How To Install Quick Struts - 97-01 CRV Suspension Removal/Replacement (ASR Rear Lift Spacer)

Рет қаралды 80,896

Күн бұрын

Buy all 4 struts here!
Front Left Quick Strut - amzn.to/2MIKlpz
Front Right Quick Strut - amzn.to/2L45YOY
Rear Monroe Quick Strut - amzn.to/2zslEoL
ASR Lift Spacer - jhpusa.com/products/asr-cr-v-...
Help support my channel, purchase decals here - garagebuilthondas.bigcartel.com
/ garagebuilthondas
My GoPro - amzn.to/2YQ3OGZ
My Mirrorless Camera - amzn.to/2HzzFFT
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for you support!
#diy #repair #maintenance

Пікірлер: 234

@seanovens8422 10 күн бұрын

I have an 01 crv as well. Coming up on 300 km. Ive seen them in the wrecking yards with half a million. Beautiful simplicity and honda quality

@rawagz9970 3 жыл бұрын

I was ready to fork out for front struts until I found your video. I was quoted about $240 per strut (+ parts) to replace and I took maybe an hour each (because I took my time). Thanks for a great video. Made it easy AND saved me almost $500!

@craiglaferrera9698 Жыл бұрын

TV óöíííkkkk KK k oh hoo úyuújjújuuújjjjjjjjjj it jújújjjjjï KBL me k lmk llllll km,

@texastrucklove5304 3 жыл бұрын

Thank you. Good call on dropping LCA to install the struts. Best video on installation! Appreciate the help!

@FUCKY0UHATERS 4 жыл бұрын

You sir are a true honda man

@kentechies8846 2 жыл бұрын

Thanks for this video!!! I was debating of getting a mechanic shop to do this and you made it look so easy!

@GarageBuiltHondas 2 жыл бұрын

You're welcome, good luck!

@Punny1234 4 жыл бұрын

Another great and easy to understand video from the Honda guru himself. Thanks Jon.

@GarageBuiltHondas 4 жыл бұрын

Thanks for always commenting even if the videos haven't been a lot of "fun" lately. 👍

@Punny1234 4 жыл бұрын

@@GarageBuiltHondas It may not always be fun but always something to learn, cheers.

@DashnCars 4 жыл бұрын

NOW THAT'S MY FETISH! Those are the same struts I'm running on the my wagon :)

@GarageBuiltHondas 4 жыл бұрын

Needs a little more lift and wheels/tires!

@DashnCars 4 жыл бұрын

@@GarageBuiltHondas ikr!

@JustinKapow 3 жыл бұрын

Found this channel for help with my crx. Year later i search for crv halo and boom. Your here to help. Thank you

@daviddahl855 4 жыл бұрын

Great videos, always helpful.

@GarageBuiltHondas 4 жыл бұрын

Thanks David

@edgarnavarro7264 2 жыл бұрын

Great video bro. Quick question, Do you know if it matters which way I install the rear Monroe struts? and also for the outer rear LCA bolt should I put some load on the rear trailing arm with my jack and then torque it down? I noticed its a tight squeeze to tighten that bolt when the wheels are installed.

@abdouallahuniverse5689 Жыл бұрын

You are rightt man. My crv is lower on the back than on the front even i install the same brand chocks quickstrut monroe, and i was looking to resolve the problem and now i found how because of your video, add spacers.

@GarageBuiltHondas Жыл бұрын

🙏

@ElSalvador1Chance Жыл бұрын

I WILL NOT RECOMMEND THIS. I did the same to my 99 CRV and the suspension felt horrible but I left them on just to have a lift CRV. My tires got wear off so fast since it’s forcing the whole suspension therefore the tires aren’t even on the ground. A year later, (exactly today) I decided to take them off and I got new shocks to keep the original height and let me tell you, that’s the best decision I made. Suspension feels Amazing now.

@GarageBuiltHondas Жыл бұрын

I'm still daily driving my CRV to this day. Zero issues and rides like stock. I'm unsure what was causing your issues. A local friend has a similar setup too with no issues and he's had his CRV longer than I have had mine.

