quick struts for my 97 CRV are those okay shocks or is there a better aftermarket pair I can get these seem to be not as stiff as it should be any advice would be helpful thank you and better terms car wobble side to side like a wagon because of the struts

Que amortiguadores usas?

Rockauto a best

I have one in morocco

How much would a job like this be at a shop ? 🤔

God job