That bolt has to be torqued to atleast 72ft lbs then another 90 degrees or else that bolt will back up and your engine will be done.
@oscarpalacios71985 жыл бұрын
GREAT VIDEOS THANK YOU SO MUCH
@jorgemtz43195 жыл бұрын
Oscar Palacios y el torque esa polea no trae cuña,
@jorgemtz43195 жыл бұрын
Oscar Palacios pero me parece muy bien el video
@josevillasana70122 жыл бұрын
Good video help me a lot
@alm77073 жыл бұрын
If you do not lock the cams at tdc the crank sprocket ( that is not keyed to the crank) will likely turn as it is held in place by being squashed between the balancer and the front of the crank. A cam lobe with the valve compressed can make the cam turn and spin the sprocket on the crank a few degrees and now your timing will be way off, bent valves etc when you start it....... get the right tools and a new bolt as it is a stretch bolt you can only use once. torque it properly too.
@Luis_GonzaIez Жыл бұрын
No wonder mine runs extremely sloppy and turns off lol
@valentingheorghe16934 жыл бұрын
Using that impact wrench on the pulley bolt is the main problem when you want to unscrew it again. You can't precise set and control the torque on that impact gun. If the manufacturer says that this bolt requires two stage screwing, first to 100 Nm then turn another 90 degrees, the unscrewing shouldn't require excessive force, unless someone "wise" used an impact gun on the bolt and tighten it to much. When you need to unscrew the bolt it would be much better to lock the pulley with a special holding tool and use a hammer and a manual impact wrench on the bolt.
@xxuncexx3 жыл бұрын
Rubber on I think it’s the drive shaft is cracked
@tobylillie65405 жыл бұрын
so i took my pully off without setting to TDC or putting that tool in to lock the crank? what are my options now am i able to just rotate the engine to TDC and put this on?
@mohammadamro41324 жыл бұрын
You need special service tools to do that lol
@alm77073 жыл бұрын
If you do not lock the cams at tdc the crank sprocket ( that is not keyed to the crank) will likely turn as it is held in place by being squashed between the balancer and the front of the crank. A cam lobe with the valve compressed can make the cam turn and spin the sprocket on the crank a few degrees and now your timing will be way off, bent valves etc when you start it....... get the right tools and a new bolt as it is a stretch bolt you can only use once. torque it properly too.
@yoyyoy47894 жыл бұрын
what"s the simptom cranck pulley problem?
@gertis74205 жыл бұрын
Great video. I was thinking that you have to hold the camshafts with the special tool, But seems that is not necessary.
@ag3nto5784 жыл бұрын
You might get lucky this way but I would hold the balancer with a spanner wrench. Notice the crank moving when he takes out the bolt? He also did not torque the bolt correctly. The torque needed would shear off the temporary little bolt in the balancer. Where is the friction washer? I would not trust this repair for long.
@SimonM53 жыл бұрын
Does anyone know the size of this small holding bolt please?
@chriscusick68902 жыл бұрын
@@SimonM5 the harmonic balancer locating bolt is 6mm. The crank locking bolt is m10x1.5x33.55mm. I used a m10x1.5x40mm myself.
@chriscusick68902 жыл бұрын
@@SimonM5 mistake side bolt is 38.55mm.
@chriscusick68902 жыл бұрын
That little 6mm bolt is same as the timing cover bolts. That's what I used.
@micknightmare310 ай бұрын
that cv axel is fucked up lol
@miguelayalajimenez87213 жыл бұрын
El pully lleva 74 # de torque y 90°para que funcionen las alanderas diamantizadas no de mas ni de menos
@ccyy87473 жыл бұрын
傳動軸襯套破了?
@kaylapitchford33215 жыл бұрын
What size is the bolt on the crankshaft pulley 21mm or 22mm
@chm11755 жыл бұрын
21 mm size
@sabastianmukono5723 жыл бұрын
Good
@jamestvincent93605 жыл бұрын
Keep searching. There are better videos than this. Tech did not verify he was at TDC before and after pulley bolt was torqued. Also a new bolt and friction washer should be used.
@jerryc32015 жыл бұрын
Oh jesus....where's your video?
@rh2racing4 жыл бұрын
And it wasn't torqued down. I'm in the process of doing this and looking for more info and tips but I know enough to know this isn't right!
@jeffbirt88744 жыл бұрын
Jerry, are you implying that only people who video their work and post it know what they are talking about? Guess I need to confront my Mazda tech friend about this. Scammer's been working on my car with no videos, dammit!
@jamestvincent93604 жыл бұрын
Baxrok2 has some excellent videos for setting timing. Search his name. And then watch them a few times as once you get the concept it’s relatively easy process.
@kknowles66074 жыл бұрын
@@jeffbirt8874 ask your tech friend where I can get a replacement damper pulley from for my 04 Mazda Atenza
@kalindambozi23564 жыл бұрын
This proceedure is not correct. Always lock the camshafts
@chuyh014 жыл бұрын
to set timing yes. but to torque the bolt you do not want to lock the cams as the tool will definitely break the camshaft ends
@nyeahgarner2420 Жыл бұрын
Only if you remove the timing chain or loosen the sprockets. For this job, the pulley simply has to be aligned with the crankshaft sensor at TDC.
@lorenzohart95604 жыл бұрын
I want to hear how it ran after this.
@jeremiahbates11383 жыл бұрын
Lmfao so do I
@nct94663 жыл бұрын
A foreigner?!
@HoUsEoFcAtS784 жыл бұрын
Timing peg was not all the way in. Never reset crank to TDC. This is a hatchet job more than likely ran like shit after this job was done. If you're gonna do an "instructional" video, show everybody the proper way. This will end up blowing someone's motor.