@upfactoryracing4148 4 жыл бұрын

Yeah man I dig those AWD first gen CRVs

@GarageBuiltHondas 4 жыл бұрын

Me too, they are actually pretty fun to drive!

@jessetoptechallen1461 4 жыл бұрын

Great job

@ddb7408 4 жыл бұрын

Nice video 👍👍

@GarageBuiltHondas 4 жыл бұрын

Thanks!

@JiroProject 3 жыл бұрын

For the spacers in the back, do you need any subframe spacers as well? kinda like the hrg kit?

@GarageBuiltHondas 3 жыл бұрын

Not with a 1" drop. I didn't need anything additional. If you go higher then you may need to start adding other spacers and parts.

@williamhollie7235 4 жыл бұрын

Great job. You have helped me so much with my 88 civic LX. Would you recomend 1 inch spacers just to give me a little more ground clearence?

@GarageBuiltHondas 4 жыл бұрын

Thanks! Are you on stock suspension?

@williamhollie7235 4 жыл бұрын

@@GarageBuiltHondas yes,it's stock. I tried briefly to google spacers without any luck

@dauntewimbush1939 2 жыл бұрын

I had my Monroe struts installed for maybe two months and they are already clanking🥲!!! Maybe because I do mild off roading while hunting

@GarageBuiltHondas 2 жыл бұрын

Are you sure it's the shocks?

@jimmytuffrey6509 2 ай бұрын

Sounds like the sway bars need replacing

@yamatomusashi1412 2 жыл бұрын

excellent work dude. tnk u

@GarageBuiltHondas 2 жыл бұрын

Hope it helped!

@yamatomusashi1412 2 жыл бұрын

yes it did. thank you for video!

@johnnymack8442 4 жыл бұрын

Looks good. Site nice.

@GarageBuiltHondas 4 жыл бұрын

Thanks!

@happycustomer5934 3 жыл бұрын

I liked your video, how does it handle or look with any weight in the back? Also, where did you get the spacers?

@GarageBuiltHondas 3 жыл бұрын

Like stock.

@redpillforreal3053 4 жыл бұрын

NICE MUSIC AT END!

@GarageBuiltHondas 4 жыл бұрын

😀👍

@xThe_Caveman 4 жыл бұрын

Great work dude keep them videos rolling. U need wider tires on those stock rims

@GarageBuiltHondas 4 жыл бұрын

I really do. But I need concrete first in the backyard to make it easy for us to work on cars back there!

@xThe_Caveman 4 жыл бұрын

@@GarageBuiltHondas no rush Jon lil by lil crv gonna be hooked up

@michaeljtoney3544 9 ай бұрын

you gotta think about this ,after load out the back will drop as weight load increases,and vehicle will be more level unless its overloaded to the max!

@jermainecotton4406 4 жыл бұрын

Having the hardest time trying to get the front forks back on would have loved to see how you got them back on

@GarageBuiltHondas 4 жыл бұрын

Really? I didn't have any problem at all. It basically went back in as easily as I removed them. Step onto the rotor, it might help give you clearance. Once the fork is on, you can use a hammer and hit it up into the shock to help line it up.

@jermainecotton4406 4 жыл бұрын

@@GarageBuiltHondas I stepped on it like you mentioned and it worked better that way working on the rear now using your method of removing the sway bar Thanks again jon!

@GarageBuiltHondas 4 жыл бұрын

Awesome!! 👍

@Alan01 3 жыл бұрын

I have a 2003 CR-V. Is it pretty much the same? Also, what's going to be easier for the amateur - quick struts or the strut towers with new flange and strut mount already attached? Thanks

@GarageBuiltHondas 3 жыл бұрын

I don't believe so. That suspension setup probably looks different and may be a strut and not a shock like mine. I'd get the quick struts.

@bluedrew Жыл бұрын

Great video. Another video did too much work removing end links, and dropping lower arm. Probably best to torque lower shock bolt with weight on wheels.

@milkywey511 4 жыл бұрын

Motor mount upgrade video be super cool see 1st gen. Crv

@GarageBuiltHondas 4 жыл бұрын

I may get there. Mine seem ok still so I don't plan on changing them just yet!

@slorice8723 3 жыл бұрын

Thanks for the video. I’m wrapping up the exact job including the same 1” rear spacers. My ‘00 has 235K on the original suspension so it is long overdue. I also did the entire front suspension as well as the rear, including the dreaded trailing arm bushings. Question, my preloaded rear struts are not marked R or L, does it matter which side? They look identical but I’m not sure.

@GarageBuiltHondas 3 жыл бұрын

Nice! Doesn't matter.

@slorice8723 3 жыл бұрын

Garage Built Hondas thanks for the quick reply!

@GarageBuiltHondas 3 жыл бұрын

👍

@GarageBuiltHondas Жыл бұрын

The brand I went with is in the video. Ride quality didn't get better until I bought new tires. I couldn't tell a difference with just the shocks.

@miloren8547 Жыл бұрын

Do you know how important the rear support frame brace is? Both of mine are rusted and broke but I’m not sure how urgent this is. Haven’t seen anyone cover this thanks

@GarageBuiltHondas Жыл бұрын

Not sure which part you're talking about. If you're on Instagram send me a picture.

@rox2times Жыл бұрын

I need you in Florida John I got a 98 CRV needing this and a few other stuff done 😢

@GarageBuiltHondas Жыл бұрын

Drive it to Texas. Lol, I'm kidding. 😁

@cri8tor Жыл бұрын

Have you recorded an update video on the struts? Are you still happy with their performance? Would you choose different struts next time? Great video and thank you for sharing your experience with all of us who appreciate the effort it takes to record, edit and upload content. Cheers

@GarageBuiltHondas Жыл бұрын

Zero issues for me so far. Still daily driven.

@cri8tor Жыл бұрын

Good to hear because I recently purchased a set for my CR-V. Cheers brother

@adriand3196 2 жыл бұрын

I’m new to cars so can you replace the shocks and also lift it a couple inches at the same time? Or do you have to lift it another time?

@GarageBuiltHondas 2 жыл бұрын

You can install a lift whenever you want.

@provse5455 3 жыл бұрын

Hi. Please tell me are these new shock absorbers soft ? on a bad road, how does the car go ?)

@GarageBuiltHondas 3 жыл бұрын

The car feels exactly the same as before, well better actual because I had 2 blown shocks.

@samuelalzate8573 2 жыл бұрын

A shop here in Oregon quoted me $2,000 for a 2 inch lift. I think I might do it myself and this video helped boost my confidence a little. Could you do or do you have a video on how to replace rear control arm bushings?

@GarageBuiltHondas 2 жыл бұрын

I do not. If you don't have a pressed it might be better to just buy a new arm with new bushings in it already.

@samuelalzate8573 2 жыл бұрын

@@GarageBuiltHondas I saw a video where you can rent press kits from automotive stores. But if I can find the arms for a good price, I'll just replace them. Thanks though!

@sergiob6950 4 жыл бұрын

Great video Jon! You the man! For the rear assembly is it a pair or just one?

@GarageBuiltHondas 4 жыл бұрын

They sell them individually, but you'll need both. Those are the same unlike the front which have a L and R. 👍

@sergiob6950 4 жыл бұрын

Garage Built Hondas Great thanks!

@GarageBuiltHondas 4 жыл бұрын

Anytime!

@juanpedro5654 4 жыл бұрын

If I get the 1.5 in spacer would I still have to trim the studs

@GarageBuiltHondas 4 жыл бұрын

I'm not sure. Possibly not.

@ccjohncc1 3 жыл бұрын

Thanks. I love my Japanese made 97 and have decide to completely make it new again ( Or as close as is reasonable :) ).

@GarageBuiltHondas 3 жыл бұрын

👍

@socogremlin 3 жыл бұрын

Mee too. I've had it 15 years. Time to fix it up and make it nice

@TopClips7777 8 ай бұрын

all RD1s are Japanese made

@ianpwnz04 2 жыл бұрын

Do u need a adjustable camber kit if y have the lift kits?

@GarageBuiltHondas 2 жыл бұрын

It's smarter, but not necessary

@ifuckinghatelife2312 3 жыл бұрын

I recently bought coilovers for my crv but it sits too low for me even at its highest level. Do you think I could put a 1.5 spacer in there and the coilovers so that it doesn't sit as low?

@GarageBuiltHondas 3 жыл бұрын

Absolutely

@kevinv2307 3 жыл бұрын

Bro I was wondering the same thing my rear is to low for my liking

@GarageBuiltHondas 3 жыл бұрын

Yup, go for it

@solidsora634 3 жыл бұрын

how do those quick struts feel? as original, or harder / softer?

@GarageBuiltHondas 3 жыл бұрын

The same

@eddpna242 3 жыл бұрын

Did you have any issues installing front passenger strut? I’m trying to install mine and it keeps hitting frame

@GarageBuiltHondas 3 жыл бұрын

No, i didn't have any issues.

@daviddahl855 4 жыл бұрын

Rebuild or pick up an engine from the salvage?

@GarageBuiltHondas 4 жыл бұрын

Rebuild

@emiliodiaz9008 3 жыл бұрын

Goog jod bro where got back struts thank

@GarageBuiltHondas 3 жыл бұрын

Link in description

@lebronjordan802 4 жыл бұрын

Great video John! What year is your crv? Where did you buy your struts? I have 2002 crv and every few days the coolant is low. I replaced the radiator and it did not fix the issues. I checked the old radiator by pouring water on it and I did not see any leaks. Going back on the new radiator I don't see a visible leaks. I changed the thermostat and did not see any cracks on the housing... any tips or ideas! Thanks...

@GarageBuiltHondas 4 жыл бұрын

2001. I got them off Amazon, I left links in the description. Let it idle and warm up to operating temp and see if you can detect a scent of antifreeze coming out of the exhaust and if it feels kinda swampy. You may have a head gasket that's bad and burning the coolant out now.

@lebronjordan802 4 жыл бұрын

Garage Built Hondas thanks man I'll check on that. I also hear a whistling noise when accelerating, thinking it's a vacuum leaks. I checked all hoses and I found 2 slightly cracked or split in the end, I replaced them both and still making whistling sounds when accelerating the gas pedal...if in fact the head gasket is bad, will it make whistling sounds?

@lebronjordan802 4 жыл бұрын

Garage Built Hondas thanks man I'll check on that. It also makes a whistling sounds when accelerating. I'm thinking it's a vacuum leaks, I checked all hoses and found 2 slightly cracked or tiny split in the end. I replaced them both but whistling sounds remains audible when accelerating...if in fact the head gasket is bad, will it make that whistling sounds?

@lebronjordan802 4 жыл бұрын

Garage Built Hondas hey John I found the leak ... l let the engine idle for a long time then I started to smell a coolant next thing I noticed a coolant dripping underneath the engine. I observed a little further and I spotted a tiny hole on the upper radiator hose squirting coolant. I replaced the hose yesterday and so far so good...thanks man 🙂👍!!!

@IkarosCanFly 4 жыл бұрын

Should of threaded on your old nuts before cutting so that you could unscrew them and it would fix the threads for you.

@humanbeingfromearth 4 жыл бұрын

Smart

@churmurrify Жыл бұрын

are new axles require for 1-1.5" rear lift?

@GarageBuiltHondas Жыл бұрын

@Sinjected 2 жыл бұрын

Are these good for a long term replacement? I'm looking to replace my blown oem ones with something that will last at least a few years.

@GarageBuiltHondas 2 жыл бұрын

Mine are still working now.

@Sinjected 2 жыл бұрын

@@GarageBuiltHondas thanks for responding. How do they ride? Is it harsh or close to oem?

@GarageBuiltHondas 2 жыл бұрын

Stock

@KroomShrooms 10 ай бұрын

Hey man! I just bought these quick struts but after realizing a lot of people are leaving negative reviews about them, are they any good? Have you been hearing anything when you drive? Do you like the ride feel when you drive?? Are they lasting? Do you still have them on?? Thanks.

@GarageBuiltHondas 10 ай бұрын

Still on my CRV to this day. They feel perfectly normal to me. Daily driven until last month. My AC compressor broke and I haven't had a chance to change it.

@KroomShrooms 10 ай бұрын

Thank you for the reply!

@davidabrego3434 Жыл бұрын

Where did you get front struts? Thanks!!

@GarageBuiltHondas Жыл бұрын

Link in description

@FRJ1982 4 жыл бұрын

Where can I find those 1" spacers for the rear?

@GarageBuiltHondas 4 жыл бұрын

Here ya go! There are others but I liked these the best for ease of installation. Most others require you to use a spring compressor to rotate the top hat which I didn't want to do one bit. www.asrparts.com/products/asr-cr-v-lift-spacer

@FRJ1982 4 жыл бұрын

Thanks brotha!

@Snafu2346 Жыл бұрын

Is it okay to use anti seize on these suspension bolts to prevent future seizing when maintaince could be needed? Or is it not recommended on these parts?

@GarageBuiltHondas Жыл бұрын

Yes, safe to use on suspension.

@Snafu2346 Жыл бұрын

@@GarageBuiltHondas I appreciate you getting back to me.

@GarageBuiltHondas Жыл бұрын

👍🙏

@sistercalhoun4444 4 жыл бұрын

Hey, Bro I heard the Hondas between the year 1997 and 2004 made bad transmissions they say they don't last long for all make and model.

@2_2_4_3 4 жыл бұрын

2002-2005 K series are the most I heard but not personally.

@GarageBuiltHondas 4 жыл бұрын

I don't think that's true. My CR-V has the original transmission and has 233k miles on it. I believe it because Honda's are used and abused and people don't follow normal service intervals a lot of the time because these cars can be inexpensively when purchased used. My wife owned a 2003 Accord for 2 years and it had over 160k on it with no issues also.

@guile108 4 жыл бұрын

6:34

@filthybronco 9 ай бұрын

How does it handle with the rear slightly lifted?

@GarageBuiltHondas 9 ай бұрын

I can't tell any difference from stock. Feels normal.

@jericlee1509 3 жыл бұрын

sir , shock is it comfortable? gas shock or hydraulic?

@GarageBuiltHondas 3 жыл бұрын

Gas. Feels like stock.

@johnrathamone3261 4 жыл бұрын

He should get the Integra type-r wheels from them. looks so nice

@GarageBuiltHondas 4 жыл бұрын

Those look fantastic, the only thing that is terrible is the wheel offset. I'd have to run spacers to make them "fit" a little more nicely.

@DanielPerez-bk6lf 2 жыл бұрын

I used the 2 inch spacer from aerogenics in rear. 3 years later when changing the quickstruts the old spacer was impossible to take off. Bad design and different metal over years those hardware from asr rounded off right away. I couldn't reuse the spacer. After using penetrating oil and heat. You need a 14 thin wall socket to take off and it can't be re used.

@GarageBuiltHondas 2 жыл бұрын

What can't be re-used?

@southshore7691 Жыл бұрын

Are these stock ride height replacements?

@GarageBuiltHondas Жыл бұрын

Yes

@rubenske091 4 жыл бұрын

inner outer tie rods install???? :D

@GarageBuiltHondas 4 жыл бұрын

I'd like to get there soon too!

@TheFrogfeeder 3 жыл бұрын

So if I want to put like 1” spacers in front and 2” spacers in the back, can I put 215/75 on it and do I need to get the adjustable camber rods like I see in other videos? Also, after taking all that suspension apart, would I need to get it aligned?

@GarageBuiltHondas 3 жыл бұрын

It depends on the wheels you use also. Offset plays a major role when upsizing to bigger tires. If you don't have the offset, you may rub up front. It's suggested to get aligned after doing this suspension work. I never did, pushed my luck and it still drives straight

@TheFrogfeeder 3 жыл бұрын

@@GarageBuiltHondas yeah I’m looking more into this. I’d like to have the 235/75 tires, trying to confirm if my stock steel wheels would work. Looking to go 2.5” higher with the lift...I have no idea what these stock rims are...

@GarageBuiltHondas 3 жыл бұрын

👍

@TheFrogfeeder 2 жыл бұрын

I have all my parts, I got 1” spacers for the front too. I plan on using the stock 15” wheels, and the tires I’m going with will be 215/75. I don’t wanna have to buy new wheels, and wider tires is just more stress on steering, imo. Anyways, I just gotta run and get some locktite in the morning then it’s shocks all day till she’s done, tires and alignment on Monday.

@TheFrogfeeder 2 жыл бұрын

I got those rear lower bolts soaking in pb blaster overnight too. I already tried with a ratchet and a bar, didn’t budge.

@bluedrew Жыл бұрын

My left front strut went in fine. On R side the tab on the new strut doesn't align with the slot on the fork. Thought about cutting off the tab, but guys in a forum say I should be able to install strut to pinch fork and then somehow rotate the fork with a pry bar. I do that and then it jumps and rotates to far the other direction. Any ideas?

@GarageBuiltHondas Жыл бұрын

Cut off the tab.

@bluedrew Жыл бұрын

@@GarageBuiltHondas thanks That was my first thought. But there is a slight indent in the bottom of the strut that allows the bolt to go through. It might cause slight damage and be harder to get the bolt on if it’s not lined up with the tab. I was going to use my spring compressor take it apart a bit, but it wouldn’t fit on the springs ended up, taking it to the shop to realign the strut.

@edgarnavarro7264 Жыл бұрын

Do you think the rear was raised a whole inch because you left 3/4 of an inch on the strut tower bolts instead of 1/2 inch?

@GarageBuiltHondas Жыл бұрын

No.

@edgarnavarro7264 Жыл бұрын

@@GarageBuiltHondas ok cool, thanks for the response 👍🏽

@GarageBuiltHondas Жыл бұрын

👍

@vincentquintero8028 3 жыл бұрын

9:08 what type of bolt and a nut was it.

@GarageBuiltHondas 3 жыл бұрын

The stock bolt for the lower control arm. There's not a nut, the LCA has a threaded nut into it.

@kanibis420 Жыл бұрын

Are these better than TRQ ?

@GarageBuiltHondas Жыл бұрын

Couldn't tell you. Never used them.

@CesarsCarCorner 4 жыл бұрын

Go check out Honda Rescue Garage and see how installs the spacers. Especially for the fronts!

@GarageBuiltHondas 4 жыл бұрын

I've seen. Interesting how he kicked it in. 👍😁

@CesarsCarCorner 4 жыл бұрын

@@GarageBuiltHondas Awesome huh!? I wish I would've seen his video when I was installing my lift kit into my old CRV

@dailydrivendiecast 4 жыл бұрын

Hey, dont mean to bother but I'm doin my b20 swap this weekend into my da, any way to contact you for questions?

@GarageBuiltHondas 4 жыл бұрын

Never a bother. Right here is best and easiest/fastest for me. 👍

@dailydrivendiecast 4 жыл бұрын

@@GarageBuiltHondas so I got everything swapped over but the b20 has the knock sensor and a squarish brown plug right under the intake manifold and no oil pressure nipple. My b18 harness doesn't have anything that fits that brown plug and the oil pressure plug can go on the knock sensor but that dont seem right. Any advice? Thank you so much

@dailydrivendiecast 4 жыл бұрын

@GarageBuiltHondas 4 жыл бұрын

Lol, the KZfaq app is terrible sometimes. It won't notify me of all responses to a previous comment and I'll miss some. I hate not being able to try and help in a timely manner.

@GarageBuiltHondas 4 жыл бұрын

Still need help? Message me on Instagram if you do or email me. Sorry for missing your reply. Garagebuilthondas@yahoo.com

@seanross1589 2 жыл бұрын

If you are also installing a new lower control arm, the new bushings make it extremely difficult to line up all three holes, especially since two of them (the one that lines up with the strut, and the one that lines up with the trailing arm) will be under tension.. My suggestion is to unbolt the upper control arm from the rear trailing arm, as well as to remove the two bolts holding the rear trailing arm bushing to the underside of the car. This will release the tension on rear trailing arm which makes lining up the hole with the rear lower control arm much easier. I hope this helps someone in the future.

@GarageBuiltHondas 2 жыл бұрын

👍

@sheistybasterd 2 жыл бұрын

I am going to try this. I was unable to align the lower bolt holes for the strut, so i unbolted the lower control arm from the jack point. This gave me enough play to align the lower strut bolt, but now I cannot align the LCA bolt back to the jack point.

@seanross1589 2 жыл бұрын

@@sheistybasterd let me know how it goes. Just be careful because you will have to jack up the strut to rebolt the upper control arm and trailing arm (they are under tension when the wheel is off the ground).

@sheistybasterd 2 жыл бұрын

@@seanross1589 it worked! Thanks for the tip sir.

@seanross1589 2 жыл бұрын

@@sheistybasterd Great, I'm glad to hear it! No problem, i just want to help where i can.

@joshharmon6380 2 жыл бұрын

I've read you need to get professional alignment done after doing this job, but you don't mention it one way or another. What's your take? Thanks for the clear video.

@GarageBuiltHondas 2 жыл бұрын

Not necessarily. I didn't touch anything related to toe (tie rods or compensator arms). I still haven't to this day had it aligned.

@joshrenteria2216 4 жыл бұрын

May I ask how these have held up and if you recommend them? I’m looking into redoing the whole front suspension and see these kits by a company called TRQ but am weary if it’s worth it.

@GarageBuiltHondas 4 жыл бұрын

I love em. No issues. I daily drive my CR-V and have been since the install. I refused to buy a cheap brand being this is my daily and need parts to last and hopefully be reliable.

@joshrenteria2216 4 жыл бұрын

Garage Built Hondas thanks for the speedy reply!! Any suggestions on where to source my upper control arms, lower ball joints & tie rods?

@kevincrush859 4 жыл бұрын

@@GarageBuiltHondas Please keep us updated on those Monroe Quick Struts. I've heard so many bad things about them from every brand(even KYB) but I've read the most complaints about Monroe.

@GarageBuiltHondas 4 жыл бұрын

I have had any issues and I've been using them since August 2019.

@GarageBuiltHondas 4 жыл бұрын

Upper arms - amzn.to/2xzf6XV Ball joints - amzn.to/3azBjU2 Tie rod ends - amzn.to/3411XDa

@yamatomusashi1412 9 ай бұрын

ive seen other youtubes with fewer steps and explained better. is that possible??

@GarageBuiltHondas 8 ай бұрын

Try it.

@yamatomusashi1412 8 ай бұрын

@@GarageBuiltHondas tnk you for video. I ommited one of your steps and added one of mine. I think my way much easier.

@4000marcdman 2 жыл бұрын

2yrs later. How they holding up?

@GarageBuiltHondas 2 жыл бұрын

No issues

@4000marcdman 2 жыл бұрын

@@GarageBuiltHondas thanks. I think I'll give them a try.

@Phatty057 3 ай бұрын

The rear struts are fine but I have found that the front struts are WAY to floaty and bouncy (returning to Amazon)...Good video on the install however.

@southshore7691 Жыл бұрын

Is an alignment necessary after changing ?

@GarageBuiltHondas Жыл бұрын

They say yes, but I don't think it's 100% necessary unless you're lowering a vehicle.

@Snafu2346 Жыл бұрын

@@GarageBuiltHondas i was about to ask the same thing. Its good to know. I guess I won't now till I do it. I appreciate the video as I wasn't sure if it something I can tackle. The work itself looks simple enough, but I know nothing every goes as planned. My CR-V was a snowbelt car and I wonder if the bolts are heavily rusted or damaged. I don't have anything else but hand tools. I might pick up some power tools as I've always wanted to.

@DelFam2011 4 жыл бұрын

Lol I just did this 2 days myself, lol

@GarageBuiltHondas 4 жыл бұрын

Well you should've came over here and did mine then!! 😁

@Brandi548 2 жыл бұрын

Any subframe and trailing arm spacers?

@GarageBuiltHondas 2 жыл бұрын

@7ThrillFishing 2 жыл бұрын

If im correct, only need to if you’re going more than 2in lift

@GarageBuiltHondas 2 жыл бұрын

Yes

@7ThrillFishing 2 жыл бұрын

@@GarageBuiltHondas wait so it is recommended even if you lift 1in front & 1.5 rear?

@mel8080 2 жыл бұрын

How are the Monroe struts holding out?

@GarageBuiltHondas 2 жыл бұрын

Still no issues for me.

@mel8080 2 жыл бұрын

@@GarageBuiltHondas Thanks, I just ordered Monroe Quick-Struts for my Rears on my '07 CRV (I know your installation is different than my '07, but you have good tips). I have to do the front end in the near future. Thanks for sharing your video.

@GarageBuiltHondas 2 жыл бұрын

Good luck, hope they treat you well!

@mel8080 2 жыл бұрын

@Garage Built Hondas I just received mine through the mail. I did notice that both strut's "plastic protective/boot" was a little off centered per the actually strut, so I was wondering if they are supposed to look like that? I replayed your video to see if yours were similar, and per the 0:08 segment, your "plastic protective/boot" for the bottom strut looked like it was off centered too. Looks like one side of the strut could be rubbing against the "plastic protective/boot". Is this correct? Thanks!

@johngoepel5263 2 жыл бұрын

The sag is caused by the rear springs wearing out. The sag problem was resolved by installing new quickstruts. The spacer was unnecessary.

@GarageBuiltHondas 2 жыл бұрын

Ok boss

@montymusicioapo714 3 жыл бұрын

Bro are those suspension fit on rhd cry

@GarageBuiltHondas 3 жыл бұрын

On what?

@montymusicioapo714 3 жыл бұрын

Right hand drive CRV

@GarageBuiltHondas 3 жыл бұрын

Yes. There is no suspension difference in any 97-01 CR-V.

@montymusicioapo714 3 жыл бұрын

Thanks man ,how can I order 4 suspensions

@GarageBuiltHondas 3 жыл бұрын

Front Left amzn.to/2RCxc1R

@kirillyakunin759 2 жыл бұрын

Срузу привода приготовь все 4 новые.

@vincentquintero8028 3 жыл бұрын

Can somebody please tell me how to remove that 14mm bolt that holds the shock absorber without snapping it?

@GarageBuiltHondas 3 жыл бұрын

Front?

@vincentquintero8028 3 жыл бұрын

Rear

@GarageBuiltHondas 3 жыл бұрын

If you're having that much trouble it's probably seized into the bushing/control arm.

@vincentquintero8028 3 жыл бұрын

It is i wonder if the torch would help?

@GarageBuiltHondas 3 жыл бұрын

Absolutely.

@Shiekh420 2 жыл бұрын

how come no one ever does the passenger side tutorial

@GarageBuiltHondas 2 жыл бұрын

I'm not sure. Lol

@TheNoobComment 3 жыл бұрын

All this and you only went up an inch for the back? Is this what you expected?

@GarageBuiltHondas 3 жыл бұрын

It's what I wanted.

@bluedrew Жыл бұрын

Too much work on rear. Strut should come out without removing toe rod and dropping lower arm. Pry bar to lower it a bit and strut slides in. My before measurements were similar. A bit higher in front and a bit lower in back. 29 3/4 Front. 28 3/4 Rear.